Jump to content

Center console swap?

quickvert1

By quickvert1
in Modifications & Accessories

 Share

Recommended Posts

AdamZ71 Enthusiast

AdamZ71

Posted
Posted

Were you able to get the 3 USBs up front fully functional using the standard USB to mini cable in combo with the existing cable to the HMI? I was thinking of doing the same thing since the USB is pretty useless to me in the glove box. This is the last piece I want to figure out before installing the console. I've already combined both harnesses to make one hybrid...

The 3 USBs up front will all charge with the standard to mini and existing USB to HMI cord but do not communicate with the radio like the ones inside the console. Like you said though the one in the glovebox is quite useless to me too. Rather have the 3 upfront charging than the one in he glovebox

  • Replies 1.9k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

darkfox1
darkfox1

OK.. mine's in.   Here's a writeup, cos I haven't seen one so far.   1. remove the "ash tray" and cig. ligther in your dash with 3 t-10 torx screws, and 2 clips. 2. Remove the radio trim, clips i

dla
dla

I always wanted a RCSB with buckets and a center console...   Received and installed mine yesterday. Very straight forward, thanks for all who posted instructions and part numbers.   Possibly to h

o7bodybagged
o7bodybagged

Finally the console is complete now ready for the install and see what other problems I run into

Posted Images

Criscone Enthusiast

Criscone

Posted
Posted

is it true the black console is no longer available? every place I've checked says its discontinued.

AdamZ71 Enthusiast

AdamZ71

Posted
Posted

Seen lots of 2017s with full consoles on the lot- the part number you are using probably references the console without the wireless charger , all the new ones have the wireless charger , no option without . They may not be making them anymore without, but don't quote me on that

Criscone Enthusiast

Criscone

Posted
Posted

Called a couple dealers, they said the same thing. Black center console isn't available for purchase. Only "cocoa" color. Well this sucks..

Black-Z71 Enthusiast

Black-Z71

Posted
Posted

Called a couple dealers, they said the same thing. Black center console isn't available for purchase. Only "cocoa" color. Well this sucks..

Are you using part number 23466980? I got mine new on eBay. I see two for sale on there now...

Criscone Enthusiast

Criscone

Posted
Posted

I was just using my truck as well as a part number from earlier in this post. Now what number is that console from? Still have to buy the lid and everything seperate correct?

Criscone Enthusiast

Criscone

Posted
Posted

Are you using part number 23466980? I got mine new on eBay. I see two for sale on there now...

Did yours come with the padded leather top? I don't see it in the picture. 400 shipped on eBay but 550 shipped from gmpartsdirect. Wow!

Black-Z71 Enthusiast

Black-Z71

Posted
Posted

Did yours come with the padded leather top? I don't see it in the picture. 400 shipped on eBay but 550 shipped from gmpartsdirect. Wow!

The picture is deceiving...mine came complete with the black padded top (don't think it's leather) and the back panel. The other pieces you need are the front bracket, the side trim (left and right) and the top plate which comes with the cup holder...

tbarn Senior Enthusiast

tbarn

Posted
Posted

I have a top plate for sale for 16-17. USB 2-12v and 110v

Sil2500 Enthusiast

Sil2500

Posted
Posted

I just finished the swap and would like to thank those ahead of me for all the information.

 

I used these part numbers

 

23467113 Upper trim panel in Synthesis

22776807 Console assembly front bracket

23467516 Side trim

22817347 Side trim

23466980 Console

19303284 Cable from HMI to USB

 

I have a 2016 2500HD LT model with black leather seat. The cable I used is a perfect match to the HMI and USB(3) ports. I used the existing harness for the rear ports, and then salvaged the LED wiring, a 12V plug, and USB power plug from the new harness. I spliced the three together and connected them to continuous power at the fuse panel on right side. I then removed the glove box USB cable and used the open port on the HMI for the new cable to the triple USB port.

 

I have everything working including data and charging at the USB's. I originally had Apple carplay in the original configuration, but that no longer works. I think it might be due to the new console and the ports that are installed. Carplay wasnt' available on the 2015 models, so it may be the configuration of the hub built into the ports. I found another console 23466999 which I believe is for the 2016 models but I couldn't confirm that. I also preferred having the SD card slot over the carplay feature.

 

 

 

 


Black-Z71 Enthusiast

Black-Z71

Posted
Posted

I have a 2016 2500HD LT model with black leather seat. The cable I used is a perfect match to the HMI and USB(3) ports. I used the existing harness for the rear ports, and then salvaged the LED wiring, a 12V plug, and USB power plug from the new harness. I spliced the three together and connected them to continuous power at the fuse panel on right side. I then removed the glove box USB cable and used the open port on the HMI for the new cable to the triple USB port.

 

How did you setup your wiring to get data and charging to the front USBs? Did you splice together the two USB power harnesses (red, black, blue, green, purple and gray wires)? I'm going to use the existing HMI cable from the goovebox and add a mini USB to standard USB cable to the front USBs which should work...

Sil2500 Enthusiast

Sil2500

Posted
Posted (edited)

How did you setup your wiring to get data and charging to the front USBs? Did you splice together the two USB power harnesses (red, black, blue, green, purple and gray wires)? I'm going to use the existing HMI cable from the goovebox and add a mini USB to standard USB cable to the front USBs which should work...

 

I did not splice those two together. I used the red and black wires only from the USB power plug off the new harness. I believe TBarn stated in an earlier post that the other wires (blue, green, purple, and gray) weren't used for anything. I spliced the (red and black) with the (Purple/yellow and black) from the 12V plug as well as the (brown/white and black) from the LED wiring. Then I connected those two single leads to power and ground. I didn't want to splice into the existing harness at all for warranty reasons.

 

So I have one lead that powers the LED, additional 12V plug and Triple USB port in front of console. For the Data portion I used the cable listed above AC Delco 19303284 to run from the Triple USB to the HMI. I didn't want an additional connection involved with the data transfer, and everything snapped together like OEM.

 

Hope this helps.

Edited by Sil2500
Black-Z71 Enthusiast

Black-Z71

Posted
Posted

I did not splice those two together. I used the red and black wires only from the USB power plug off the new harness. I believe TBarn stated in an earlier post that the other wires (blue, green, purple, and gray) weren't used for anything. I spliced the (red and black) with the (Purple/yellow and black) from the 12V plug as well as the (brown/white and black) from the LED wiring. Then I connected those two single leads to power and ground. I didn't want to splice into the existing harness at all for warranty reasons.

 

So I have one lead that powers the LED, additional 12V plug and Triple USB port in front of console. For the Data portion I used the cable listed above AC Delco 19303284 to run from the Triple USB to the HMI. I didn't want an additional connection involved with the data transfer, and everything snapped together like OEM.

 

Hope this helps.

Interesting...I would not think that the front USBs would work for data without connecting all the wires from the harness. Others have failed to get data with the same setup. I have my wiring done and will install the console this weekend and report back. Thanks.

AdamZ71 Enthusiast

AdamZ71

Posted
Posted

Interesting...I would not think that the front USBs would work for data without connecting all the wires from the harness. Others have failed to get data with the same setup. I have my wiring done and will install the console this weekend and report back. Thanks.

 

^^ also interested to know if that works out for you -and which coloured port on the HMI you used to get it to work.... defiantly worth the couple extra bucks to buy the Delco cable to have it function that way, and strange how a setup like mine does not....

Sil2500 Enthusiast

Sil2500

Posted
Posted

 

^^ also interested to know if that works out for you -and which coloured port on the HMI you used to get it to work.... defiantly worth the couple extra bucks to buy the Delco cable to have it function that way, and strange how a setup like mine does not....

 

It is working. To verify, I shut off bluetooth on my phone, ejected data card, so the only input I have is the lightning cable from my iphone plugged into the USB port.

 

The cable I specified above is color coded with a green end to match the green input (port originally used for glove box USB cable connection) on the HMI, and a grey end for the port on the rear of the triple USB. More importantly, the angled notch is on the correct side for each plug, so there is no trimming needed and they snap in solidly.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • diyer2
      AFM Experience

      By diyer2 · Posted

      Hey guys, sorry for the confusison about this. This wasn't my experainnce, it was copied and pasted fom the net. 
    • KARNUT
      AFM Experience

      By KARNUT · Posted

      The problem with failure rates or increase failures are there’s people who don’t have a problem. What are you doing wrong they say. We had 4 5.7 GM diesel’s in the family when they came out. One was flawless. My uncle who happened to be the most abusive. Early rotary engines were known to use oil. I abused my first car so bad in six months I replaced the clutch, transmission and rear end. It didn’t use oil. My brother in law has a 2013 Tahoe and an older Yukon. The Yukon has 280K miles. The Tahoe around 175K. He runs them to about 300K. If his lifters fail before that time he would consider it a failure. My Hondas, I know people hate it when I mention them. Identical engines. One with cylinder deactivation one doesn’t have it. One shudders when the eco light goes on or off. Cylinder deactivation. But wait! According to the web. It can happen with lock up too. So now people in the know are changing the oil and transmission fluid more often. Then you read it could be a programing issue. So what do you do? There’s lots of money involved. I see three ways to deal with it. One only works if you don’t drive lots of miles. Lease, never get out of warranty. Or only buy older vehicles with a good track record. They all have bad runs. Usually when there’s a change. Even Toyota and Honda. 
    • Grumpy Bear
      AFM Experience

      By Grumpy Bear · Posted

      Question @diyer2 on this line if you please. Are you saying the shudder is the system turning on and off at the frequency of the shudder? Guess I'm asking if you are saying you have seen it do this with the bi-direction scan tool in graph mode? If so have you been able to discern the 'trigger'. Something is telling to cycle rapidly.    My truck just started doing this recently. 197K on the clock. My response has been M5 anything under 55 mph. I treat it like a lugging stick shift. Gear down and let it spin a bit. Engauge M5, then tow mode and then M6 lets the trans stay in 5th but the AFM is active. Smooth like Skippy.    My thought was that as a machine ages the friction gets lower and as the system is load based, the lower friction would allow it to turn on at ever lower rpm until it reaches the lugging point. And yes I am ignorant of any minimum rpm requirement for the system. If you know that would be useful information.    As you know I run a Scan-Gauge II which allows me to watch the On/Off of the signal to the VLOM. While in the shudder mode I'm not seeing is cycle at that frequency or at all for that matter outside the triggers @newdude posted a few years back. Now is it possible that the refresh rate isn't fast enough to catch it? Maybe. It is why I asked my first question about graphing and trigging parameter.     As we have observed from members here the failure point is all over the map miles wise as you note yourself in your opening post. That by itself begs a few questions like fellows that comment on these lifters failing even after the system has been disabled. Long after. 😬   https://www.enginelabs.com/news/tech-tips-replacing-ls-active-fuel-management-lifters-with-melling/   The Gen5 lifters operate the same as the LS versions. In fact they are the same lifter.    https://www.enginelabs.com/tech-stories/sorting-out-gen-v-lt-lifter-failure-with-a-simple-valvetrain-fix/        
    • SwitchBladeSierra
      14-18 Sierra 1500 Heated Steering Wheel Help

      By SwitchBladeSierra · Posted

      UPDATE 2: Steering wheel control backlights and control of the cluster can supposedly be achieved by adding a wire to pin 20 of the cluster and tapping it to pin 2 of the main clock spring harness. I'm going to give it a shot - will update  
    • newdude
      Seems to be Missing a lot of Updates

      By newdude · Posted

      GM Global A pickups 2019-2022 can do OTA programming for the radio.  GM VIP (GM Global B) can do OTAs for almost every module on board.  So a 2022.5 and newer pickup can do OTAs for recalls like the 2.7 fuel flow recall.  EVs get OTAs that improve one pedal driving, radio issues, HVAC issues, updated battery management software, etc.     So age of the vehicle/what GM electrical platform its on will alter what amount of updates can be pushed on OTAs.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...