Jump to content

Recommended Posts

Posted
Finished everything up. Had to make my appointment for the alignment next Friday due to shipment delays. 1.5 motofab & 35 12.50 18 Ridge Grapplers with 2" Bora spacers. 
CD5300A9-68E5-4486-8FA9-0DA005D4C340.thumb.jpeg.e62559380c5bf36f0119e0695ac2921a.jpeg
B14A6733-8643-4D5C-A0DB-A933D4ED4AB5.thumb.jpeg.a04e0a5f12c7c93bb16075d2754ddeb7.jpeg
Any rubbing with this setup? I want something similar when the time comes. So over factory trucks you have the 2" TB lift and then the 1.5" moto for a total of 3.5", how are your cv angles? Any close up pics of suspension parts would be appreciated. Truck look great btw

Sent from my ONEPLUS A6013 using Tapatalk

Posted
2 hours ago, JR09country said:

Any rubbing with this setup? I want something similar when the time comes. So over factory trucks you have the 2" TB lift and then the 1.5" moto for a total of 3.5", how are your cv angles? Any close up pics of suspension parts would be appreciated. Truck look great btw

Sent from my ONEPLUS A6013 using Tapatalk
 

 

Posted (edited)

Thanks definitely loving this setup a lot! So, in front of the front wheels, nothing at all as far as rubbing goes. In the rear of the front wheels, I had some and I found the best way to eliminate it was to remove the bracket behind the fender liner and trim the mudflaps. As soon as I did that, full turn forward/reverse over curbs, etc and I've got plenty of room with no rub whatsoever. I'm doing some finishing sanding on the flaps to make them look factory. No crazy angles but next weekend after my alignment, I'll be checking all my torque values once more and I'll snap some pictures.

Edited by ETMC
Misspelling
Posted



Thanks definitely loving this setup a lot! So, in front of the front wheels, nothing at all as far as rubbing goes. In the rear of the front wheels, I had some and I found the best way to eliminate it was to remove the bracket behind the fender liner and trim the mudflaps. As soon as I did that, full turn forward/reverse over curbs, etc and I've got plenty of room with no rub whatsoever. I'm doing some finishing sanding on the flaps to make them look factory. No crazy angles but next weekend after my alignment, I'll be checking all my torque values once more and I'll snap some pictures.


Awesome. Thats not bad at all if all you had to do was remove the bracket and trim the flaps.

Sent from my ONEPLUS A6013 using Tapatalk

Posted

Zone has a 1.75" leveling kit. has anyone bought this kit? I'm thinking this is the lift i will go with.

 

http://zoneoffroad.com/1.75-Leveling-Kit-2019-Chevy-TrailBoss_and_Sierra-AT4/c1171

 

1.75" Leveling Kit

 

Here's some of the information.  

 

  • 3-piece design with top mount spacer and 2 preload spacers to raise ride height without over-extending suspension during droop travel
  • Maintains ride quality and handling characteristics
  • Allows clearance for 33-34" tires
  • Includes Factory Protection Plus

 

Zone Offroad is now offering leveling kits specially designed for the 2019 Chevy Trail Boss and GMC AT4 trucks. Engineered to be more than just a "budget boost", these kits are designed to a higher standard to work within the parameters of the factory suspension and steering geometry to maximize its potential while allowing clearance for larger tires. As with all Zone Offroad lift kits, these new kits are backed by Factory Protection Plus for piece of mind wherever your adventures may take you. Factory Protection Plus includes Zone Offroad's Limited Lifetime Warranty, ESC system compliance and a 5-year 100,000-mile drivetrain warranty.

Important Notes!

  • 1. Strut compressor required for installation.
  • 2. Will not fit Adaptive Ride Control (ARC) equipped models.
  • 3. Tires wider than 295/ cannot be installed on factory wheels due to clearance issues to the steering knuckles.
  • 4. Welding required to install optional LCA steering stops.
  • 5. Complete 1.75" leveling recommended for AT4, Trail Boss suspension not as raked for the factory so installing without thin preload spacer will net 1-3/8" lift for a level stance.

 

Hope this information helps. 

Posted
On 7/14/2019 at 5:58 PM, Sin City Trail Boss said:

If I remove the rear block on my TB, what do I replace it with to level it with the front?

Smaller block and U Bolts. A show here in town just told me they had another Trail boss do that and it leveled the truck. You'll need smaller U bolts

 

Posted
On 7/14/2019 at 7:10 AM, ETMC said:

Finished everything up. Had to make my appointment for the alignment next Friday due to shipment delays. 1.5 motofab & 35 12.50 18 Ridge Grapplers with 2" Bora spacers. 

CD5300A9-68E5-4486-8FA9-0DA005D4C340.jpeg

B14A6733-8643-4D5C-A0DB-A933D4ED4AB5.jpeg

When you have time, could you please take a couple pics from straight-on front and back? I'd like to see how far the tires stick out from the fenders. Also, in your estimation, do you think you could get by on 1" spacers?

  • Like 1
Posted

^^I hope your going to put flares on that truck, otherwise kiss your paint good-bye. GM's post-2010 paint is not up to the task of beings pelted with rocks and sandblasted daily.

Posted


3583160b43cbb4241525ddd8ee61a7cf.jpg

Here’s my alignment sheet from this morning. Hope it helps.
Please tell me what I'm looking at. This good or bad? I see green..

Sent from my Pixel 3 XL using Tapatalk

  • Like 1
Posted
On 6/10/2019 at 8:10 PM, jtl1985 said:

so what does everyone run for tires with the leveling kit on a trail boss lt? I ordered the understrut kit and prefer to have a little bigger tire. keeping the 18's but do I go 33" or bigger without rubbing issues? I've always had to trim and I really don't want to this time, maybe just he mud flap if I have to.

i run a 33x12.5 on 20s with my trailboss

  • 5 weeks later...
Posted
On 7/15/2019 at 11:47 AM, Bizar said:

Zone has a 1.75" leveling kit. has anyone bought this kit? I'm thinking this is the lift i will go with.

 

http://zoneoffroad.com/1.75-Leveling-Kit-2019-Chevy-TrailBoss_and_Sierra-AT4/c1171

 

1.75" Leveling Kit

 

Here's some of the information.  

 

  • 3-piece design with top mount spacer and 2 preload spacers to raise ride height without over-extending suspension during droop travel
  • Maintains ride quality and handling characteristics
  • Allows clearance for 33-34" tires
  • Includes Factory Protection Plus

 

Zone Offroad is now offering leveling kits specially designed for the 2019 Chevy Trail Boss and GMC AT4 trucks. Engineered to be more than just a "budget boost", these kits are designed to a higher standard to work within the parameters of the factory suspension and steering geometry to maximize its potential while allowing clearance for larger tires. As with all Zone Offroad lift kits, these new kits are backed by Factory Protection Plus for piece of mind wherever your adventures may take you. Factory Protection Plus includes Zone Offroad's Limited Lifetime Warranty, ESC system compliance and a 5-year 100,000-mile drivetrain warranty.

Important Notes!

  • 1. Strut compressor required for installation.
  • 2. Will not fit Adaptive Ride Control (ARC) equipped models.
  • 3. Tires wider than 295/ cannot be installed on factory wheels due to clearance issues to the steering knuckles.
  • 4. Welding required to install optional LCA steering stops.
  • 5. Complete 1.75" leveling recommended for AT4, Trail Boss suspension not as raked for the factory so installing without thin preload spacer will net 1-3/8" lift for a level stance.

 

Hope this information helps. 

I am having this kit installed tomorrow with TOYO MT 295/70R18’s on factory wheels.

  • Like 2
Posted
8 minutes ago, CDub said:

I am having this kit installed tomorrow with TOYO MT 295/70R18’s on factory wheels.

Before installation 

246C165D-F870-43EE-BE97-2719E351F9F1.jpeg

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Lake Speed is drumming up business for his company just by being in the spot-light so he has a vested interest in stoking the 0W-20 fire.  IMO  
    • I knew when I bought my truck that it had off road hill decent or craw control or whatever they call it and rolled my eyes at that but it gets throw on with other options my truck has, I just never had a heads up if the highway speed regular cruise setting had anything to do with the brakes and that took me by surprise. If you've ever been to the top of Pikes Peak and watched those ahead of you on the way down with their brake lights on constantly, one can guess they are probably not gearing down or not enough anyway if their vehicle will allow and a good reason their is a brake check spot part way down where they use an infra red heat gun to check how hot ones brakes are front and rear.    Your right that once one gets out of the front range by Denver and I've not been on that stretch of 285 between Denver and Fairplay myself but I know its high and Fairplay at 10000 feet, Buena Vista at 8000, it drops a bit from there but then your going back up and over the 11000 pass and Durango is at 6500 . So yes your definitely right that 6500 and a lot higher is the theme of going anywhere out in that direction from Denver but hey, the down hill sections give fantastic fuel mileage !.    I don't even look at the fuel pumps for what premium costs here, since I live on a farm and up to this point get fuel delivered I am rarely in front of a fuel pump and when I am, I am often using card lock bulk fuel stations so it tells me what the price is AFTER I buy the fuel. Looking up on gas buddy and converting to US gallons but in Canadian dollars, regular on average of the prices listed was around 5.95 and premium is around 7.00 . That was one reason I did not go for the 6.2 half ton aside from its lack of carrying/towing if one was going by the rule of using premium fuel and until recently one could only buy regular farm gas if playing the few cents off game for farm dyed fuel for a "farm licensed pickup". But yes I hear you on the fuel price difference and like the diesel theme with it often being more expensive then gas it doesn't have quite the charm to it either as it once did although right now here for some reason the price of diesel has come down more so its now inline with the price of regular gas. 
    • I agree with this assessment. As you know I’m testing longevity with vehicles for the first time. I have a few vehicles I passed to kids and grandkids. We’re all past 100K miles some approaching 170K. I’m the only one doing 5k oil changes. The rest whatever the minder says. I’m the only one doing frequent transmission service. My odyssey the trip vehicle at 200K will be finished as a trip vehicle. I recently changed to high mileage oil, Valvoline. I can’t get past the fact that all manufacturers want to claim long service life. I just don’t make sense that they would go with low weight oil for mileage. While sacrificing longevity.
    • There's absolutely a mountain of profit in catering to the "I do my own research" crowd, people who are certain they know better. And I don't mean there isn't data to support that 0w40 produces less wear product than 0w20 in an engine like the 3.0 Duramax, that only feeds them the assurance they need. Again, my whole thing with oil selection is, sure, 0w40 or 0w30 produces less wear product. Are we talking the difference between the engine lasting only 100k versus 200k? Or are we talking more like, if the engine will already go 350k on a good 0w20 regimen recommended by the OE, is using 0w40 going to get us to 355k, assuming we can even get the rest of the truck to last that long, meanwhile sacrificing the first 5y, 100k in powertrain warranty. The answer isn't easy, there are tradeoffs.   I willfully use 0w20 Dexos D for this reason, knowing that a 0w40 will produce slightly less wear. I don't believe the delta in wear product is meaningful over the lifetime of the engine, and I place much more importance on driving style and overall feeding and care of the engine as a whole. It's the mentality that someone can abstain from alcohol their whole life which is an amazing boost to health by itself, theoretically. But if they're sedentary, that lifestyle choice will most likely kill them young despite their other, concerted efforts. Maybe someone doesn't drink AND they are the perfect picture of health and activity AND they use 0w40 AND they treat their engine perfectly. If living until 130 years is the goal, sure, do that. But it's going to be a really old truck falling apart around a good engine for that last 30 years, without a doubt.   I watched Demonworks' other video on the 100k+ 3.0 Duramax that had dealer 0w20 changes on what appears to be OLM-prescribed intervals (8-10k).   The QR codes are still present and readable on the main bearings. That's how little wear it has.   That's not proof that anyone else should stick to 0w20, but it's confirmation, for me, that 0w20 is perfectly acceptable to use in these engines.
    • 1Based on independent testing of OE 0W-20 in the Peugeot TU3M Wear Test as required by the dexos1 Gen 2 specification.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...