Jump to content

Off Road Pictures

amxguy1970

By amxguy1970
in Hobbies, Tech & Outdoors

Recommended Posts

RyanbabZ71 Senior Enthusiast

RyanbabZ71

Posted
Posted

There are threads for particular colors, general pictures and lifts/levels, what about pictures out in the country or off road? If you have some post them up. Eventually I will, going to do some back country mountain pass trips later on in the rockies, then Big Bend and probably PINS among other places. In the meantime, lets see where you have taken these trucks (or if they are dirty).

 

BTW, might make another thread for towing/hauling; haven't searched for that one yet if it has been done, if not might make a thread for those pics as well. Nice to see the trucks doing some work, some other forums have some nice threads covering all those topics and thought the 2014+ trucks would enjoy a thread as well.

 

Tyler

There is a towing thread already check the trailer/hitch section

  • Replies 37
  • Created
  • Last Reply
BHolland Enthusiast

BHolland

Posted
Posted

No I did not have to trim studs. My factory wheels have "pockets" in them for the remaining 1/2" of factory stud to fit into. I did have to do some fender trimming though.

Good to know. Thanks I'll need to check mine for the pockets. I don't really want to go 1.75 if I don't have to.

barry G Senior Enthusiast

barry G

Posted
Posted

spring day snow.

seems mellow offroad in these modern times..

 

post-139084-0-22303700-1459830560_thumb.jpg

 

cost is wild isn't it. I used to see many of the offroad, big bouncing treads..

all quiet.

 

I still find a trail, maine has a few.

Tires are LT all terrain T-rated.

120 capable on the highway and just fine for this stuff.

First I had ever seen on 31.6 inch. Amazing stuff out there..

 

about a mile in on this one.

 

not a sound.. but me.

post-139084-0-22303700-1459830560_thumb.jpg

post-139084-0-22303700-1459830560_thumb.jpg

post-139084-0-22303700-1459830560_thumb.jpg

  • 3 weeks later...
  • 2 weeks later...
  • 2 weeks later...
LTZcoog Enthusiast

LTZcoog

Posted
Posted

Truck catching some rays after a day of rain in Houston

post-152723-0-02068200-1463771670_thumb.jpeg

post-152723-0-02068200-1463771670_thumb.jpeg

post-152723-0-02068200-1463771670_thumb.jpeg

post-152723-0-02068200-1463771670_thumb.jpeg

dcrouse Enthusiast

dcrouse

Posted
Posted

Least there is some people on here not scared to get their truck dirty. Didn't think was any of that went on around here

 

 

Sent from my iPhone using Tapatalk

GPGuy Senior Enthusiast

GPGuy

Posted
Posted

Least there is some people on here not scared to get their truck dirty. Didn't think was any of that went on around here

 

 

Sent from my iPhone using Tapatalk

 

Stick around.. you might be surprised.

GPGuy Senior Enthusiast

GPGuy

Posted
Posted

As in

 

 

Sent from my iPhone using Tapatalk

 

As in there are a number of guys who do take their trucks off roading.

dcrouse Enthusiast

dcrouse

Posted
Posted

 

As in there are a number of guys who do take their trucks off roading.

Hopefully more post up cuz seems only see them shiny lifted street riders lol

 

 

 

Sent from my iPhone using Tapatalk

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Another JR
      Parking Brake - Automatic Engagement Questions

      By Another JR · Posted

      On 2021 3500hd it consistently sets automatically when selecting park if the incline/decline is above a certain angle. 
    • Policeoff01
      Feeling Vibration and Jiggles in 2024 HD Gasser Steering Wheel

      By Policeoff01 · Posted

      Curious, did anyone ever get a fix for the vibration reported here.   I have a 2024 Silverado with 6.6 duramax.   I’m noting the same vibration resonating up through the steering shaft into the steering wheel.    Best way to describe- like someone is tapping on the steering shaft/components and it’s resonating into the steering wheel.    thanks. 
    • Gkistler
      2015 Sierra Denali L86 cyl 5 misfire at idle

      By Gkistler · Posted

      Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • zibzer2
      Pulsating Noise 4Cyl Mode

      By zibzer2 · Posted

      2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Chuck FB
      Some Assembly is Required

      By Chuck FB · Posted

      Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...