Holy squeaks!

By Dale Mitchell
January 16, 2019 in Troubleshooting & Recalls

Recommended Posts

Dale Mitchell

Posted January 16, 2019

I changed the brakes and rotors out on my 14 Silverado crew cab about a month ago go to the brakes squeaking non stop, and a visible gouge on the driver side rotor. The pads still had about 60% on them but changed them out anyway, here I am a month later and the same damn squeaking is back, there is no visible sign of anything dragging the rotor but holy hell is it annoying. Anyone had this issue?

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

Similar Content
- Grinding noise ONLY in reverse gear.
  
  By Nathan Sauserman, September 6, 2024
  - Silverado
  - grinding
  - (and 1 more)
    
    Tagged with:
    
    Silverado
    
    grinding
    
    brakes
  - 4 replies
  - 6,416 views
- brakes Brake Fluid and testing for brake fluid SAVANT LABS
  
  By customboss, July 29, 2024
  - brake fluid
  - fluid
  - (and 6 more)
    
    Tagged with:
    
    brake fluid
    
    fluid
    
    testing
    
    brake system
    
    brake upgrades
    
    insurance
    
    accident testing
    
    service brakes
  - 0 replies
  - 962 views
- 2020 Sierra Rear Brakes Issue, Inside Pad Bad Outside Still Good
  
  By alvarezz09, June 21, 2024
  - brakes
  - pads
  - 4 replies
  - 4,607 views
- Soft brake pedal 04 silverado
  
  By Silveradoz7104, June 5, 2024
  - Brakes
  - 9 replies
  - 6,026 views
- Brake System Failure, Service ESC, Trailer Brakes Disabled
  
  By PeoplesAlpha, February 14, 2024
  - denali ultimate
  - bds suspension
  - (and 3 more)
    
    Tagged with:
    
    denali ultimate
    
    bds suspension
    
    brakes
    
    buy back
    
    lift kit
  - 3 replies
  - 8,025 views
Recently Browsing 0 members
- No registered users viewing this page.
Forum Statistics

250.3k
Total Topics

2.7m
Total Posts
Member Statistics

342,688
Total Members

8,960
Most Online

Newest Member
NN16HD
Joined 4 hours ago
Who's Online 1 Member, 0 Anonymous, 470 Guests (See full list)
- Shall36

Latest Articles
- GM Recalls 2,700+ Trucks For Airbags That Can Explode While Parked – How To Check Your VIN
  Wednesday at 07:54 PM
- You Can Completely Disable A New Chevy Traverse By Bending The Rear Wiper Arm (No, Seriously)
  Wednesday at 05:47 PM
- Should You Use Engine Fuel Additives In Chevy or GMC? Here’s GM’s Official Statement.
  Wednesday at 02:38 PM
- We’ve Driven the Edition 1 For 4 Years. Here’s Why the Mid-Size HUMMER X Concept is Exactly What GMC Needs.
  May 29
Posts
- ATTENTION anyone with oil pressure issues
  
  By davester · Posted 1 hour ago
  
  The filter under the OPS is for engines with AFM, which didn't start for trucks until 07.5 I think around '02/'03, when GM rejigged the computers and wiring, they also moved to a multi-pin OPS, but still didn't have the filter under it.
- Avalanche
  
  By davester · Posted 1 hour ago
  
  Because everyone hates them. They have all the downsides of a truck, combined with the downsides of a 'burb, and then add in a hole in the roof.
- 2016 2500hd Steering Issues
  
  By davester · Posted 1 hour ago
  
  maybe post a pic showing the results of the alignment, someone might see why?
- 2016 2500hd Steering Issues
  
  By NN16HD · Posted 4 hours ago
  
  Hi everyone, looking for some input on an issue I’m having with my truck. It’s a 2016 2500HD Crew Cab LT with the 6.0. A couple of months ago I had the pitman/idler arm and tie-rods replaced at a shop with some good quality parts and then professionally aligned after that. Immediately I noticed that the steering is much tighter/heavier feeling and has zero play of any kind. However the steering will not “return to center” at highway speeds now, for example if I’m going around a slight curve with the wheel turned and I let go of the wheel the truck will continue to turn instead of the wheel re-centering like it used to. It makes it so I’m constantly fighting to keep the truck going straight down the center of the road. I should also note the truck does have the “NV8” electronic steering assist. I’m wondering if I need to have the steering control module re-programmed? Or is it an alignment issue? All of the alignment parameters were in spec from the shop. Maybe someone else has had this issue, I appreciate any feedback, thanks!
- Avalanche
  
  By dna9656 · Posted 4 hours ago
  
  How come there's no Avalanche Forum?
GM-Trucks.com Clubs
- Black Truck Club
  
  Open Club · 612 members
- White Truck Club
  
  Open Club · 380 members
- Canadian Owners Club
  
  Open Club · 282 members
- Red Truck Club
  
  Open Club · 156 members
- diesel 3.0
  
  Open Club · 279 members
- Texas Owner's Group
  
  Open Club · 371 members
- NorthSky Blue Club
  
  Open Club · 118 members
- Midwest Owner's Group
  
  Open Club · 212 members
- 2015 Custom Sport Club
  
  Open Club · 5 members
- GM Snow Plowing Club HD
  
  Closed Club · 14 members
Popular Contributors
- Week
- Month
- Year
- All Time
1. 1
  
  KARNUT
  22
2. 2
  
  Atlas
  18
3. 3
  
  Grumpy Bear
  9
4. 4
  
  diyer2
  9
5. 5
  
  mdipasquale20
  6
Show More

Sign In

Holy squeaks!

Recommended Posts

Dale Mitchell

Archived

Similar Content

Grinding noise ONLY in reverse gear.

brakes Brake Fluid and testing for brake fluid SAVANT LABS

2020 Sierra Rear Brakes Issue, Inside Pad Bad Outside Still Good

Soft brake pedal 04 silverado

Brake System Failure, Service ESC, Trailer Brakes Disabled

Recently Browsing 0 members

Forum Statistics

Member Statistics

Who's Online 1 Member, 0 Anonymous, 470 Guests (See full list)

Latest Articles

Posts

GM-Trucks.com Clubs

Black Truck Club

White Truck Club

Canadian Owners Club

Red Truck Club

diesel 3.0

Texas Owner's Group

NorthSky Blue Club

Midwest Owner's Group

2015 Custom Sport Club

GM Snow Plowing Club HD

Popular Contributors

Activity

Tools

More