Jump to content

Headlight adjustment 2020 GMC 2500hd AT4

Lance59
 Share

Recommended Posts

Lance59 New Member

Lance59

Posted
Posted

Have a 2020 GMC 2500 hd AT4 , and had it leveled, the headlight are now naturally aimed higher, and I’m getting flashed constantly.  Is there any adjustment to aim the headlights on this truck?  Also does anyone know if there is any aftermarket fog light bulbs or lights available to replace the stock ones that are worthless?

AE23887D-8474-4655-AEAB-537E210B62BD.jpeg

diyer2 Senior Enthusiast

diyer2

Posted
Posted

Ever heard of Google?

Here's one for ya. Found with Google.

 

:)

Lance59 New Member

Lance59

Posted
  • Author
Posted
4 hours ago, diyer2 said:

Ever heard of Google?

Here's one for ya. Found with Google.

 

:)

The headlights are completely different between the chev and the GMC...that was no help, but thanks 

  • Haha 1
diyer2 Senior Enthusiast

diyer2

Posted
Posted

Sorry!

You can't find this with a search?

 

:)

mkeddie Enthusiast

mkeddie

Posted
Posted

And that isn't for the 2020hd so less helpful then not posting....Google doesn't have all the answers



Picture is from owners manual
Not sure what the piece to the left of the bulb is but looks like a adjuster
Other then that I would take it to the dealer if there isn't a obvious adjustment screw95824eb2899734de9148998e1ee4ace6.jpg

Sent from my Moto Z (2) using Tapatalk

Lance59 New Member

Lance59

Posted
  • Author
Posted
3 hours ago, mkeddie said:

And that isn't for the 2020hd so less helpful then not posting....Google doesn't have all the answers



Picture is from owners manual
Not sure what the piece to the left of the bulb is but looks like a adjuster
Other then that I would take it to the dealer if there isn't a obvious adjustment screw95824eb2899734de9148998e1ee4ace6.jpg

Sent from my Moto Z (2) using Tapatalk
 

Thank you!

  • 4 months later...
Dunn Senior Enthusiast

Dunn

Posted
Posted

in manual it says to see a dealer but ill check to see if I can find same screw on 2020

  • 6 months later...
Dunn Senior Enthusiast

Dunn

Posted
Posted (edited)

couldnt find it on my Silverado......does anyone know?....

 

EDIT; pretty sure i found it on silverados, its bit tricky and way down as housing is much lower than years past.....

Edited by Dunn
Kkevin Enthusiast

Kkevin

Posted
Posted

If you look straight down behind the headlines the is a white nylon cone shaped piece. I can’t remember exactly what fitting it takes, (tore) but that adjusts your headlights up and down. Super easy to do. And for Diyer2, ever heard of the old saying if you don’t have anything good to say, don’t say anything at all?

  • Like 1
Dunn Senior Enthusiast

Dunn

Posted
Posted
On 1/12/2021 at 8:17 PM, Kkevin said:

If you look straight down behind the headlines the is a white nylon cone shaped piece. I can’t remember exactly what fitting it takes, (tore) but that adjusts your headlights up and down. Super easy to do. And for Diyer2, ever heard of the old saying if you don’t have anything good to say, don’t say anything at all?

exactly where the cones are.....can you just turn the cones?.....its along ways down there and normal screwdriver is not even close to long enough.....its tight area in there

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      So, do I go elbow-deep on this thing or list it for sale and play dumb? Seems to "runs good."   I'm about $1200 away from having: -a rebuilt injector ($300) -a new cat ($250) -a new cat back exhaust (OE style) ($300) -a new AC compressor ($200) -AC refrigerant charge ($150)   In theory, this should rectify the obvious detracting issues from its value and operability. Cold AC with a non-squeaking AC pulley both sounds and feels good. An exhaust that isn't cut/hacked in 17 different places and doesn't vibrate on a crossmember would make it sound and feel less janky. A working cat would help the stink, and will save the earth, but *if and only if* the fuel system is working properly, which would also address the intermittent "rich" CEL.   Heard a good one... CEL for "Rich condition" means you haven't spent enough money on the truck lately, and it's letting you know.   Rebuilding the injector would seem to be the most important part. Replacing the cat would be secondary. I don't think mine is plugged or overly restricted, but it might be a little restricted? I have no good way to tell other than seat of the pants feel. I hate the smell.   The current theory is I have a rich idle problem: A bad fuel pressure regulator, or a leaking injector(s) being the highest probabilities. I already replaced the FPR but that doesn't mean its replacement isn't also bad. It was a new part from Dorman, but the packaging looked like it had been sitting on a shelf for 20 years.   This is the (single) upstream O2 sensor shown at idle. I'm getting a lot of "rich" it seems. Sometimes it stays high like that and doesn't drop down. That makes me think it's processing injector leaks or a partially stuck open injector.     Other times it looks like this. Nice oscillations between rich and lean, which is what I think it should be. Under load and at speed, the oscillations are nice and tight and uniform looking, high and low.     Fuel trims suggest the PCM is compensating pretty hard at idle to pull fuel out. But it's not enough to trip a CEL. Something about slowing to a stop: brake vaccum booster, EGR, or the EVAP purge is delayed, or there's pooled fuel in the intake again that's draining into a cylinder is enough to set the CEL. Of course, in two days of driving, it hasn't set. I was hoping to actually look at the freeze-frame data when it sets. IAT is high because it's idling on an 83 degree day here.  
    • Another JR
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By Another JR · Posted

      Have considered installing a DC to DC charger in your camper to replace your isolator?  
    • newdude
      Gas fill door

      By newdude · Posted

      Common failure.  You need to replace the fuel door housing.   The painted cover transfers over to the new housing.  To remove the old one there is 4 spots where you poke the plastic to release it.  
    • newdude
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By newdude · Posted

      No such thing as regenerative braking on a pure ICE vehicle.     Regenerative braking is the re-capture of energy from electric motors and stores it in the battery pack.  So hybrids, PHEV and EVs have regenerative braking.     What you are seeing is the charging system changing modes is all.  Its likely entering charge mode for some sort of reason is all.  All of the charging modes will be listed below.   As for L10 vs D.  L10 turns off automatic grade braking.  L10 puts you in control of grade downshifts where in D it will automatically do it based on brake pedal position and other factors.  Otherwise L10 and D drive exactly the same aside from that one aspect.    Battery Sulfation Mode The BCM will enter this mode when the interpreted Generator output voltage is less than 13.2 V for 45 minutes. When this condition exists the BCM will enter Charge Mode for 2–3 minutes. The BCM will then determine which mode to enter depending on voltage requirements.   Charge Mode The BCM will enter Charge Mode when ever one of the following conditions are met:   Windshield wipers are ON for more than 3 s. Climate Control Voltage Boost Mode Request is true, as sensed by the HVAC control module via serial data. High speed cooling fan, rear defogger, and HVAC high speed blower operation can cause the BCM to enter the Charge Mode. The estimated battery temperature is less than 0°C (32°F). Battery State of Charge is less than 80%. Vehicle speed is greater than 145 km/h (90 mph) A current sensor malfunction exists. System voltage is determined to be below 12.56 V When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.   Fuel Economy Mode The BCM will enter Fuel Economy Mode when the estimated battery temperature is at least 0°C (32°F) but less than or equal to 80°C (176°F), the calculated battery current is less than 15 A and greater than −8 A, and the battery state-of-charge is greater than or equal to 80%. Its targeted generator output voltage is the open circuit voltage of the battery and can be between 12.5–13.1 V. When fuel economy mode is active, the generator is not charging, only maintaining open circuit battery voltage. The BCM will exit this mode and enter Charge Mode when any of the conditions described above are present.   Headlamp Mode The BCM will enter Headlamp Mode when ever the head lamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.   Start Up Mode When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 s.   Tow/Haul Mode (if applicable) Pressing the Tow/Haul Mode button located on the center stack, the vehicle system voltage is raised and the remote (non-vehicle) battery will be charged. Having the headlamps on will raise the system voltage and if the Tow/Haul button is applied it will not serve any purpose. The voltage is regulated between 13.9-14.5 V.      
    • jaszr2
      Active Grille Delete

      By jaszr2 · Posted

      Hello from Australia Just sharing that there is now a way to delete the active shutters entirely with just a plug in module. Opens up tons of room to light bars etc.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...