Jump to content

Recommended Posts

Posted
19 hours ago, Grumpy Bear said:

 

Valvoline Daily Protection Mineral SAE 30 100 C viscosity, 10.3 cSt. 100 C HS viscosity 10.3 cSt (ASTM D6616)

Warren Oil (COSTCO) Full Synthetic 5W30 100 C viscosity 10.9 cSt 100 C HS viscosity 8.1 cSt @ .84 SG or 6.9 cP

Multigrade exhibits a 27% viscosity loss. Temporary shear down to SAE 20. 

I've shown the receipts before. Entire data sheets for both oils. Not posting them again. 

 

A shelf Synthetic 5W40 under ASTM D6616 conditions would, for most shelf oils, act as an SAE 30 at temperature and imposed shear levels of towing. Your brother skins the cat to the same end as I, just a different way. Bully for him! 

I’m looking at best in class straight 30 for my “new” 1974 IH D200 4x4 345 V8 that has gears instead a timing chain and 61,500 original miles. Currently running Amsoil signature series 10w-30 but I need to stop some leaks. 
Conklin Convoy 30 

Schaeffer 30 

Valvoline VR1 30 syn or conventional 

Valvoline Daily Protection 30 

Any other suggestions? 
 

IMG_0126.thumb.png.d2ea5c46b21d12ae6be7e9c570200ba3.png

Posted (edited)
3 hours ago, txab said:

So the M1 A1 Abrams tank is running good these days?

Always has run like a turbine powered tank.  I just can't drive it since left leg is not allowed to clutch yet......

 

Edited by customboss
Posted (edited)

Can you imagine the beginning of time? Perhaps the end of time is easier? No? That's an exercise in logic. 

 

Referee tosses a coin, a quarter, you've never seen. It comes up tails. Does it have a date on the obverse side? That's an exercise in reason. 

 

Science is a process that leads to a conclusion that at best proclaims our best CURRENT understanding. Some of those have lasted for seconds. Some have lasted for hundreds of years. Science is NOT the conclusion. Just the process. 

 

Facts are the conclusions of science, logic and reason we can not seem to poke a hole in. Everything else is in a state of flux. Theory. It's called the Theory of Evolution, for a reason and yet taught as a FACT. And example of how theory gets used to promote an idea the facts do not support. 

 

So I'm a bit stunned that a guy who prides himself in the practice of science finds it odd that at times we can reject what the process points to but has not yet lasted long enough to be considered a fact. Or has proven to be in flux over decades so as to not have reached a conclusion we may rightly call a fact.  

 

I'm amused that a fellow such as this does not seem to understand the methods of marketing for twisting facts to suit an end to which he has been a partner to himself. Eagerly or unwittingly it makes no difference. It is a yardstick he chooses to condemn others with. Only perfection can judge imperfection. :idiot:

 

Imagine for a moment being confronted with a job that demands a conclusion the facts do not support for whatever reason there may be. Greed, politics, notoriety...whatever that case may be some fabrication of facts, twisting, cherry picking while posing as science will be demanded of that fellow if his end is to be met.

 

Knowing I have him "Ignored" and am unlikely to see those words, he is emboldened to speak as if he knows me. There is some character. Some first rate moral backbone. Coward. 

 

Reason, logic and yes science that is unadulterated are my tools and yes, that means I will reject things that are pretending to be science that are not or that are that have not reached a reasonably mature conclusion. 

 

Science has been studying ZDP for about 100 years. Late 1930's and in the 1950's it became prevalent in commercial use. To this day science is unsure of how it works, why it works and all the factors influencing its effectiveness. Initially it wasn't even used as an anti-wear additive. That was OBSERVED and not a part of the scientific study. Most of what we know that makes it useful is by applied observation much like poking a frog in the butt with a stick and watching it jump and reaching the conclusion that a poke in the butt makes frogs jump. Science has provided useful relationships that permit manipulation of it without actually knowing it. I don't need to know the deepest innerworkings of a landmine to appreciate someone telling me where they are in the field so that I may benefit from that knowledge. 

 

I am not bitter with former bosses. I am beholding to them. That they recognized my ability provided me with opportunities in my field denied those with higher paper credentials and less ability to execute what they knew. One of many lies told about me.   

Edited by Grumpy Bear
  • Sad 1
Posted (edited)
9 hours ago, Grumpy Bear said:

Knowing I have him "Ignored" and am unlikely to see those words, he is emboldened to speak as if he knows me. There is some character. Some first rate moral backbone. Coward.

You IGNORE me and I am a coward?  Struck a cord there eh?  Awe that hurts.  Not from a conscientious objector like you. Who's the coward? 
 

image000000.gif.a111b77e1ba811609a2fe2f73ffd94fd.gif

 

 

Edited by customboss
  • Haha 2
Posted
23 minutes ago, customboss said:

You IGNORE me and I am a coward?  Struck a cord there eh?  Awe that hurts.  Not from a conscientious objector like you. Who's the coward? 
 

image000000.gif.a111b77e1ba811609a2fe2f73ffd94fd.gif

 

 

As usual his word count is lengthy, but doesn't actually say anything.

  • Thanks 1
Posted

In other news, power has not yet been restored. Not that it would matter...still need to have our main panel assessed. Will be working on that as soon as business hours start here this morning. The gas generator will need to come out of service this afternoon for maintenance. I don't want to run it over about 50 hours without an oil change. Last year we went a little over 75 and the oil was extremely dirty. That's the longest we've ever run it. It's 20 years old and only has about 260 hours on it.

 

Chargepoint is sending us a new EV charger, no cost. Surprisingly, it is still under full warranty after 2 years. They agreed that was unusual behavior. We had to send them detailed pictures of the install. It all checks out. Thumbs up for good warranty coverage AND support on a Sunday.

  • Like 1
Posted (edited)
21 minutes ago, Atlas said:

In other news, power has not yet been restored. Not that it would matter...still need to have our main panel assessed. Will be working on that as soon as business hours start here this morning. The gas generator will need to come out of service this afternoon for maintenance. I don't want to run it over about 50 hours without an oil change. Last year we went a little over 75 and the oil was extremely dirty. That's the longest we've ever run it. It's 20 years old and only has about 260 hours on it.

 

Chargepoint is sending us a new EV charger, no cost. Surprisingly, it is still under full warranty after 2 years. They agreed that was unusual behavior. We had to send them detailed pictures of the install. It all checks out. Thumbs up for good warranty coverage AND support on a Sunday.

I run my generator one hour every other month. I have a detached garage, it’s next to our outside freezer so I plug that in. I made an exhaust pipe extension to run outside the garage. I have a 50ft plug the electric company made that plugs into my electric panel. It has a manual switch that only works if I turn off the feed from the road. They all have fancy names I forgot. I needed one time for ten hours during a hurricane. So it’s run more as practice than actual needed. It will run almost everything some not all at once. Most of my family have whole home generators. My setup costs about a third of their setup. If my generator fails I have many outlets to replace the unit in a matter of hours . My mother’s whole home went down. It took 3 days for service. So much for frozen foods. I run two freezers. If my garage was attached I would have built a little cover for the generator. 

Edited by KARNUT
  • Thanks 1
Posted
18 minutes ago, Atlas said:

In other news, power has not yet been restored. Not that it would matter...still need to have our main panel assessed. Will be working on that as soon as business hours start here this morning. The gas generator will need to come out of service this afternoon for maintenance. I don't want to run it over about 50 hours without an oil change. Last year we went a little over 75 and the oil was extremely dirty. That's the longest we've ever run it. It's 20 years old and only has about 260 hours on it.

 

Chargepoint is sending us a new EV charger, no cost. Surprisingly, it is still under full warranty after 2 years. They agreed that was unusual behavior. We had to send them detailed pictures of the install. It all checks out. Thumbs up for good warranty coverage AND support on a Sunday.

Win win and if broad based outage with trees it might take a bit.   We burned here in Forbes Park CO in 2018 when a drunk mentally defective immigrant from Denmark had wind move his illegal trash burning and literally ruined one of the most pristine 15,000 acres in southern CO.  Spring Fire, look it up.  We now have dead trees falling all over the place especially when wind picks up to 80 mph+ which at 9000'-11000' msl not unusual. Takes power lines out quick.  

  • Sad 1
Posted
3 minutes ago, customboss said:

Win win and if broad based outage with trees it might take a bit.   We burned here in Forbes Park CO in 2018 when a drunk mentally defective immigrant from Denmark had wind move his illegal trash burning and literally ruined one of the most pristine 15,000 acres in southern CO.  Spring Fire, look it up.  We now have dead trees falling all over the place especially when wind picks up to 80 mph+ which at 9000'-11000' msl not unusual. Takes power lines out quick.  

Interesting. We call those snags. When we cleared transmission and service lines. We had to remove those. Our local co-op is always out looking for potential hazards to power lines. 

  • Thanks 1
Posted
2 minutes ago, diyer2 said:

I remember that fire custom, so sad. 

We tried to deport him to Denmark and they refused him....LOL  So he's back hiding out around here.  

Posted (edited)

1 Order of magnitude (Nitration)

 

The Boss claims that each integer is one order of magnitude greater than the last. i.e. 11 is one order greater than 10 and 12 is one order greater than 11. Thus 12 is two orders more than 10. Each 10 times greater than the preceding value. 

 

Problem. An order of magnitude isn't defined like that. https://en.wikipedia.org/wiki/Order_of_magnitude

 

So if I start with a base background of 8 abs/0.1mm one order of magnitude is any number between 0.8 and 80 abs. The range of two orders of magnitude for a value of 8 is from 0.8 to 800. This means that 8 is within a factor of 10 from both 0.8 (10^0) and 800 (10^2). Ergo 20 isn't an order greater, its a value within one order as is 80. 2 orders would fall between 81 and 800 before a distinction could even be made between 1 and 2 orders. 

 

Background matters. Oil type matters and they differ. 

https://precisionlubrication.com/articles/detecting-oxidation-and-nitration/

 

 

 

Edited by Grumpy Bear
  • Haha 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • No engine digit "E" for 2019-2026.  Stop reading slop online     All 2026 V8s have functioning DFM.  Hardware and software.  5.3 and 6.2.  The L84 5.3 has "D" as the 8th digit of the VIN, the L87 6.2 has "L" as the 8th digit of the VIN.       If you want a factory DFM disabled 2019-2026, you'd have to find a used 2021 or 2022 chip shortage truck.  The vehicle build data will have a specific RPO code indicating its a factory disabled truck.  RPO code YK9 and only with the L84 5.3 engine.  These still have the hardware installed but are NOT functioning due to the COVID chip shortages that were ongoing.  
    • My post above is the direct reason for my outsized interest in keeping what I have for as long as possible. My memory isn't as short as some. 
    • I don't think so. 😏 Cars? Our experience will diverge there as well. I was buying cars with 200K (1970's) when I started and quite a few were pretty solid cars. (My early stuff was 1964 to 1968)  Some stinkers but not the dismal picture painted above. Now that said, yes, a dealer wouldn't talk to you if your car had more than 60K on the clock and lot cars were 60K or less except the back row where 100-120K was the auction bought for dirt for us poor losers. Kids in my county were not allowed to wear long pants if they couldn't rebuild and repair every part of that beast.    I will agree that many parts are now better. Alternators and charging systems are an envy. But I replaced few water pumps or power steering pumps then. Rebuilt carburetors but replaced few. Mufflers are another place of OEM improvement. Stainless? We didn't have no stink'n stainless.    As long as humans are in charge of governance this $$$$ situation will not improve.    The purchasing power of a dollar in 1955 is significantly higher than in 2025, meaning that a dollar could buy more goods and services in 1955 compared to 2025 due to inflation over the years. For example, what you could buy for $1 in 1955 would require approximately $10.50 in 2025.  Calculator.net inflationtool.com   Comparison of Purchasing Power: 1955 vs 2025 The purchasing power of a dollar has changed significantly from 1955 to 2025 due to inflation. Below is a breakdown of how much more money is needed in 2025 to match the buying power of a dollar in 1955. Purchasing Power Overview Year Equivalent Value of $1 in 1955 1955 $1.00 2025 $10.50 Key Points Inflation Impact: The value of money decreases over time due to inflation, meaning that the same amount of money buys fewer goods and services in the future. Example of Inflation: What could be purchased for $1 in 1955 would require approximately $10.50 in 2025. This illustrates how inflation has eroded the purchasing power of the dollar over the decades. Understanding these changes in purchasing power is crucial for financial planning and assessing economic conditions over time.  Wikipedia Calculator.net
    • The thermometer has been in my wife's 2008 envoy, my sons 2016 chevy, my friends 2020 1500 silverado all showing cooler readings. It's not the guage.
    • Have a question concerning trim levels. Ive not bought a new vehicle since 2006, and I have decided on a 2500 gmc pro or silverado custom. For anyone that has one of these 2 trim levels have you regretted not stepping up to the LT or SLE. I look at things as the more electronics the more problems to arise. I love the look of the old school gauges on the dash as well. Looking forward to hearing your thoughts. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...