Jump to content

What have you done to your K2 today?

block8head

By block8head
in Modifications & Accessories

 Share

Recommended Posts

LongrangeLauber Senior Enthusiast

LongrangeLauber

Posted
Posted

71708bee0f450537d98709ced4148eda.jpg

 

Anyone know what this top wire is for? The bottom two harnesses are for the light control and dim switch' the top wire was just seated in a blank clip on the back...

 

 

Sent from my iPhone using Tapatalk

Trailer brake control
  • Replies 23.1k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

RKeeper1
RKeeper1

Hauled this precious cargo home for the first time from the NICU after 40 days!   Sent from my SM-N900V using Tapatalk

Mileguru
Mileguru

I installed this thingy on the top of my 2017 6.2L. Not really sure what it does, but my truck goes really fast now.  

pgamboa
pgamboa

Found an hour of free time yesterday and installed GM - Illuminated Door Sills. Love the way they look! Of course, made a how to video. The box didn't come with instructions and tried searching he

Posted Images

Kerrslight Enthusiast

Kerrslight

Posted
Posted

Switched out my single row light bar for a curved double row. My measurements were off just a little bit so bar is a tad bit higher than I wanted it. At some point I'll redo it and slide it down just a tad and that should center it perfectly, just ran out of time yesterday. Anyways, this thing is crazy bright. Much better output than the single row. Exactly what I was looking for.

 

e9ed59f216214ae09db348683ead7680.jpg

6721046329a5dae2b9407af458423978.jpg

92bce13d357d4727e8a66f2945af80cb.jpg

a2ba2391105d6d86ed43bf88340f173e.jpg

f95f63d1533d35e5998f8783c6efb92a.jpg

7d2e0a74918d63a1b323322eb4169f16.jpg

LongrangeLauber Senior Enthusiast

LongrangeLauber

Posted
Posted

Ok thanks. And actually there's 3 total two of them are unused

 

 

Sent from my iPhone using Tapatalk

Also goes to 4wd shift knob
LongrangeLauber Senior Enthusiast

LongrangeLauber

Posted
Posted

Got home from my vacation. Between travel round trip and miles we put on while we were there, I put on about 1500 miles. This was from our trip back, 90% was through the mountains so I must say the fuel mileage is excellent

 

f63a699b45db9398818ccc64529e23ba.jpg

  • Like 1
block8head Enthusiast

block8head

Posted
  • Author
Posted

Second cup holder and new seats for the weekend project. :D

 

 

 

IMG_8910_zpsddneh4ig.jpg​

IMG_8911_zps4h8pqzmx.jpg​

​

LongrangeLauber Senior Enthusiast

LongrangeLauber

Posted
Posted

Second cup holder and new seats for the weekend project. :D

 

 

 

IMG_8910_zpsddneh4ig.jpg​

IMG_8911_zps4h8pqzmx.jpg​

​

Brown HC seats in a black interior? I wanna see how this comes out! Take pics!
block8head Enthusiast

block8head

Posted
  • Author
Posted

Brown HC seats in a black interior? I wanna see how this comes out! Take pics!

 

I have the complete interior including the dash/steering wheel and center console. not sure if I want to replace the dash or keep the black one. LOL

  • Like 1
kchiasson64 Enthusiast

kchiasson64

Posted
Posted

4c33f11a1a490ecf61e1f89a72a34476.jpg so far I have a blacked out go recon third tail light. Color matched bow ties. Rigid industries grill with rigid leds also I have the rigid fog bracket with rigid pods brightness is unreal. I also have the new platinum series scrubblade wipers with double edged scrub blades, I case you haven't yet you need a pair of these wiper blades. I have them morimoto 6000k hid kit in my projectors. Tactical seat covers. And a full Jo audio sound system. American force wheels and tires are on their way :)

 

 

Sent from my iPhone using Tapatalk

  • Like 1
kchiasson64 Enthusiast

kchiasson64

Posted
Posted

JL audio sounds incredible. I also plan on doing the center console swap. And adding the tow hooks with the lower valence. Add me on instagram kajun504

 

 

Sent from my iPhone using Tapatalk

LongrangeLauber Senior Enthusiast

LongrangeLauber

Posted
Posted

 

I have the complete interior including the dash/steering wheel and center console. not sure if I want to replace the dash or keep the black one. LOL

That's a lot of work. Good luck haha
  • Like 1
Dadof2 Enthusiast

Dadof2

Posted
Posted

I have the complete interior including the dash/steering wheel and center console. not sure if I want to replace the dash or keep the black one. LOL

 

I like brown interiors and have a HC. I often wish the dash was black though. I think it will look great.

Good luck.

  • Like 1
LongrangeLauber Senior Enthusiast

LongrangeLauber

Posted
Posted

I like brown interiors and have a HC. I often wish the dash was black though. I think it will look great.

Good luck.

I agree but I would like to see a truck with a black dash and brown HC seats. I'm not going through the trouble of swapping dashes though haha

 

Sometimes it reminds me of those 70s and 80s cars with brown dashboards lol

block8head Enthusiast

block8head

Posted
  • Author
Posted

I agree but I would like to see a truck with a black dash and brown HC seats. I'm not going through the trouble of swapping dashes though haha

 

Sometimes it reminds me of those 70s and 80s cars with brown dashboards lol

 

Looks like The black dash is staying. The HC dash is Damaged from transit :( They are offering partial refund for it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Texas Gasser
      Travel Trailer 2024 2500 HD 6.6 Gas Engine ?

      By Texas Gasser · Posted

      My truck is a 2024 2500 LT crew cab with the 6.6 gas engine and 10 speed trans.  It has a payload of 3578 lbs.  We pull a 22' Grand Design 17MKE that has dry weight of 5006 lbs. and a gross weight of 6395 lbs.  The trailer weighs about 5800 lbs. when loaded up with all the gear.  I don't fill the water tank for travel as most of our trips are to state parks that are within a day's drive.  Depending on the wind I get anywhere from 7.5 to 9 mpg.  I do use a weight distribution hitch (WDH) and have no problems with sway or being pulled/pushed side to side by 18-wheelers passing by me.  The trailer is about the same length of the truck so that helps a lot.  I say that because we traded in our 33' Grand Design 2670 MK (7800 lbs. loaded with gear) and using the same WDH, it would get pulled side to side by big trucks passing by me. It was not bad, but you needed to stay alert and know when a big truck was pulling up beside you.  I got about 7 to 8 mpg pulling that trailer.  I normally drive about 65 to 67 mph when pulling.  Overall, I love the payload capability of the truck as I doubt I will ever get close to its limit and I love the stability it offers over a half ton truck while pulling a trailer.  I have just over 30000 miles on the truck and have not had any issues.  We live in Texas where it is relatively flat, just windy. 
    • Chuck FB
      Gas Prices

      By Chuck FB · Posted

      I will say though that the 5.00 a gallon for only one fuel stop while on the Number 1, that privilege of driving from the point of Paso Robles ( where I fueled up before crossing to the coast ) and all the way up ... across the Golden Gate where I stopped and walked on the bridge ( and someone jumped off the bridge opposite the side I was on ... never saw it happen but the tow truck/paramedic told me ) and continued on north back onto No 1 and all the way up to where it connects to 101 and also explored some of the Red Woods although had been through some of that before. The fantastic view of that scenic ocean route was most certainly worth the extra dollars I spent on fuel. Just prior to that I had driven through Death Valley and that was some experience in the middle of July, then spent a couple of days in Yosemite and hiked to the top of Half Dome. The summer of 2007 was very memorable for what I saw and experienced in California.
    • AndrewF
      Travel Trailer 2024 2500 HD 6.6 Gas Engine ?

      By AndrewF · Posted

      Really depends on what extent the towing is.  Are you going across the country on highways or to fairly local campgrounds?  If you're just local towing then I wouldn't derate your truck much, just make sure the weight of your trailer and equipment stays below your limit.  Which for my truck is 14500lbs bumper pull.  Yeah it will work hard when you're over 5 figures in weight but who cares if it is just say 50 miles.    In my opinion the main thing with towing campers is wind resistance.  My 3200lb single axle camper tows fairly hard for what it is due to the wind.  But then if I use my truck to tow a family members 8000lb camper it doesn't really feel any different as wind resistance is similar. I've also towed a 5000lb airstream and it barely felt like anything was there.
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      I think the excitement has run its course. Or, probably need a break from the truck for a few days.   Win some, lose some, again. There was still a coolant weep from the front of the engine. This time it was one of those worm-drive hose clamps on the upper hose connecting to the water neck. There's a reason the factory doesn't use those type of clamps; they suck. The hose is all distorted and flared at the end from someone over-tightening it. The water neck just needed to be cleaned, hose seated, and have a *good* hose clamp put on, if the hose wasn't so mangled.   Thought I'd kill two birds with one stone and try to diagnose the EGR issue. It's likely a failed EGR but before I spent $85 on the part I wanted to make sure ports weren't clogged or the pintle wasn't stuck. It was kind of a bugger to remove with the upper intake installed. Re-install (because I wanted to drive it) proved more difficult.   Per the stack of service paperwork, the EGR has already been replaced 4 times since 1996.   It would reason, then, that the EGR flange on the lower intake manifold has had its share of techs trying to work quickly and maybe one of them seated a bolt slightly cross-threaded at one time. The bolt didn't come out without significant effort and tried as I did, it wouldn't go in without significant effort. And then, the mounting ear on the right side of the EGR (lower intake casting) cracked, and crumbled off. $%&@!!!   I hate everything. Or, at least, I did in that moment. I was pretty calm, considering. This is what older, junky vehicles do. They nickel and dime their owners, piss them off, and things break that shouldn't break because of shoddy design/workmanship, poorly done repairs.   If I want to make it right, I'll need to replace the lower intake manifold and basically re-do everything I spent days doing. At least it should go quicker this time, right?! Looks like a lower intake (used/junk, of course) will run me about $150.   Once I get the new EGR, I'll see if I can bolt it up snug enough to verify proper operation, and if it solves the persistent CEL that sets on decel for EGR flow, I'll know I'm back on the right track. And then I can decide how to proceed.   Also, an idler pulley has given up. It began squeaking in pain on startup. It's clear this truck hasn't been thoroughly driven in a long, long time as things are just letting go and shaking out. I may have given it the beans once or twice to make sure my intake gaskets were doing their job. Flog an old vehicle, expect what it gives in return.    
    • GMC4Zee
      Trailer TPS Sensor Question Rim Size

      By GMC4Zee · Posted

      Thanks for the info but wow, these are pricey! $100 apiece. A full set of smaller ones can be had for less that the cost of one of these. Gotta be a cheaper option out there but I have yet to find it. I don't want to use grommets as I can see leaking in my future. Now that I am looking at it, I might be able to just get the valve stem and modify the sensor to fit. Looks like I can just modify the hole a bit to adapt.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...