Jump to content

2014+ Lowering / Drop Kits

mjw930

By mjw930
in Modifications & Accessories

 Share

Recommended Posts

Dirtbiker Enthusiast

Dirtbiker

Posted
Posted

I did have a friend that had a lift kit on his 2500 have his ubolts come loose. I don't know any of the specifics though like if he retorqued then or not. I just know they came loose one day.

  • Replies 3.4k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Heavy_Static
Heavy_Static

A few pics from last week:    

bakerrr
bakerrr

First post here Picked her about 2 weeks ago couldn't wait to start modifying it. Just installed Belltechs 4/7 drop this weekend It's low enough for the time being ??  

Nasty
Nasty

Posted Images

brentadams646 Enthusiast

brentadams646

Posted
Posted

I realize shackles will lower the rear, just curious if any one has removed the rear 2" blocks. In my simple mind that would be the easiest way to level the rear with the front. As far as the U-bolt, once the blocks are removed, your on new threads so in my mind you would not need new ones.

 

Anyone ??

 

Mike

 

I've heard in some instances you actually running out of threads on the u-bolts therefor needing new ones.

brentadams646 Enthusiast

brentadams646

Posted
Posted (edited)

Why not just install leveling shackles? 2 bolts on each side and your done. Most standard shackles have holes for 1" or 2" of lowering.

Edited by brentadams646
mzodarg Senior Enthusiast

mzodarg

Posted
Posted

Why not just install leveling shackles? 2 bolts on each side and your done. Most standard shackles have holes for 1" or 2" of lowering.

WHy not remove the 2" blocks if it can be done? I am fully aware of the shackles, cheap and will have the desired affect. I like free.99 better. :D

mzodarg Senior Enthusiast

mzodarg

Posted
Posted (edited)

The blocks are like 1.25"

YOU ARE CORRECT 1.257 by my micrometer. I also measured the fender height from the top of each tire. Front is 6" rear is 8" (both measurements are approximate, with .25"). Looks like some shackles are my next purchase.

 

Mike

Edited by mzodarg
Chris Senior Enthusiast

Chris

Posted
Posted

They are the same blocks from 07-13. There is a set in my toolbox

mzodarg Senior Enthusiast

mzodarg

Posted
Posted

They are the same blocks from 07-13. There is a set in my toolbox

IC thanks, Any idea if the Rancho shocks will work with shackles? I'll change them eventually but I'm not sure with what.

mzodarg Senior Enthusiast

mzodarg

Posted
Posted

Might have to get some shock brackets

I'll do some research. If anyone has any details with lowering shackles and the Rancho shocks, please share.

 

Thanks,

Mike

TJay74 Senior Enthusiast

TJay74

Posted
Posted

The Rancho shocks will work, though the dampening will be a little soft since the shock will be riding more in the compressed part of the valving. Rancho is waiting on their OEM side to get them the specs so they can see if there is another shock that will work with a lowered truck.

mzodarg Senior Enthusiast

mzodarg

Posted
Posted

The Rancho shocks will work, though the dampening will be a little soft since the shock will be riding more in the compressed part of the valving. Rancho is waiting on their OEM side to get them the specs so they can see if there is another shock that will work with a lowered truck.

Cool, thanks!

 

Mike

Black14crew Enthusiast

Black14crew

Posted
Posted

Hi guys. I don't know why but I was thinking the rough country spindle/ flip kit was for both 2wd and 4wd trucks. I just went to there site to order but it looks like it's only a 2wd kit. I'm sure the flip kit is the same, but are the spindles the same as the 4wd?

Or dose anyone know of a 4wd drop spindle?

 

I know, I know why lower a 4wd???? Well I live in Iowa and there a lot of snow here! I don't want to be siting on the ground just a 2/4 drop to take up some of the extra wheel well chevy seam to put in the design. I will also be adding a air ride overload setup so I can still pull a trailer when and if need to.

  • Like 1
loganbent Enthusiast

loganbent

Posted
Posted

I'm probably going to start with just dropping the rear, not sure if I'll pull the 1.25" riser blocks out or actually do a 2" drop shackle, couple other threads in the last few days have had similar discussions

 

And would be interested in what airbag setup you're thinking of running if you've picked one out

BamCam Enthusiast

BamCam

Posted
Posted

You should contact these guys.

http://www.mcgaughys-suspension.com/

 

When I was in the market for a '14 4x4 I contacted them and they told me their '13 3/5 kit should work on a new truck as the suspension is very similar. They did not get a chance to test on a new truck yet but told me if I purchased the kit and had any problems with the kit or install they would give me a full refund. I believe the guy's name was Sean. This was 2-3 months ago so they may have had a chance to install one on a 4x4 since then. Hope this helps.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,964
    Total Members
    8,960
    Most Online
    BrandonFranceschi
    Newest Member
    BrandonFranceschi
    Joined

  • Who's Online   4 Members, 0 Anonymous, 1,231 Guests (See full list)

  • Latest Articles

  • Posts

    • Jsdirt
      2010 Avalanche 5.3 not running correctly after engine swap.

      By Jsdirt · Posted

      If everything checks out at the MAF, then the MAF is BAD, new or not.   You don't need a signal generator to troubleshoot this. PCM needs ALL powers and ALL grounds able to light a halogen headlight bulb - if it can light the bulb bright, then the wiring is good enough to run the PCM.   Best thing you can do for yourself is spend some time here: scannerdanner.com - Check out all his YouTube videos on similar issues. If you decide to subscribe it's the best bang-for-buck ratio in the automotive world, hands-down. He's got TONS of free vids on YouTube, too.
    • Tyler Gibbs
      PF63 Oil Filters Going Away?

      By Tyler Gibbs · Posted

      You got that Hengst D110??
    • contrabombarde
      2010 Avalanche 5.3 not running correctly after engine swap.

      By contrabombarde · Posted

      Yes, I used my multimeter to probe all of the wires at the MAF, both with the sensor connected, sensor disconnected, key on engine off, key on engine running, etc etc etc. I probed all of the wires again at the PCM, at the connectors, etc. All voltages are what they should be according to the service manual/wiring diagrams. All grounds are good, less than 20 millivolts from the battery negative under load. Both at the connector of the MAF, at the PCM connector etc.      I know this throws a pretty big wrench into things, but this truck was acting up before the swap. I don't have very much information, if any on what was causing it, but if you cleared all of the dtcs it would do the same thing where it would crank, fire, then die. And it would do the same thing a dozen or so times, and eventually it would start and run, but the difference is that it would run and actually be drivable. Whereas now if you can drive it at all, it goes into reduced power mode almost immediately, and even then it's not running correctly. When you come to a stop at a light it stumbles down to for 500 RPM before catching itself and returning to the smooth idle. And if you go more than about 50% throttle then it immediately goes back to doing the misfire thing.    Like I said, I know that throws a wrench into things, and unfortunately I was not able to pull any data or anything like that before I did this work, so I don't have much to go on.    I'm trying to not fixate on one particular thing as the cause of the problem, but it seems like all avenues are pointing me towards the PCM. Like I said I have tested the wiring extensively (see above), and during cranking the sensor does produce seemingly legitimate values at least according to my multimeter, but as soon as the engine fires those values quickly descend into gibberish. I've tried it with multiple different known working sensors, I have done literally every test I can think of multiple times on the wiring (probing the signals, probing the pins with the sensors unplugged, probing the pins at the PCM, voltage drop, voltage drop under load, continuity, ohms, and double-checking everything against the wiring diagrams/ proper values in the service data.)    Another thing that pushes me towards a possible PCM failure is, I have noticed in troubleshooting a little bit taking a break and coming back, that when I leave the truck to sit for a while and cool off, it starts and runs smoothly when I first start it up. However once it warms up. It starts having problems. For example, when I went out to the truck this morning after it had been sitting overnight, I was actually able to drive it down the block. And then once I got on the throttle a Little bit after going about a thousand ft, it started misfiring again. I pulled it back into the driveway, shut it down, and started it back up. It idled smoothly. As soon as I touched the throttle it did the misfire thing again. From then on as soon as I started it it would misfire. I shut the truck off and went to go get a coffee and do a bit more research. When I came back out I started the truck up and it immediately went into the smooth idle. After a couple of minutes of playing around with it, it would not idle smoothly anymore. Let it sit a couple of hours, rinse and repeat. This makes me think with temperature change something is going wrong inside the PCM. I have the PCM out of the 2007 donor vehicle and I'm thinking of getting a one-day subscription to the ACDelco programming service to try and program that and see if it helps.   Like I said, I'm really trying to not fixate myself on one potential cause, but it seems everything is pointing me towards PCM failure. I would really like to try to confirm that, but unfortunately I don't have an oscilloscope or a signal generator to do the GM service procedure where you feed 5 khz into the signal pin. 
    • Jsdirt
      2010 Avalanche 5.3 not running correctly after engine swap.

      By Jsdirt · Posted

      Ahh, sorry about that - I got some bad info. Newdude is correct. That's what I get for working 13 hours straight ... on my "vacation", lol.   Should've checked the files I had instead of the internet.   Anyway ... this is GREAT news, since this would've been an absolute friggin nightmare to get working.   I don't think the lack of VVT is causing this - you've got another issue. Wiring, I'm betting.   I'm telling you right now, your computer isn't bad. If it worked before the swap, it's working now. You need to do some more (better) diagnostics and figure out exactly what you're missing. Did you test every wire directly at the MAF? Have 5V reference? Ground? If you're reading ZERO g/s, your Hz isn't much use - it's going to be the wrong value anyway. The MAF is not working, and you need to find out WHY.   I got this off the net, so VERIFY first: Pin A: Black (BLK) wire, Circuit 552, serves as the Sensor Return (Ground).  Pin B: Tan (TAN) wire, Circuit 472, carries the Intake Air Temperature (IAT) signal.  Pin C: Yellow (YEL) wire, Circuit 492, is the primary MAF Sensor Signal output to the PCM. Pin D: Pink (PNK) wire, Circuit 339 or 539, provides Ignition 1 Voltage (Power).  Pin E: Tan/Black wire, Circuit 552 or similar, often associated with the Intake Air Temperature ground or signal return.  Global-A list: https://postimg.cc/KKJnQC85    
    • parthery
      GM Hard Folding Tonneau by REV review

      By parthery · Posted

      Correct....the end user can't reach to Realtruck directly like they can if they purchase a Bak, Undercover, etc...  It has to go through a dealer.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...