Jump to content

Reverse light mod ideas (no bulb replacement)

Baker17

By Baker17
in Modifications, Wheels & Tires

 Share

Recommended Posts

Baker17 Enthusiast

Baker17

Posted
Posted

I'm looking to add more light to the back of the truck (2023 Silverado 1500 LT) for more visibility when backing up in the dark. LED bulb replacement is not an option for me, since I have aftermarket tailights. 

 

I looked into VLED LP-X but customer support told me it wont work because Silverado's trailering system will interfere with it. I asked if I could wire tap into the cargo light wires, so that the lights turn on when I toggle on cargo lights, but he wasn't sure if that would work or not.

 

Anyone have tried VLEDS or any other types of lights for reverse light? Any recommendations welcome!

  • Replies 30
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

nlindste
nlindste

I used this wiring harness from amazon to tie into my factory lighting system. I have 2 rigid flush mounted lights in the pockets on the rear bumper.  It has zero effect on the trailering system.

GETGONE
GETGONE

The Curt harness won't work on a GM because the 7 way plug is dead except for 12V+ and ground unless it detects a trailer plugged in. You need the harness that plugs in between the tail light wiring t

PureZ71
PureZ71

I used podholes bracket and mounted some Baja Design S1 lights. They also came with a harness that turns them on when your cargo lights are turned on.   https://podholes.com/products/pod-hol

Posted Images

GETGONE Enthusiast

GETGONE

Posted
Posted

You will need to wire the lights into a relay. The factory circuit will overload and shut off the lights when you add any additional lights. You can use the reverse light wire in the tail light as the trigger wire for the circuit. You can use the 12V+ from the trailer wiring circuit as the power source for the relay circuit.

nlindste Enthusiast

nlindste

Posted
Posted

I used this wiring harness from amazon to tie into my factory lighting system. I have 2 rigid flush mounted lights in the pockets on the rear bumper.  It has zero effect on the trailering system.

All I did is tied into the connector.

 

https://www.amazon.com/OPT7-Redline-Connect-Harness-Silverado/dp/B09YCD82H3

 

https://www.amazon.com/Rigid-Industries-Diffused-Resistant-Accessories/dp/B01HJ4G9QI

 

 

20231204_142102.jpg

  • Like 1
  • 1 month later...
Rich Rein Enthusiast

Rich Rein

Posted
Posted (edited)
On 12/19/2023 at 10:10 PM, nlindste said:

I used this wiring harness from amazon to tie into my factory lighting system. I have 2 rigid flush mounted lights in the pockets on the rear bumper.  It has zero effect on the trailering system.

All I did is tied into the connector.

 

https://www.amazon.com/OPT7-Redline-Connect-Harness-Silverado/dp/B09YCD82H3

 

https://www.amazon.com/Rigid-Industries-Diffused-Resistant-Accessories/dp/B01HJ4G9QI

 

 

20231204_142102.jpg

@nlindste I am looking at doing something similar,and trying to visualize this all while parts are en route - does the putco harness go between the trailering plug and the body harness as well as have to tap/connect into the taillight harness? Or just behind the bumper, and then some connecting to whatever auxiliary reverse lights you are adding?

Edited by Rich Rein
  • 2 weeks later...
GETGONE Enthusiast

GETGONE

Posted
Posted

The Curt harness won't work on a GM because the 7 way plug is dead except for 12V+ and ground unless it detects a trailer plugged in. You need the harness that plugs in between the tail light wiring to get all the brake and turn signals working.

  • Like 1
Niklasbraun Enthusiast

Niklasbraun

Posted
Posted
On 12/19/2023 at 5:29 AM, Baker17 said:

I'm looking to add more light to the back of the truck (2023 Silverado 1500 LT) for more visibility when backing up in the dark. LED bulb replacement is not an option for me, since I have aftermarket tailights. 

 

I looked into VLED LP-X but customer support told me it wont work because Silverado's trailering system will interfere with it. I asked if I could wire tap into the cargo light wires, so that the lights turn on when I toggle on cargo lights, but he wasn't sure if that would work or not.

 

Anyone have tried VLEDS or any other types of lights for reverse light? Any recommendations welcome!

Have you considered auxiliary lights? I've had success with Rigid Industries D-Series lights. You can mount them strategically, and they're pretty bright.

Also, don't overlook the possibility of integrating fiber optic lighting You could discreetly embed them into the truck bed or along the bumper. Sync them up with your reverse lights without messing with the trailering setup.

Another idea is using motion-activated LED strips. Strategically position them in the bed, and they'll illuminate when you start reversing.

Rich Rein Enthusiast

Rich Rein

Posted
Posted (edited)
On 1/29/2024 at 11:25 PM, GETGONE said:

The Putco harness is a T that plugs in between the left and right tail light harnesses and then has a flat 4 plus a white wire for reverse lights.

https://www.putco.com/product/blade-quick-connect-harness/529005/

 

Just to follow up (in case this helps anyone else) - I used the Putco harness. The reverse power comes from the driver's side, as does 3 of the four wires for the extra 4 pin connector (the green power wire is the only one to come from the passenger's side). As I was only using the harness to power auxiliary reverse lights (which I wanted automatically tied in to my truck's reverse function, no extra switch needed), I cut off the 4 pin connector on the Putco harness (which means that I no longer needed the passenger side connection at all), and used the reverse wire and ground wire coming off of the driver's side piece of the harness (capping off the other two wires and hiding the ends in the loom). Power from my auxiliary lights connected to the white wire from the harness, ground from each light to the black wire...and I am in business. No issues, works exactly as I had hoped - and looks factory in the way that it all connects in (and easily removable without lasting effect because of the Putco harness).IMG_20240209_201518.thumb.jpg.fea708da14088ccf2246c16d6b78ad67.jpg

Edited by Rich Rein
Transient Senior Enthusiast

Transient

Posted
Posted

https://accessories.chevrolet.com/product/60-inch-blade-led-tailgate-light-bar-by-putco®-associated-accessories-19418352?bac=112629&body=Crew Cab Pickup&bodyId=22&bodyNumDoors=5&bodyNumDoorsId=5&categoryId=197502&make=Chevrolet&makeId=47&model=Silverado 1500&modelId=491&year=2023

 

and this

 

https://www.bajadesigns.com/products/s1-hitch-light-kit-universal/?sku=448153

GETGONE Enthusiast

GETGONE

Posted
Posted

That's a LOT of money for something you can't even use when you have your hitch in and NEED lights to hook or unhook a trailer in the dark!

SierraStorm21 Enthusiast

SierraStorm21

Posted
Posted
2 hours ago, GETGONE said:

That's a LOT of money for something you can't even use when you have your hitch in and NEED lights to hook or unhook a trailer in the dark!

It is...it went onsale during xmas time for $50 off which is still expensive imo. However for me, it'd work as I almost never tow anything, much less have to hook up in the dark. 

 

There's also the boostauto mod that's super cheap. How well it works I don't know. Was considering that too or maybe both

https://boostautoparts.com/products/bed-cargo-and-reverse-wiring-harness-2019?year=2021&make=GMC&model=Sierra 1500

GETGONE Enthusiast

GETGONE

Posted
Posted
12 hours ago, Mstorm18 said:

It is...it went onsale during xmas time for $50 off which is still expensive imo. However for me, it'd work as I almost never tow anything, much less have to hook up in the dark. 

 

There's also the boostauto mod that's super cheap. How well it works I don't know. Was considering that too or maybe both

https://boostautoparts.com/products/bed-cargo-and-reverse-wiring-harness-2019?year=2021&make=GMC&model=Sierra 1500

Why have a truck if you don't tow?

 

I made my own "boost auto" mod for a few cents. I have it set so the reverse lights come on when I press the cargo light button so it makes it super bright along with the LED cubes I added to the bottom of the hitch. Works great for hooking up a trailer or loading stuff in the bed in the dark.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Mellowth
      Tonneau cover and rack combo

      By Mellowth · Posted

      I found a setup that lets me open the cover partway with racks installed, using side-rail-mounted systems for easy access.
    • Chuck FB
      first oil change - 2026 2500HD gas

      By Chuck FB · Posted

      Typically its said and I agree so far that the engine oil drain plug oring is not required to be changed out unless you see some damage happening to the oring as apparently the oring lasts well. The dealer I have been getting a few parts from never even stocked the oring but instead stocked the whole drain plug that comes with a new oring which for the dealer is easier because they just throw in a new drain plug if there was any question about damage on it as well and charge the customer accordingly but again only if it is needed.    Also a hint about the drain plug oring to help it last vs a risk of causing damage to it, after its been removed and wiped off or washed off ( that is a whole other topic about some solvents damaging orings because some solvent types do ) to make sure to relube the oring with a bit of new oil so that it won't "grip" on the sealing surface of the pan and needlessly stress out the oring. Its no different than putting some oil on the sealing ring of the engine oil filter. So I just grabbed a new drain plug to have on hand although more recently bought just the oring as well but as its special it costs half the price of the drain plug ... !   Since you mentioned the hate to be empty handed theme, I am not sure what you have in the way of filter removal tools as I like using the exact sized for the filter steel 1" wide band with side to side swivel handle filter removal tool, and it can be used to snug up the filter without risk of damaging a filter as well ( its probably a lisle brand I have ). The drain plug hex size is 15mm and I always like using a 6 point socket if I have a choice and with this truck I've been using just a 3/8 ratchet that has a fairly long handle. Do you have a funnel that will work to pour oil in as that is definitely the short coming bastard part about the design with that fill port on the valve cover on such an angle that no normal funnel will even work. There are adapters and things on the market that will set into or screw into that fill port, I didn't want to deal with US shipping as that is all I was seeing at the time so caved and bought a Lisle brand multi vehicle fit adapter funnel kit and it really works well but there are much less expensive adapters out there that work in conjunction with an off the shelf funnel that would do the job also. Now that I have it, I like how it works and works so slick with the shape of the Amsoil 1 quart containers I have now switched over to. Whatever you do, have a funnel system of some sort as you will be swearing if you dropped the oil and then realize you have nothing to properly pour new oil in without spilling it all over the engine !.     Other comments, quite a bit of oil flows out down the filter when its cracked loose due to the housing above the filter so let it dribble down the filter until it slacks off flow and then remove the filter to create less possible mess. It seems these engines can sit for quite a while and drip and if you have time let it sit there and drip out of the engine as much as it wants. Also a good time to grease the 9 zerks on the front end, that's my typical practice anyway to grease the suspension and steering each time I change the oil. And remember to reset the oil change minder ( not something I am used to doing with older vehicles and equipment ). 
    • Aimatdeer
      Correct way to service 2024 l8t allison trans?

      By Aimatdeer · Posted

      I really did not measure what came out. I carefully followed directions to check level after i did the spill and fill and filter change. I used 10 quarts. 9 was not quite enough. My trans temp was about 175 when I checked it. Truck sitting in my driveway very close to level where I always check oil pretty much every time for consistency. My driveway is just ever so slightly downhill to run water to the street.
    • Warehouser
      Audio Dampening and quiet

      By Warehouser · Posted

      Sounds like maybe it's announcing Navigation turns or Alerts (it mutes the music) ? When it mutes again, turn up the volume quickly and see if maybe the navigation volume is really low?
    • KARNUT
      Navigating senior years.

      By KARNUT · Posted

      If you were a classic car you would be a retro ride😆 Thank goodness for modern medicine. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...