Jump to content

Recommended Posts

Posted

Is getting the rear cover gasket from the dealer the best option?

 

To clean the G80, brake cleaner?

 

No silicone, right?

Posted

The gasket is reusable if you carefully remove the cover. Brake cleaner works well along with a lint free cloth. Refill with Amsoil Severe Gear oil.

Posted (edited)

Thank you. So spray the inside of the diff, wipe inside and good to go?

 

Chlorinated or non? Does it matter?

 

 

Swapping out front to Amsoil too.

Thanks again.

Edited by WilliamBos
Posted

Thanks again. Woukd you happen to know the service intervals for the rear diff?

 

 

Sent from my Z30 using Tapatalk

Posted

I bought a gasket from Amazon. I have the 14 bolt rear end

 

 

Ryan

Posted

I did my rear end, no G80 though. I bought a new gasket from group1autoparts.com However, as mentioned earlier, I realized I could have reused the casket. It's not the paper/cork jobs of previous years, its a reinforced rubber unit. Pretty beefy if you're careful. Careful reading of the service instructions indicate that the unit can be refilled to the bottom of the fill hole. As always, be sure to remove the fill plug before taking the cover off so you ensure the ability to refill the unit after draining it out.

Posted

 

 

Thanks again. Woukd you happen to know the service intervals for the rear diff?

 

 

Sent from my Z30 using Tapatalk

Depends on the usage, but 50k miles if used hard, or if no towing 100k.

Posted

Thanks. I only tow twice a yeae., 60 km round trip. Will do.it at 75,000 miles.

 

 

Sent from my Z30 using Tapatalk

Posted

 

 

Depends on the usage, but 50k miles if used hard, or if no towing 100k.

Planned to change mine @ 70K mi.s since last done. Bought synthetic, gasket.

Checked oil. Pristine...could have put it back into bottles & sold as new.

I'll wait a while.

Posted (edited)

Skip the cleaner. Just drain and refill. This isn't a major contaminated area. All will be fine. You risk more by trying to clean it out and having a dry spot on the bearings and gear set when you go to move the vehicle. Best to leave it alone and have a fluid film on everything until the fresh gear oil can lubricate everything.

Edited by Black02Silverado
  • Like 1
Posted

Yep I agree with Black02Silverado. Back in the day (and even today) some guys liked to run kerosene or diesel through the crankcase to "clean it out". No thanks! I've never done this to an engine, trans, or diff.

So, is that gasket reusable on the '07 new body G80?

 

I changed the oil at 40k by vacuuming it out of the fill hole 5 years ago. I didn't have a gasket on hand and didn't feel like running around trying to find one at the time. If I can reuse it, I'll be more inclined to change the oil when it's needed. :lol: I like pushing Amsoil to it's limits ...

Posted (edited)

The gasket is a metal lined rubber gasket that is reuseable. I am gonna pick one up though, it my only vehicle. Better safe than sorry.

Edited by WilliamBos
  • 6 years later...
Posted

I replaced fluid on my 2011 sierra 1500 wt 2 wheel drive at 120k mi for the first time.  I bought a new gasket and 3 bottles of AC-DELCO fluid from a dealership because I didn't know if after-market fluid works ok for my truck.  old fluid was totally black and burnt.  a shot glass full of metal powder was inside.  Gear surfaces looked all in good condition.  the truck has been a commuter vehicle with no towing or heavy load.  After the fluid change, I did a 500 mi long trip in one day with no issue.   I plan to do another fluid change at 180k mi or so.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • Whoever greenlighted the work truck matte black front bumpers on every trim but the AT4X should be fired!  I was hoping that was an AI mistake, but just realized they were on every model of the 2027 Silverado too.     Some parts of the interior do look premium, but the Denali Ultimate dashboard looks like an afterthought.  At least they appear to have lost the microfiber the high end Silverado models showed, but the '27 High Country dash looks better than the Denali.  
    • New member here. I am researching a read-first event-recorder concept for late-model GM V8 trucks. This is not a sales post. There is no product link, price, preorder, or mailing list. I am trying to determine whether the underlying problem is real before building anything.   Has your truck ever had a brief problem such as: - rough running or a momentary misfire - an oil-pressure warning or unusual pressure event - reduced power or a brief stall - a U-code or lost-communication problem - a symptom that disappeared before the dealer or independent shop could reproduce it   If so, I would appreciate the following details: - year, model, engine, and mileage - what happened and under what conditions - whether a DTC and useful freeze-frame data were stored - whether the shop was able to reproduce it - what the eventual confirmed repair was, if known - what additional information would have helped the diagnosis   The concept being evaluated is a removable leave-in recorder that continuously retains a rolling window from before and after an event. It would not tune, reflash, clear codes, or change the vehicle calibration.   I am also not claiming that it could predict lifter failure or see every internal ECM variable.   The real question is whether continuous event history would add enough useful evidence beyond freeze frame, GDS2, and existing scan tools — or whether it would simply be another unnecessary gadget.   For owners and technicians, which problem would make something like this genuinely useful: 1. intermittent misfire or AFM/DFM-related behavior 2. oil-pressure events 3. lost communication or electrical faults 4. none of the above Please be blunt. Negative feedback is just as useful as positive feedback.
    • No tears over the SLE and SLT trim levels disappearing but I kind of loathe the "Elevation" name. It's a truck--skip the elegance.   The slab-dashboard design is decidedly different. Almost has a Hummer flavor to it. "Professional Grade" seems to be leaning very white-collar, tech-driven these days moreso than blue-collar, functional design.   The Silverado would be my choice between the two new trucks. Pleased with the engine lineup in both. The GMC is a little "too much" for a truck, IMO, and the Denali borders on ridiculous - but I do know there are buyers for luxury trucks out there. It's just not my speed.
    • Your safety is of utmost importance, @joshua1221, and we understand the importance of having all your lights working in your truck. If you have not already, we highly encourage you to bring your concerns to the attention of your local GM dealer. They are in the best position to diagnose your concerns as well as confirm the compatibility of the mirrors with your truck. Additionally, we would like the opportunity to explore any way we may be of assistance. When you have a moment, please visit: https://s.gm.com/support-request and fill out the support request form with all pertinent details. This form helps our team gather the right information and ensures your request is routed appropriately.
    • - I like the outside but not as much as the Chevrolet.  They ICE'd the EV styling and it works, but I think exterior goes to Chevy on this one.     - SLE and SLT dead = Not.  Surprising.  Fits into the rest of the GMC lineup like this which (aside from Pro) matches the rest of the family.  Elevation, AT4, Denali.     - Interior.  Sophisticated Malaise era.  Why do I say Malaise?  Drawn with a ruler.  Rectangles everywhere.  Looks very premium though.    
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...