Jump to content

Center console swap?

quickvert1

By quickvert1
in Modifications & Accessories

 Share

Recommended Posts

Jaychevy81 Enthusiast

Jaychevy81

Posted
Posted

Thanks for the reply i ordered console # 23466980 the side trims and the synthesis plate. Cant wait to get the parts and start planning the swap....

  • Replies 1.9k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

darkfox1
darkfox1

OK.. mine's in.   Here's a writeup, cos I haven't seen one so far.   1. remove the "ash tray" and cig. ligther in your dash with 3 t-10 torx screws, and 2 clips. 2. Remove the radio trim, clips i

dla
dla

I always wanted a RCSB with buckets and a center console...   Received and installed mine yesterday. Very straight forward, thanks for all who posted instructions and part numbers.   Possibly to h

o7bodybagged
o7bodybagged

Finally the console is complete now ready for the install and see what other problems I run into

Posted Images

jchildress Enthusiast

jchildress

Posted
Posted

So I had to do the opposite of most folks. I had to take a great looking console out for a jump seat. My jump seat did not come with a wiring harness, but I may buy one soon for it.

 

My issue is that I have not figured out where this jump seat wiring harness will plug in at. I don't see any available "ports" around the other two seats or where I took the console out. Is that because there is a totally separate "Main" wiring harness that I'm missing? Anybody have any pictures of where it plugs in at? I'm trying to keep from splicing all kinds of stuff.

 

Thanks much!

1911-A1 Enthusiast

1911-A1

Posted
Posted

I don't think you're going to find one.I think you will have to splice a harness to connect to the plug in the dash.Basically the same as I will have to splice the console harness to the seat harness to add the console to my truck.It's the same only different. :)

jchildress Enthusiast

jchildress

Posted
Posted

Yeah, It was a problem. The subwoofer fit perfectly under the console. I did take it out for now. Not sure what to do with it yet, but it doesn't fit anywhere else.​

Jaychevy81 Enthusiast

Jaychevy81

Posted
Posted

Jchildress you would be better off buying the harness for the full console and re route it mostly everything will plug and play. No splicing or cutting just a thought.

Jaychevy81 Enthusiast

Jaychevy81

Posted
Posted

Or if your interested I have the big plug from my console that would plug into your harness you would have to splice it that way but I don't need it. Jay

  • Like 1
jchildress Enthusiast

jchildress

Posted
Posted

Hi... I went back out and checked and the "Ebay Item Number" is 201516242250... I suppose you can search with that.

 

As for the Subwoofer... I have it, but would like to just send it to whoever buys the console which makes shipping a little easier. Hope you guys have a good day.

Swankster988 Enthusiast

Swankster988

Posted
Posted

Does anyone on here have the part numbers for the cocoa/dune interior?


No, it's Jet Black

 

Okay, it kind of looked cocoa/dune in the photos. Thanks.

Liquidfx17 Enthusiast

Liquidfx17

Posted
Posted

Anyone done a 2016 console swap? Or just the center arm rest swap for the wireless charging pad?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.6k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,993
    Total Members
    8,960
    Most Online
    President Roberto
    Newest Member
    President Roberto
    Joined

  • Who's Online   1 Member, 0 Anonymous, 291 Guests (See full list)

  • Latest Articles

  • Posts

    • bwiese
      upgrading speakers on 2026 std cab WT...

      By bwiese · Posted

      I don't wanna do major surgery/upgrades, behind-the-dash work, add amps, change radio etc. on my '26 std cab WT. On the WT, it has the base 7" IOR infotainment setup, and only two speakers (doors). Since I listen to classical, looked around for speakers that do well and dug thru reviews. Two-way speakers were found to be better than 3-way. So I've ordered a pair of  Infinity Reference REF-9632IX 2 way speakers.  [These may  or may not have been discontinued / succeeded by the 3-way ...9633 ones.]    These speakers are lauded for 3 ohm and 94db sensitivity spec so they'll work well for ordinary base car radios without amps and offer better performance (quality,  strength) than  default base paper-cone speakers. They'll be installed in a few days and I'll let y'all know what I think. Bill W San Jose      
    • RyanbabZ71
      RyanbabZ71's 2019 High Country

      By RyanbabZ71 · Posted

      Thanks!   Changed out the rear shocks today to Bilstein 5100s.  So far feel much better. The stock Rancho were wore out.  Lots of heavy hauling (2 moves, home renovations, etc).  Next up is new BFG tires Monday.  Cant wait the current tires have little to no wet traction and are super loud (hum)    
    • Snowcamo
      No high speed fans...

      By Snowcamo · Posted

      Ok, I got the all the codes. What do you all think would be a place to start?
    • Chuck FB
      Correct way to service 2024 l8t allison trans?

      By Chuck FB · Posted

      How about I just point to the factory pans stand pipe little drain plug and claim its a pan with a real drain plug !. I just couldn't swallow the fact that a Dorman pan which at this point is probably the only pan out there that fits the gas version truck cost that much up here in Canada so I decided initially anyway to skip it and see what I thought of pulling the pan method and down the road if I felt inclined enough then I would either install a drain plug kit in the factory pan if there is enough room for it, or have a bung welded onto it, or put an aftermarket pan on. The thing is if the pan is not pulled then the magnets in the pan can't be inspected and cleaned or if wanting to change out the filter. However of course it certainly would make the job easier to be able to drop the oil first before having to handle the pan if dropping the pan that go around was the goal.    I knew a guy locally that was doing custom field spraying years ago with a pickup pulling a ground driven sprayer, I believe it was a GM pickup with an automatic trans. He had a drain plug in his pan and would drop the oil out of it once a week and top it back up through the dipstick tube to keep refreshing a portion of the oil often and that made the transmission last far longer than had he done nothing. Soft fields pulling 500 gallons of water at the start of each mixed up sprayer tank batch and in low range sucking along. I imagine he got some tips from other custom sprayer outfits doing the same thing at the time and learning from their blown up tranny mistakes. Transmissions then had no lock up converter so would cook the crap out of the fluid slipping that much and it would not have been synthetic fluid either. 
    • KARNUT
      Gas Prices

      By KARNUT · Posted

      3.39 Kroger’s in Montgomery Texas. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...