Jump to content

leveling a trailboss

mfbearded
 Share

Recommended Posts

Mike may New Member

Mike may

Posted
Posted

The control arms where stock, just ordered ready lift leveling kit with upper control arms designed to change the geometry of the stress on the components especially the control arm and ball joints

  • Replies 212
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

silveradonationfan15
silveradonationfan15

And that is a leveled trailboss with 35" tires

Ben Berkenpas
Ben Berkenpas

Can't tell if your trying to be a comedian here or if your serious?  It wasn't really very funny and it didn't really make any sense!  If you don't care about this topic, don't follow along.

JR09country
JR09country

To me 2" is 2" no matter how you get it. Wether you put it on the top, bottom or middle it still increases the cv and ball joint angles. Sent from my ONEPLUS A6013 using Tapatalk

Posted Images

ALLSTAR Enthusiast

ALLSTAR

Posted
Posted
1 hour ago, Mike may said:

The control arms where stock, just ordered ready lift leveling kit with upper control arms designed to change the geometry of the stress on the components especially the control arm and ball joints

The only modification i did on my truck was the 1" spacer. Scared the hell out of me when that tire folded and locked up !.

So that's 2 trailboss trucks that failed. It appears factory 2" plus 1" for 3" total is to much upper ball joint angle.

Beware trailboss owners with lift  blocks without upgraded upper a-arms ! .

jgjorge44 Enthusiast

jgjorge44

Posted
Posted
6 hours ago, Mike may said:

The control arms where stock, just ordered ready lift leveling kit with upper control arms designed to change the geometry of the stress on the components especially the control arm and ball joints

Did you get it professionally installed, curious because I wanted to do a RC, level but now I’m second guessing... did you do an alignment after installing too?

jgjorge44 Enthusiast

jgjorge44

Posted
Posted
On 10/12/2020 at 11:25 AM, ALLSTAR said:

Added a Motofab 1" spacer (CH-1LM-TB)  to my 2019 trailboss. after about 8 months passenger side upper ball joint separated.

Normal driving, couple railroad track crossings daily at speed that might have extended suspension.

Lucky i was going only about 25mph when it came apart. Going to go with better angle upper a-arms.

 

IMG_6438.jpg

IMG_6437.jpg

Was your level professionally installed? And did you do an alignment? Curious because I’m second guessing doing it now..

ALLSTAR Enthusiast

ALLSTAR

Posted
Posted
8 minutes ago, jgjorge44 said:

Was your level professionally installed? And did you do an alignment? Curious because I’m second guessing doing it now..

I installed them myself. Its just a spacer, 2 bolts, Its pretty easy to install, you really cant do it wrong.

I could post a pic when it gets light out. Went right to alignment shop and they had to do a minor adjustment.

ALLSTAR Enthusiast

ALLSTAR

Posted
Posted
31 minutes ago, ALLSTAR said:

I installed them myself. Its just a spacer, 2 bolts, Its pretty easy to install, you really cant do it wrong.

I could post a pic when it gets light out. Went right to alignment shop and they had to do a minor adjustment.

Here is closer view of ball joint

IMG_6512.jpg

IMG_6513.jpg

Musgo Enthusiast

Musgo

Posted
Posted

I’m not a mechanic.  Bought my truck new off the lot as it sits today.  Can anyone look at my angles and tell me if I’m driving around a ticking time bomb?  If so I’m going to get my suspension fixed.  
 

41CBE918-A36C-492C-BF9D-951EBB819D7D.jpeg

986D4B5B-4C2D-4B89-9378-A224714E3302.jpeg

jgjorge44 Enthusiast

jgjorge44

Posted
Posted
9 hours ago, Musgo said:

I’m not a mechanic.  Bought my truck new off the lot as it sits today.  Can anyone look at my angles and tell me if I’m driving around a ticking time bomb?  If so I’m going to get my suspension fixed.  
 

41CBE918-A36C-492C-BF9D-951EBB819D7D.jpeg

986D4B5B-4C2D-4B89-9378-A224714E3302.jpeg

From my understanding is that every stock is already stretched, but still good if you keep factory settings on it. You only push it if you plan on leveling, if so the consensus seems to be to replace the arm to fix the geometry. Readylift has a kit that includes the arm. 

ALLSTAR Enthusiast

ALLSTAR

Posted
Posted
1 hour ago, jgjorge44 said:

From my understanding is that every stock is already stretched, but still good if you keep factory settings on it. You only push it if you plan on leveling, if so the consensus seems to be to replace the arm to fix the geometry. Readylift has a kit that includes the arm. 

I agree. MUSGO'S AT4 appears to be factory, and looks good to me .  Can someone with just a 1" or 1.5" level with factory upper a arms get a picture of the ball joint angle like the one Musgo posted for a comparision ?  

jgjorge44 Enthusiast

jgjorge44

Posted
Posted
1 hour ago, ALLSTAR said:

I agree. MUSGO'S AT4 appears to be factory, and looks good to me .  Can someone with just a 1" or 1.5" level with factory upper a arms get a picture of the ball joint angle like the one Musgo posted for a comparision ?  

RC’s level is 1.5in but it still apparently caused the same issue. I guess replacing the arm is the only way to fix the geometry, but I don’t know for sure. I would like to see someone’s geo with a professionally installed level, see if it’s still the same. Also some Chevy dealers preload a 1in level on their trucks off the lot. Would like to know where they get their kits 

Musgo Enthusiast

Musgo

Posted
Posted
7 hours ago, ALLSTAR said:

I agree. MUSGO'S AT4 appears to be factory, and looks good to me .  Can someone with just a 1" or 1.5" level with factory upper a arms get a picture of the ball joint angle like the one Musgo posted for a comparision ?  

Only reason I’m concerned is the truck came with 285/65 20s.  So I was worried there was a level the dealer added to do so.  

BEnax Enthusiast

BEnax

Posted
Posted
On 10/26/2020 at 12:59 PM, Mike may said:

The control arms where stock, just ordered ready lift leveling kit with upper control arms designed to change the geometry of the stress on the components especially the control arm and ball joints

Hello I have a 2020 at4 with the 1.75” leveling kit with control arms. On these trucks they recommend control arms with a leveling kit. To keep all the angles right for the cv axel joints etc. I’ve had it in for about 2 months now. Zero problems at all, truck might even ride better. I also have the truck sitting on 22x12 -51 offset with Toyo 33x12.5 

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Why don't I have a good scanner? I've always wanted one when I've needed one.   My latest reading says I don't need to do a relearn on the ckp sensor on a 1995 with OBD 1.5. The relearn is prescribed for the later-model 1995's which shipped with actual OBD II when GM completed the transition in prep for the 1996 MY. I need to confirm that. Did you know forums are disappearing? Knuckleheads on Facebook... it's not the same. It's just not.   So, scanners. Again, shooting myself in the foot for having eBayed my Snap On MT2500 "brick" with all the adapters. Not that I couldn't buy another but those are getting quite old, and mine wasn't new enough to work on 2000's vehicles.   Damn it (as I'm scanning my email between paragraphs here). Did you know there's a 2000 Jimmy 2-door on BaT that's ending this morning? It's local. I want it. 14k miles. Absolutely beautiful.   Back to scanners. MT2500's are old. Solus, now that could be a contender. There's a ~2008 Verus with a system error that's basically new in box for cheap. Hmm...I'm not sure about a scanner that runs an archaic version of windows (95 or CE, I can't tell).   I want the ability to reset and rotate TPMS, test individual modules, bleed ABS, electronic parking brake controls for servicing brakes, relearn procedures and other bidirectional controls.   Snap On does an MT2600. It's a new model as of last year, marketed as their "entry" scanner. Entry? Only where $1900 gets you through the doorway plus, I'm guessing, $1000/year if you wish to keep it current. So goes scan tools actually designed for production environments. Want decent products with excellent support, you pay for it.   Everyone is raving about Autels and TopDons and Foxconns and all these newer brands that are selling the $500 "prosumer" scanners for backyard hacks like me. They're tempting...honestly. Updates are cheaper, base prices are remarkably cheaper... And you get to deal with bugs and translation whoopsies and, well, just don't use it on anything expensive, OK? Having a dealer replace an ECU because it needs to be re-imaged after an adventure in scanning is no joke. But I think most people are getting by OK with these units.   eBay on a scratch-and-sniff pro-model oldie, a shiny new TopDon, or???   God dang it, I can't stop looking at this Jimmy. I'm ready! I'll Bring The TRailer! It's beautiful.
    • Texasdeere
      What have you done to your K2 today?

      By Texasdeere · Posted

      I removed the OE running boards.  It looked so much better.  I wish I took them off a long time ago.     I had to put something back on for my wife.  I wanted Westin Sure Grip Running Boards but they are very pricey, like $600 plus.  I was going to go with the Ionic 41's like I had on the 2019 Silverado but went with Westin Outlaw Drop Steps instead, about $200 cheaper.  They are sturdy and functional but not super crazy about the look, but it works.  
    • Atlas
      Gas Prices

      By Atlas · Posted

      It's all a crock of 💩
    • fondupot
      Disable DRL's

      By fondupot · Posted

      I had a Gen5DIY DRL relocate harness from a 2022 1500 that I saved. I had Gen5DIY modify the harness for my 2024 Silverado 2500. Plug n Play, worked perfectly.    Here's a video I made for the 2022 1500 truck. The install is more or less the same on a 2500.    The harness relocates the DRL tot he top amber turn signal on my 2500.     
    • CamGTP
      Gas Prices

      By CamGTP · Posted

      Can ask that about a lot of places.   Holiday sells 91 for $1 over 87 octane. BP 93 is 80 cents. Amoco 93 is 80 cents Kwik Trips is $1.20 for 92 or whatever they have and $1 for the 91.   I know that this is not exactly same as what you are saying with the premium to premium debate of those two stations but why is there such a difference. Top Tier this and that, it's all BS. All the fuel comes from the same damn refinery, so give me a break.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...