Jump to content

Beat to death mirror wiring....

Chango42

Recommended Posts

Chango42 New Member

Chango42

Posted
Posted

Ok, I have a early 15 HD that had small non tow mirrors. I stole the mirrors and door harnesses from a 16 truck we have at work. I jumped the running lights wire, an everything worked fine.

 

Well, we hired a new guy... and he noticed that the 16 didn't have the mirrors it should, with the options the truck is equipped with.

 

So I swapped him the original door harnesses back. He bought his own mirrors.

 

I kept the GM mirrors, but have the early build HD door harness. I watched many YouTube videos.. guy named Phil on there seemed to make harnesses that could make this work for me..? He says he's on here..

 

Any help?

post-176188-0-94911900-1502505724.jpg

post-176188-0-94911900-1502505724.jpg

post-176188-0-94911900-1502505724.jpg

post-176188-0-94911900-1502505724.jpg

newdude Senior Enthusiast

newdude

Posted
Posted

Early build 2015 HD need the RZY harness 23387133 and then new door harnesses. The RZY harness completes the lighting circuits in the truck for the mirror lights to all function properly.

Chango42 New Member

Chango42

Posted
  • Author
Posted

Thanks.. is there a way to just add wires from the mirror plug in the door harness to where it connects in the door jamb ? Instead of buying a whole new harness?

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • SwitchBladeSierra
      HELP! DUMPING COOLANT

      By SwitchBladeSierra · Posted

      If anyone lands here looking for an update - the problem wasnt with the hose, the clamp, etc... I purchased a metal Thermostat housing that just must not of been made to spec. It just wouldn't plug up the hose.. Went back to a plastic cheap housing - leak fixed. Some plumbers tape carefully placed in tandem with a clamp likely would've gotten the job done.   Best,
    • SwitchBladeSierra
      AUX switch install

      By SwitchBladeSierra · Posted

      For anyone following, this is what I have deduced from this forum - and my very specific niche case. Please do let me know if you see me going in the wrong direction here. For context, I have a 16 sierra 1500 w/t. Has TC and Cargo light switches. Removed the switch to find the X1 and X2 of the S48A connection populated with wires (x1 10-14, and x2 1-5).   Took photos of the X61A-X5 to find the wires from S48A-X1 land here at their respective pins (10, 11, 17, 23 on the X5). Was hopeful that this means my X51A fuse box has the appropriate pins... No cigar. So now I will be routing wires from the rear of the X61A-X1 to the engine bay and to their respective negative relay triggers. Please see to the diagram. If any has insight as to where the S48A-X2 pins 4 and 5 land that would be awesome.   Note: please disregard fuse sizes. Main fuse will like be 25A, all mini bus fuses will likely be 10-15A   Cheers
    • Grumpy Bear
      Sugar Bears 2015 GMC Terrain SLE-2 2.4 AWD

      By Grumpy Bear · Posted

      287,500 Mile Service   8/13/2026   Reset Fuel Trims   Since the work done in the previous post there was a good improvement in response in all areas except right after a fill up where the LTFT would go -20%+ for about four miles while the STFT was near neutral. Before the work they both went very negative for a few miles after a fill up but act normal thereafter.    We did a systems check of the vapor recovery system for functionality and ability to hold a vacuum. That checked out fine. But this doesn't mean the charcoal canister is dead in the water. Testing that is next up. For now the reset of the fuel trims.    I intentionally shorted the fill exactly two gallons to eliminate any chance of filling the canister. On start up the trims were behaving normally until I got up and rolling where the LTFT went -10 / -11%% but the short was + 2 to 0%. Within a mile the the STFT offset the LTFT and by 2 miles they were neutral. HUGE improvement but still not hunky-dory.    I'll watch them for a few days. Perhaps another tank where I will fill completely to 'first click' and compare. Meanwhile on the hunt for a new canister and I'll toss another purge value at it for good measure. Pending the outcome of the canister test that is. Progress of any kind is welcome.    Fuel economy improvement with bringing hole #3 back to the living was a noticeable bump to the positive. Even on the few miles I drove after the refill I already see another bump up by the trims reset.     She's purring like a kitten with a warm bowl of milk.    BTW, adding 50 rpm to the idle took the majority of the negative timing out on cold start up and leaned the cold idle. No longer burbles in the cat. What a dumb way to heat a cat.      
    • OnTheReel
      Post your UOA, (used oil analysis) here

      By OnTheReel · Posted

      Yeah, shame I can’t really get that filter easily anymore. Running a PureOne. Your fave!    TAN would be neat to see. Confirmation I ran it too long probably. 🤣
    • superdave160
      Roll up bed cover experiences

      By superdave160 · Posted

      My son and I both bought new trucks in 2017. Both of us immediately put Truck Covers USA American Roll Covers on our trucks. My son still has his truck and it never sees the inside of a garage. We live in Alabama, so not much snow. My truck was my daily driver and was in the garage when I wasn't driving it or at work. No issues with either cover even after almost 9 years. About a year ago I sold my truck to my brother and bought a 2025 Silverado 2500. The second thing that I put on that truck was a new Truck Covers USA cover. They are very well made and have a very positive locking system. I looked at a Retrax and my concern was the way that the cover locked to the rail. BTW, the first thing I put on the new truck was step bars. Those new trucks are high!

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...