Jump to content

Recommended Posts

Posted

Reference Number: GCUS-9-11418

 

2021 Model Year Full Size Truck & SUV Feature Change

 

June 7, 2021

 

Chevrolet, GMC and Cadillac Dealers:

 

As promised, we want to continue to keep you in the loop regarding the global, industry-wide shortage of semiconductors.  Today, due to this shortage, we are announcing a new change to select full-size SUV and light duty full-size pickup truck powertrains.  The Automatic Stop/Start feature will no longer be available on certain 2021 model year:

 

  • Chevrolet Tahoe and Suburban
  • GMC Yukon and Yukon XL
  • Cadillac Escalade and Escalade ESV
  • Chevrolet Silverado 1500
  • GMC Sierra 1500

 

This affects only vehicles equipped with 5.3L (L84) and 6.2L (L87) V8 engines mated to 10-speed transmissions (MQB/MQC) starting with vehicles produced on or after June 7, 2021. By taking this measure, it will enable continued production and delivery of inventory to help respond to the strong customer and dealer demand for our full-size SUV and pick-ups as the industry continues to rebound and strengthen.

 

For orders with a scheduled production date on or after June 7, 2021, GM will build most full-size SUV and full-size pickup trucks equipped with a V8 engine and 10-speed automatic transmission with the added RPO code NSS- Not Equipped with Automatic Stop/Start (refer to the updated Order Guide and table below for trim details). This RPO code will be reflected on the Dealer Invoice along with an associated $50 MSRP credit.  The Monroney label will include this credit and indicate that the vehicle was built without Automatic Stop/Start.  These vehicles will also receive revised EPA certified fuel economy estimates.   Please note that any vehicle that has NSS is not equipped with Automatic Stop/Start technology, even if the vehicle also includes the KL9 RPO code (which was retained based on other components that remain on the vehicle). Chevrolet, GMC and Cadillac are updating all consumer and dealer facing materials as appropriate.

 

Any sold orders of these affected vehicles which have not been entered in the Production Order Management and Scheduling system by June 8, 2021, will be built without Automatic Stop/Start.  The dealer has the responsibility to and must advise affected sold order customers immediately. In addition, dealers are strongly urged to counsel directly with all customers who purchase affected vehicles to ensure each customer understands its vehicle content and efficiency.  This change to the availability of Automatic Stop/Start is currently expected to remain in place for the remainder of the 2021MY.  A listing of affected trims is listed below and is subject to change by General Motors:

  • Like 2
Posted

I will gladly donate the electronics to any Chevy dealer willing to take this horrible "feature" off my truck.

  • Like 4
Posted
3 hours ago, BossTaco2020 said:

I will gladly donate the electronics to any Chevy dealer willing to take this horrible "feature" off my truck.

Same!!!  LOL

  • Like 1
Posted (edited)

I'm very eager to see the revised MPG estimates without Auto Start/Stop (ASS). [Pun intended]

I have never thought ASS would improve mileage much, so I already wonder how much the EPA will influence what manufacturers are allowed to publish.

 

Edit: I'm definitely not a fan of ASS and turn it off every time I start my truck. And I'm considering the eliminator harness as well (reverses the default from on to off).

 

https://www.autostopeliminator.com/collections/gm/products/2019-silverado-sierra-autostop-eliminator 

Edited by Chevrolet1
  • Haha 1
Posted

Ass doesn't help the mileage but it "can" make for a fun ride

Posted

I don't even care how well it works. I'm not a fan. I'd gladly donate the related electronics for mine, as well.

 

Dangit...missed the cutoff for DFM delete and ASS delete. NOW they decide to make these trucks right....sheesh

Posted

So all jokes aside, what are the details on this?  Is this a chip that can just be removed or is there a new chip they're using that just doesn't have this feature?  I know I can get the eliminator, but if there's a factory method for just removing something that sounds safer and easier.

Posted
On 6/11/2021 at 10:46 AM, Chester Mooney said:

So all jokes aside, what are the details on this?  Is this a chip that can just be removed or is there a new chip they're using that just doesn't have this feature?  I know I can get the eliminator, but if there's a factory method for just removing something that sounds safer and easier.

Probably not as easy as you want it to be. If the chip or the module that controls ASS is not there they probably changed the program to not function. In other words GM probably turned that feature off in the program. Now if you were to do the same. Remove the chip/module yourself. I bet it would throw codes and your check engine light would come on. Because the program would trying to use that system but the controller you removed is not there. 

Posted (edited)

If this carries over into the 2022 model year I may look to trade my 2021 in just to get rid of S/S.   Since AutoStop is such as great feature I assume my truck will be worth a premium on trade.  LOL

Edited by elcamino

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • Anyone have any info about backorder time? It's classic 4th of July hot here in ohio.
    • There would be one way of determining the quality of the factory oil although probably more than a typical oil lab test, and that would be to draw out some oil from a new truck and send a sample to a lab that could do a more elaborate test of the oil. The issue with too little oil in the diff may not be the lack of lubrication of the diff bearings and gears themselves ( although a lack of oil volume for cooling ) but the wheel bearings because at some point the oil would be too low to properly get onto the spinning axle or fed along the axle tube. That was the claim by the local dealer from a couple of trucks in recent years that had the wheel bearings fail and they figured from lack of sufficient oil due to a severe underfilled diff and some of the bearing material made its way to the diff and it got damaged as well so the axle housings were just replaced on warranty. But your right that if the diff is over filled by whatever margin that it causes more churning of the oil than is desirable and that is no good either and can cause a pinion seal to leak. Also old oil I believe can tend to loose some of its properties like antifoaming and another good reason to change the diff oil every so often. 
    • I would be surprised if the diff's were not filled (with the cheapest gear lube) at the axle factory before being shipped to GM.  If you ever watched them building trucks they install the axles and all suspension parts with the frame upside down and then turn it over before its time to install the engine.     Too much gear lube in a axle can be worse than not enough especially with a lower quality GL where is get whipped up with entrained air (foam)  weakening its ability to lubricate.        
    • This is the 6.6 gasser section of the forum, you should either delete or modify your previous post as it is misleading for anyone looking for factual information on their 6.6 gas engine.
    • Well....I've done my first intake gasket. Probably wrong, but...we'll see?   Ultra black on the china walls and 1/4" up onto the sides of the intake gaskets. Permatex High Tack (couldn't find Gaskachinch) on the head side of the intake gasket. I read wrong and it says you're supposed to put it on the mating surface of the head, not the gasket. Hoping it's like a PB&J sandwich where it doesn't matter what side the PB goes on so long as there's jelly. That crap is messy/sticky and I got a dab or two on the intake port openings, tried to wipe it off. Hopefully it won't be a big deal and will only aid in sealing.   Per instructions I left the intake (top side) of the gasket dry except for a light smear of RTV around the coolant ports. Wiggling the intake in there was a bear but I had help to free me of surrounding wiring/stuff but I was basically able to set it straight down lined up with the bolt holes.   I did not think to wait until the RTV skinned over but there probably was 5-10 minutes while it sat before installing the intake.   Bolts finger tight first. Then, followed the Chilton's manual pattern to snug them to 15 lb-ft.   Waited a little over an hour, and then did the final torque in sequence again to 35 lb-ft.   Yesterday I replaced the fuel pressure regulator and got my new "nut and bolt kit" (fuel lines) installed. Damn GM used security torx on the spider, which I don't have, so I got scammed at the local HW store for an off-brand security Torx bit set.   The new driver's door mirror arrived yesterday, so, there's a chance this thing could be running and road legal tomorrow? I don't want to get my hopes up.   This will be my first time stabbing a distributor, too. Although, lucky me, someone else marked the old distributor for removal previously, I did see that. (Someone's been here before!!). Engine is still at TDC so it *should* be just a matter of transferring the mark to the new dizzy and rotating it into place.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...