-
Similar Content
-
- 10 replies
- 22,491 views
-
- 1 reply
- 7,616 views
-
- 2 replies
- 3,768 views
-
- 1 reply
- 2,421 views
-
- 4 replies
- 10,250 views
-
-
Recently Browsing 0 members
- No registered users viewing this page.
-
Forum Statistics
250.4k
Total Topics2.7m
Total Posts -
Member Statistics
342,857
Total Members8,960
Most Online
-
Who's Online 2 Members, 0 Anonymous, 554 Guests (See full list)
-
Latest Articles
-
Posts
-
By Black02Silverado · Posted
Dawn also works well. I also use Simple Green. -
So you are saying that there is a water to oil transmission fluid "heater" along with an air to atf heat exchanger? Where do I get hold of a diagram/microfiche of that routing? Is the water to oil cooler a bar plate job between the trans thermostat and the air to oil cooler? In the 2022 10L80/90? valve body there is a valve called the Cooler Thermostat Valve that gets modded to eliminate regulation to the flow to the cooler. There are two styles - the 2022 has no brass thermostat, but later versions seem to have it. Testing today after the valve body kit install, zero change in gauge temp unloaded - 180F at 84*F unloaded, so the atf heater is doing its job. The positive so far is the lag in shifting from R to D has been eliminated. There is a brass "thermostat" in the Cooler Thermostat Valve that is removed with the NextGen kit for the 10L1000 - 135F gauge temp with a 5000lb boat in small rolling hills at 85*F. -
By asilverblazer · Posted
Wonder what happened to the "MEGA"max 8.3 rumors. I haven't had any rust issues, but the wax sure is ugly. Good to hear, considering the joint venture with International ended. -
I still use kerosene and a brush for clean up since it's easily available to me. Then pressure wash if possible. Seems like on the really thick goo, brake clean doesn't work so well, at least for me. have also used simple green or similar on light coatings of oil/dirt. Again brushing it and agitating -
I agree and why it seemed to make logical sense to swap it out before it did have a failure mode. I have no idea what the typical mileage was reached on the Allison 6 speed and variants from the beginning of the Duramax engine series but they were not putting through as much power either other than maybe the 2017 to 2019 models relative to the 2020 model trucks with the 10 speed. I am guessing there were some changes/upgrades over the years with that transmission as the engine in front of it certainly changed in output. I see some reviews of the Ram with the new 8 speed and comments about how great this transmission will be relative to the Ford and GM, but only time will really reveal how it all plays out as use and abuse always eventually show how good something is or what weakness it may have.
-
-
GM-Trucks.com Clubs
-
Black Truck Club
Open Club · 612 members
-
White Truck Club
Open Club · 380 members
-
Canadian Owners Club
Open Club · 282 members
-
Red Truck Club
Open Club · 157 members
-
diesel 3.0
Open Club · 281 members
-
Texas Owner's Group
Open Club · 371 members
-
NorthSky Blue Club
Open Club · 118 members
-
Midwest Owner's Group
Open Club · 213 members
-
2015 Custom Sport Club
Open Club · 5 members
-
GM Snow Plowing Club HD
Closed Club · 14 members
-
-
Popular Contributors
-
1
.thumb.JPG.2c573de60d3a3a4407c7d92298db46dd.JPG)
-
2
-
3
-
4
-
5
-
-
Recommended Posts
Archived
This topic is now archived and is closed to further replies.