Jump to content

Recommended Posts

Posted
On 8/27/2020 at 1:29 PM, Smrtasp said:

What width of a 20 inch wheel and what brand/model? Your offset will depend a lot upon that. Im running a 20x9 Fuel Rage with a +1 offset running a 295/60/20 which is a 34x11.5 tire. Running a 20x10 will be different. A 20x9 with a +12 offset seems a bit pushed inside (positive pushes the wheel closer inward) but the backspacing may play a factor here with the wheel design. A 285/55/20 should fit a stock GM 20 inch wheel so what you are asking for should work in theory.

I will be going with either the Venomrex 601 

Wheel Specs
Size: 20X9.0
Offset: 0 (Chevy/GMC/Dodge)
Backspacing: 5.0" (Chevy/GMC/Dodge)
 

 

Or the Black Rhino Shrapnel

20x9.5

Offset 12

 

 

Posted
1 hour ago, osumason said:

I will be going with either the Venomrex 601 

Wheel Specs
Size: 20X9.0
Offset: 0 (Chevy/GMC/Dodge)
Backspacing: 5.0" (Chevy/GMC/Dodge)
 

 

Or the Black Rhino Shrapnel

20x9.5

Offset 12

 

 

A 285/60 should fit just fine with either wheel size. A 285/60 is about a 33.5 x 11 and a 285/55 is 32.3 x 11. I would personally run the 285/60 as its only .5 inch taller than stock whereas the 285/55 is nearly an inch shorter. That 285/60 under load will probably sit at about 33 inches on the truck. The 285/55 under load will be less than 32 inches and look small on the truck/wheel plus will cause the speed to be off more.

  • Like 1
Posted
44 minutes ago, Smrtasp said:

A 285/60 should fit just fine with either wheel size. A 285/60 is about a 33.5 x 11 and a 285/55 is 32.3 x 11. I would personally run the 285/60 as its only .5 inch taller than stock whereas the 285/55 is nearly an inch shorter. That 285/60 under load will probably sit at about 33 inches on the truck. The 285/55 under load will be less than 32 inches and look small on the truck/wheel plus will cause the speed to be off more.

Thank you, very helpful. 

Posted (edited)

I posted pictures on an earlier date but I got new tires.  2019 RST, 2 inch level, with Black Rhino Apache 18x9 and Cooper AT3 XLT 285/65-18. 

Silverado Tires (2).jpg

Silverado 2 (2).jpg

Edited by Northwestern
Photo
Posted

Got tired of waiting for my lift.  Did some driveway fantasizing, emphasis on sizing.20200902_082759.thumb.jpg.8f459c143aed8f9adf7a8011b94e1c25.jpg

295/60/20 Vision Spyder 20x9 zero offset.    Funny there's no rubbing or trimming needed? ??

Posted

Just went through the whole thread and I think I know what will fit.  Just want to throw the question out to the experts on here.  I have a 2020 Trail Boss with mud flaps removed and Lund fender flares, they add about 3/4" to the fenders.  The stock 18's now sit back about 1 1/2" from the outside of the flares.  I want to run a 295/60/20 (34"x11.5") tire, I have the MotoFab 1" level but don't want to put it on unless I have to.  What offset on a 20x10 will fit without rubbing?  I'm thinking a 0 offset should push the outside out 1.5", am I right?

Posted
285/65 20 on stock rims no rub has about a 1/2 inch of clearance on inner wheel well


Sent from my iPhone using Tapatalk

Is this stock height? Sorry if I missed a previous post.


Sent from my iPhone using Tapatalk
Posted
On 8/24/2020 at 10:27 AM, Smrtasp said:

Went back and double checked the wheel and tire weights comparing the OEM 22s vs my new setup. Its actually a 19lb difference (Stock is 85lbs total and current setup is 104lbs) so quite a difference. If I change out to a 305/55/20 Nitto that will drop this to 89lbs so only a 4lb increase over stock but a 15lb difference with my current setup. I must have mixed up one of the tires when I was originally researching all of this as I was looking at a ton of different combinations. I also measured the current amount of space between the current 295/60 tire (runs at 33.9 x 11.77 width per Nitto) and my UCA and its right about 1.75 inches on each side and that was measuring off of the raised tread blocks. The 305/55 runs at 33.2 x 12.44 wide on a 9.5 inch wheel which I think will settle more into a 12.25 on a 9 inch wheel plus they are a bit shorter. Should be plenty of room and I have already done a bit of mud flap trimming to better accommodate the 34 inch tires on there now. Needless to say I went ahead and ordered the 305/55/20 Nittos today with the shop I use agreeing to buy my originals back at a decent price as they only have about 1,500 miles on them. I wont have time to get this done until the end of the week at the earliest but will report back once its done. 

Had the 305/55/20 ridge grapplers installed last week. Ride is a ton better than it was with the 295/60 E load rated ridge grapplers. The 305s are D load rated vs the OEM C load rated so they are still a bit stiffer than OEM but still the 305s are a 4 ply tire and softer overall. The visual difference on the truck is so small that I cant even tell the difference so didnt bother taking more pictures. I will say that even with some minor trimming of the mud flaps, the 295/60 had some minor rubbing at full lock. There is 0 rubbing now with the 305s. Even though the the 305s are 1 inch wider (11.5 vs. 12.5) on a 20x9 they are right about 12 wide. Im guessing that on a 20x10 they would be closer to the 12.5. With this change my speedo is also back to normal (was off by 2-3 mph depending upon speed) and I removed 60 lbs of rotating mass (15 per wheel/tire). This seems to be the sweet spot for my truck now so hopefully others with a Denali who are contemplating doing something like this will benefit from this info.

Posted (edited)

 35x12.50/17 BFG KO2 on a 17x8.5 DX4 Terrain 4.51 backspace -6 offset 

Icon 2.5 Extended Travel front coil overs at 2.25” lift 2.25” block in the rear with fabtech stealth shocks

Icons tubular UCA with delta join

Mudflap bracket removal 

Front fender liner plastic removed and zip tied away from the tire.

Lots of trimming on the mudflap and cut the bottom screw hole off the metal part of the fender. Bolted the mud flap back through the furthest hole for the bracket and gave me quite a bit of room with stock look.

Rides awesome and looks awesome!

5A3675F7-E293-4FDA-8145-D1C7473AC2B1.jpeg

80BD8EC9-F644-4BB6-84FB-D6E76C4629E4.jpeg

B69E8ECA-FA99-4138-875F-0129DAFD883C.jpeg

FBF548A4-0B43-4803-B5C3-D97C37AC9148.jpeg

Edited by Sierra50BMG
UCA
  • Like 1
Posted

Is this stock height? Sorry if I missed a previous post.


Sent from my iPhone using Tapatalk

Yes it is! Stock trail boss height


Sent from my iPhone using Tapatalk
Posted

I’m apologizing now....I’m sorry....there’s just so much information in this thread. [emoji1750][emoji1750]

 

2020 Sierra Elevation 2” level....what’s the biggest tire with zero trimming? Most likely Ridge Grapplers on 20 inch stock wheels, and/or 18 inch that I would potentially get. After looking through pictures, I like the look of more tire.

 

There are so many variations, Trail Boss, AT4, lifts, levels, stock, rim size...on and on haha.

 

Again, I’m sorry, haha, skip it if it irritates you, no hate needed.

 

 

Sent from my iPhone using Tapatalk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • First off, I'm not trying to just get easy advice/fixes for the issues I've noticed so far.  I'll be combing through the site via searches and such, and if past experiences are any indication, should find what I need.  For the sake of conversation, though, I figured I'd post the handful of things I've noticed in the 12 hours since buying my 2010 SLE CCSB.     Indicator lights: Airbag and TPMS.  The tire pressures aren't reading for any of the wheels, so I'm pretty certain the sensors were either removed, are damaged, or are otherwise inoperable.  I used to mount and balance tires 25 years ago but am pretty much ignorant when it comes to TPMS.  My 2006 didn't have the sensors and this might be the fourth vehicle I've owned that does.     Radio: Rear speakers aren't working.  I removed the driver's side rear door panel and checked the speaker and wiring.  I also removed the sill and b-pillar covers to check the wiring.  A few minutes of Google Fu showed that this is potentially a head unit issue.    Switches: Power mirrors don't turn left/right.  I ordered replacement driver's door switches that should arrive tomorrow.  The windows and locks work but it was only about $20 for all of them.  The driver's side rear window switch lets the window down but won't put it back up.  I think the passenger rear doesn't work at all.  In the coming days/weeks, I'll break out my multimeter to check all of that.   Unknown wiring harness: There's a box attached to the front driver's side of the engine compartment, right where the second battery shelf is located.  There are three plugs, one of which looks like it fits a standard headlight-style bulb (9007 or similar).  It doesn't look like it's plugged into anything.  I'll do some digging and if I don't see anything elsewhere on the site, post some pictures here.   Unknown plugs on brake booster: There are at least two female plugs on the brake booster that aren't being used.  I think it might be a replacement/aftermarket, so maybe those are used for a different application, as there don't seem to be any unplugged harnesses and no indicator lights are on.   Little squeaks when turning: Sounds almost like a bushing around the bed of the truck.  I'll have to pay close attention as I get more familiar with the truck.   Clunk on acceleration: possibly the infamous drivetrain clunk.  My 2006 had it and I'm just not familiar enough with this truck yet to fully grasp what it is.   Anyway, my apologies for the vague and all over the place post.  This truck is new to me, and it's been four years since I drove my 2006.  With 200k miles, I know I'll need to learn this truck quickly to avoid having any major issues, despite being confident it's got much more life to it.  My 2006 had nearly 320k on it when I parked it (nearly 300k of which I put on the truck), and it was still drivable then, though I suspected the head gasket might have blown.  I'd hoped to have that truck back by now, but it's gone forever, as I detailed in my reintroduction thread.  
    • I always drive in Sport mode. With more driving, I am finding the initial response when accelerating is much quicker now🖕 Lou
    • Is it an optical illusion in the pic or is the truck really squatting that much horribly?
    • My initial introduction was here.  It's hard to believe that I last posted in February 2013, having just deployed to Kyrgyzstan.  Since then, I've retired from the military and the 2006 Sierra SLT Z71 that first brought me to these pages was lost.  I went forward to Afghanistan in March 2013 and did a lot of sitting behind a computer on brigade staff.  Within 18 months of getting back to the States, I was selected for Drill Sergeant duty, after which I moved back to Virginia (my home state and where I served from 2004-2008).  That '06 Sierra did a lot of driving between Louisiana, Georgia, and Virginia, and ended up with nearly 320k miles by 2022.  By then, the registration had been expired for a couple of years, but the pandemic had all but eliminated tickets for such transgressions.  Admittedly too, I usually drove my wife's SUV or son's car the 2-3 times a week I had to report to work.  Teleworking sure was fun while it lasted.   I started my retirement leave four years ago and stored the Sierra at my sister's house.  A big mess was made when her fiancé passed while she was taking care of business out-of-state in late-2024, and his son pretty much mismanaged everything to do with the estate.  Even so, I was assured that my truck was safe... until it wasn't.  I found out that my truck had been scrapped about four months after the son took over everything.  There's nothing I could do; I'm 1000 miles away and it was technically abandoned property since he'd even trespassed my sister from her own house (she had no claim to it as she wasn't married, and the fiancé was the sole owner).     Anyway, today I got my second Sierra.  This is a 2010 SLE 2WB CCSB with a little over 200k miles on it.  It's got the 5.3L I'm familiar with and should handle what I need it for.  Hauling stuff that won't fit in the Transit Connect (yep, I sold out, but that's the wife's vehicle) and towing a few times a year tops.  The price seemed decent, considering how much people sell their trucks for in the Deep South: $4500.  I've seen similar trucks listed for more than double that.  I got it from a coworker who left his tag on until we transfer the title next week (Louisiana requires a notary for transfers), so I've been driving it all day.  The rear speakers don't work, which is one of the things that brought me back to these forums earlier.  I can't say how active I'll be as a poster, but I'll be scouring the archives while I find out every little thing I can about the 2010s and particular nuances/problems with my truck.   It's definitely not a GMC, but I got another Willys Jeep a few months back as well, so I'm almost at the same place I was when I first joined gm-trucks.com.  My old 1960 DJ3A was sold back around 2010 or 2011; my current Jeep is a 1946 CJ2A.  So, I've got a slightly newer GMC and a much older Jeep.  I kind of wish I still had that F-250 I had way back when too.  The Dakota is long gone and was technically my brother's truck, though I had it registered and insured.  The F-250 had to go when my grandmother's house was foreclosed on due to mismanagement around 2012 or so.     Hopefully anyone that made it this far isn't too annoyed.  I tend to be long-winded, but I'll be doing more reading than posting in the coming months.
    • There was a recall on the tailgate in general for opening on its own. Mine has a cap on it and it won’t let the tailgate open.   My tailgate has two holes in the top of the tailgate. I filled them in with silicone sealant. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...