Jump to content

Oil catch can?

C25A1guy

By C25A1guy
in Engines & Drivetrain

 Share

Recommended Posts

Smoore8691 Enthusiast

Smoore8691

Posted
Posted

Mine will also be here today! There are a lot of good install videos on youtube

Thanks, i seen this vid on youtube but was unsure if it would be the same since i have a Airaid MIT

  • Replies 1.9k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

ToesonTheNose
ToesonTheNose

Here at RX now they are doing a video install on my truck

Jay700
Jay700

My dealership said my catch can wasn't needed and wouldn't catch anything. I opened it in there shop after 2,000 miles and let it run on the floor. Lol

fondupot
fondupot

So, I added a second output fitting to my Original RX catch can. I had been emailing with the RevExtreme folks about the benefits of a dual output can, and they were gracious enough to send me the par

Posted Images

GDI Tech Enthusiast

GDI Tech

Posted
Posted

Should have all you need. You will be capping the passenger side of the air bridge like in this video:

 

 


Should have all you need. You will be capping the passenger side of the air bridge like in this video:

 

 

Smoore8691 Enthusiast

Smoore8691

Posted
Posted

Should have all you need. You will be capping the passenger side of the air bridge like in this video:

 

 

Thanx man!

acc412 Enthusiast

acc412

Posted
Posted

Thanks, i seen this vid on youtube but was unsure if it would be the same since i have a Airaid MIT

With the intake, this video helps.

acc412 Enthusiast

acc412

Posted
Posted

After getting my Elite and reviewing the system, i am unhappy with the hoses they have provided and the pain in the rear clamps they give (Be careful for the intake fitting as it is plastic). What should be the correct hose to use for this system?

duquephart Enthusiast

duquephart

Posted
Posted

After getting my Elite and reviewing the system, i am unhappy with the hoses they have provided and the pain in the rear clamps they give (Be careful for the intake fitting as it is plastic). What should be the correct hose to use for this system?

 

 

Substandard hoses do seem to be an issue.

Smoore8691 Enthusiast

Smoore8691

Posted
Posted

Got my dual exit can and clean side separator installed on my 6.2 today. Is it normal during wide open throttle my oil pressure shoots up to 70? Once you let off oil pressure goes back to normal 40

 

 

Sent from my iPhone using Tapatalk

acc412 Enthusiast

acc412

Posted
Posted

Yes I've had that happen to me on my 5.3. Have someone rev your engine while you look at the lines coming to your catch can

Smoore8691 Enthusiast

Smoore8691

Posted
Posted

Ok thanks. Yeh I've checked all my lines and everything looks to be hooked up correctly. It's running fine, just wide open throttle my oil pressure shoots all the way up.

 

 

Sent from my iPhone using Tapatalk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • PunchT37
      Scan Tool Recommendation

      By PunchT37 · Posted

      I just bought this. A minimum for me but, I don`t work anymore and don`t want the heavy update costs of the higher end tools. You would have to make money with them.   https://www.topdon.us/collections/diagnostic-tools/products/artidiag-pro   Even this tool has a $250.00 update cost after 2 years.
    • CamGTP
      Scan Tool Recommendation

      By CamGTP · Posted

      I have an Autel, works great for what it is. Can't do some specific things because you need say the GM tool, VCDS for Audi/Volkswagon and others of course. But those times are few and far between for me.   The other tool I'd like to try one day is the new Topdon scan tools. Seen several video's on them and many youtube people review them.    I've never subscribed for updates or payed to do that stuff on my Autel, so I'm sure I'm missing out on some of the updates but I'm fine with that for now.
    • Tyler Gibbs
      PF63 Oil Filters Going Away?

      By Tyler Gibbs · Posted

      Oh dear god why
    • AndrewF
      Scan Tool Recommendation

      By AndrewF · Posted

      I am in the market for a bidirectional scan tool so was hoping someone can help point me in the right direction. There are so many options out there it is hard to narrow down which make/model to choose.   I have always done my own vehicle work so looking to maximize capability with the scanner. Ideal price is $1k or less but would be willing to exceed if it opens up significant benefits.  Currently my 24 2500 is the newest vehicle but also have a few mid to late 2010s Subarus as well.    It seems that the Autel MP900 has a decent amount of features at a reasonable price?
    • C/K Man
      Silverado 4500-5500-6500 are they still being produced? Would have sold better as GMCs as well

      By C/K Man · Posted

      There was talk over the last couple of years that the contract to build these trucks between GM and International would not be renewed.  International moved production of all their other trucks besides the companion CV model out of the Springfield plant some time ago when they opened their San Antonio plant.  That left Springfield only building the Silverado Medium Duty, International CV Series, and some Express/Savanna long wheelbase cutaways.  International also put the plant up for sale some time ago.  This all answered my earlier question as to why GM and International did nothing with these trucks since they were introduced, as they had basically become a market 'placeholder' with a finite life.    The Silverado Medium Duty/International CV trucks were interesting combination of a GM powertrain, electrical system, and K2XX Silverado cab with an International chassis that was supposedly designed for a step-van type vehicle they never produced.  They were manufactured in International's Springfield plant along with the IH MV series initially.  When first introduced, there was much talk that the Silverado Medium Duty/CV would eventually get a gasoline engine option along with other upgrades and GM and IH would work on a class 6/7 joint venture truck.  This was before VW bought Navistar out, after that happened no more was said.  Draw your own conclusions...   About the time talk started that the GM/IH joint venture was not going to be renewed, rumors started that GM would develop a new line of medium duty trucks themselves.  The story is the new trucks will be part of the next generation HD's due in 2028, and will still feature a 'straight rail' chassis design that the current medium duty has.  GM views this as a desirable feature that differentiates their truck from the competition.  A gasoline engine option is also expected.  As the current Silverado Medium Duty remains in production until September 2026 and there is still a lot of inventory available do not expect any official word for some time.   I believe GM remains committed to their successful partnership with Isuzu, and all the LCF models will still be available from Chevy Commercial dealers.  Isuzu is on the cusp of opening a new large plant in South Carolina and there is also speculation that this may result in new product for both Isuzu and Chevy Commercial dealers.                  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...