Jump to content

Infotainment acknowledgements

sdelam

By sdelam
in 2020-2026 Silverado HD & Sierra HD

 Share

Recommended Posts

sdelam Enthusiast

sdelam

Posted
Posted

Anyone else get repeated notifications to acknowledge agreements? Doesnt happen everytime i start the truck but often enough to be annoying.

20190923_122729.jpg

J-man67 Senior Enthusiast

J-man67

Posted
Posted

They probably update it and need an approval for each edition.

Sent from my SM-N975U using Tapatalk

DougFL Enthusiast

DougFL

Posted
Posted

I only got the acknowledge agreements screen the 1st time I set up my profile on my 2019 Silverado 1500.  I have gotten 3 software updates since and no additional acknowledgment was required.

sdelam Enthusiast

sdelam

Posted
  • Author
Posted
43 minutes ago, MTU Alum said:

Does it come back after you accept the conditions during the next key cycle?

 

#iworkforGM 

Its intermittent, not every day/key cycle. Id guess every other day/4- 5 key cycles

MTU Alum Enthusiast

MTU Alum

Posted
Posted

I would recommend trying to see if your SD card is unlocked.  Power off vehicle, open and close drivers door, and let truck go to sleep (wait until green monster light is out).  Open center console, remove SD, look at SD card and there is a gray slider on left side of SD card, make sure that is in up position.  Reinstall SD and start the vehicle, accept all the messages and see if any return after a few key cycles.

 

#iworkforGM 

Shawn T Enthusiast

Shawn T

Posted
Posted

Mind of it's own, sometimes it's 5 or 6 starts in a row, sometimes it's good for 3 or 4. 

  • Like 1
Chrisw253 Enthusiast

Chrisw253

Posted
Posted

All the freaking time!  It seems to only happen when at home, and I do have it connected to my home WiFi. Wondering if it’s updates or what not but geez it’s annoying. I was coming here to post about it as well. 

4B575505-17CF-4415-A618-C6A04E4973E6.jpeg

Shawn T Enthusiast

Shawn T

Posted
Posted
34 minutes ago, Chrisw253 said:

All the freaking time!  It seems to only happen when at home, and I do have it connected to my home WiFi. Wondering if it’s updates or what not but geez it’s annoying. I was coming here to post about it as well. 

4B575505-17CF-4415-A618-C6A04E4973E6.jpeg

That makes total sense now that I think about it.  It only happens when I am close enough to my house to be connected to it's Wi-Fi

Coolade Enthusiast

Coolade

Posted
Posted
On 9/23/2019 at 3:00 PM, DougFL said:

I only got the acknowledge agreements screen the 1st time I set up my profile on my 2019 Silverado 1500.  I have gotten 3 software updates since and no additional acknowledgment was required.

3 updates, jeez that's a lot in the short amount of time being out.  Any thing new in the updates that you have noticed?

DougFL Enthusiast

DougFL

Posted
Posted
20 minutes ago, Coolade said:

3 updates, jeez that's a lot in the short amount of time being out.  Any thing new in the updates that you have noticed?

Truck is a year old.  Two major over the air updates to 803.1 and then 805.1.  One Messenger App re-download and 6 Dealer installed software (recall) updates.  Most appeared to be bug fixes like "Climate Off" and reduced volume issues.  Noticed some additional info to the HUD's navigation screen but other than that no obvious big change.

muddkatt Senior Enthusiast

muddkatt

Posted
Posted

That would drive me crazy.

Try blocking access on your router to see if it is indeed caused by hooking onto the Wi-Fi.

sdelam Enthusiast

sdelam

Posted
  • Author
Posted

 

 

7 hours ago, MTU Alum said:

I would recommend trying to see if your SD card is unlocked.  Power off vehicle, open and close drivers door, and let truck go to sleep (wait until green monster light is out).  Open center console, remove SD, look at SD card and there is a gray slider on left side of SD card, make sure that is in up position.  Reinstall SD and start the vehicle, accept all the messages and see if any return after a few key cycles.

 

#iworkforGM 

I beleive this is the correct position. 

20190924_160541.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • diyer2
      AFM Experience

      By diyer2 · Posted

      Hey guys, sorry for the confusison about this. This wasn't my experainnce, it was copied and pasted fom the net. 
    • KARNUT
      AFM Experience

      By KARNUT · Posted

      The problem with failure rates or increase failures are there’s people who don’t have a problem. What are you doing wrong they say. We had 4 5.7 GM diesel’s in the family when they came out. One was flawless. My uncle who happened to be the most abusive. Early rotary engines were known to use oil. I abused my first car so bad in six months I replaced the clutch, transmission and rear end. It didn’t use oil. My brother in law has a 2013 Tahoe and an older Yukon. The Yukon has 280K miles. The Tahoe around 175K. He runs them to about 300K. If his lifters fail before that time he would consider it a failure. My Hondas, I know people hate it when I mention them. Identical engines. One with cylinder deactivation one doesn’t have it. One shudders when the eco light goes on or off. Cylinder deactivation. But wait! According to the web. It can happen with lock up too. So now people in the know are changing the oil and transmission fluid more often. Then you read it could be a programing issue. So what do you do? There’s lots of money involved. I see three ways to deal with it. One only works if you don’t drive lots of miles. Lease, never get out of warranty. Or only buy older vehicles with a good track record. They all have bad runs. Usually when there’s a change. Even Toyota and Honda. 
    • Grumpy Bear
      AFM Experience

      By Grumpy Bear · Posted

      Question @diyer2 on this line if you please. Are you saying the shudder is the system turning on and off at the frequency of the shudder? Guess I'm asking if you are saying you have seen it do this with the bi-direction scan tool in graph mode? If so have you been able to discern the 'trigger'. Something is telling to cycle rapidly.    My truck just started doing this recently. 197K on the clock. My response has been M5 anything under 55 mph. I treat it like a lugging stick shift. Gear down and let it spin a bit. Engauge M5, then tow mode and then M6 lets the trans stay in 5th but the AFM is active. Smooth like Skippy.    My thought was that as a machine ages the friction gets lower and as the system is load based, the lower friction would allow it to turn on at ever lower rpm until it reaches the lugging point. And yes I am ignorant of any minimum rpm requirement for the system. If you know that would be useful information.    As you know I run a Scan-Gauge II which allows me to watch the On/Off of the signal to the VLOM. While in the shudder mode I'm not seeing is cycle at that frequency or at all for that matter outside the triggers @newdude posted a few years back. Now is it possible that the refresh rate isn't fast enough to catch it? Maybe. It is why I asked my first question about graphing and trigging parameter.     As we have observed from members here the failure point is all over the map miles wise as you note yourself in your opening post. That by itself begs a few questions like fellows that comment on these lifters failing even after the system has been disabled. Long after. 😬   https://www.enginelabs.com/news/tech-tips-replacing-ls-active-fuel-management-lifters-with-melling/   The Gen5 lifters operate the same as the LS versions. In fact they are the same lifter.    https://www.enginelabs.com/tech-stories/sorting-out-gen-v-lt-lifter-failure-with-a-simple-valvetrain-fix/        
    • SwitchBladeSierra
      14-18 Sierra 1500 Heated Steering Wheel Help

      By SwitchBladeSierra · Posted

      UPDATE 2: Steering wheel control backlights and control of the cluster can supposedly be achieved by adding a wire to pin 20 of the cluster and tapping it to pin 2 of the main clock spring harness. I'm going to give it a shot - will update  
    • newdude
      Seems to be Missing a lot of Updates

      By newdude · Posted

      GM Global A pickups 2019-2022 can do OTA programming for the radio.  GM VIP (GM Global B) can do OTAs for almost every module on board.  So a 2022.5 and newer pickup can do OTAs for recalls like the 2.7 fuel flow recall.  EVs get OTAs that improve one pedal driving, radio issues, HVAC issues, updated battery management software, etc.     So age of the vehicle/what GM electrical platform its on will alter what amount of updates can be pushed on OTAs.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...