Jump to content

Roof Leak from Shark Fin (Digital Radio Antenna)

hamooz
 Share

Recommended Posts

SS502 Senior Enthusiast

SS502

Posted
Posted
3 hours ago, silverado2k18 said:

my 2018 has the gap towards the back, with wifi.  my buddy's 2018 has the gap towards the front, with wifi.   same year.......

Of course! Sorry, MOST of the newer trucks have it in the front. It's not a water seal but for some reason GM started putting the gap towards the front. I plan on putting a sealant around the base of mine, hopefully it will stop water from getting to the seal inside that is SUPPOSED to keep the water out.

  • Replies 30
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

dsr611
dsr611

Just a few of the many topics on the roof leaking around the antenna... https://www.gm-trucks.com/forums/topic/217719-shark-fin-antenna-swap-observstions-and-why-they-leak/ https://www.gm-tr

imiller1974
imiller1974

The dealer "replaced/fixed" it under warranty. It leaked again within a month of them working on it...So, I fixed it myself for the price of a tube of RTV/silicone.   Remove the A pillar tri

Donstar
Donstar

My antenna leaked and was repaired while under warranty.  It leaked again, post warranty, and my dealer replaced it at no charge.  They service manager said the new one is a better design and I should

Posted Images

RACERX7775 Enthusiast

RACERX7775

Posted
Posted

I guess GM designed the seal and said, we know this is gonna fail so lets design it so when water gets it, it can get out too? WTF? Id like to know the real reason why its designed like it is..

2003 SSEi Enthusiast

2003 SSEi

Posted
Posted

The Rubber with the gap, is not a seal.  It is simply a way to attach the antenna to the roof, and have a good contour and not have any paint wear or direct contact from the plastic of the antenna to the roof. 

 

As pointed out, you should not silicon the OUTER section of the antenna, as the gap is designed to let water/air out.  The correct way is to remove the antenna, and use a silicon/RTV/whatever you want in addition to the foam seal.

 

here are some pics from my thread

 

I never had a leak in 90K miles as you can obviously see here.  You can see the outer rubber of the antenna, and then the inner seal area.

09D2B601-D49A-4829-AFCB-391968D5E488.jpeg

 

 

This is the Foam seal that actually does all the work to keep the water out

22A6FA13-2622-4C09-AD2B-F0AD56A16F27.jpeg

 

The only reason I swapped was to go from the 14 Non painted Antenna on my Denali to the 15+ Painted antenna

g2full Enthusiast

g2full

Posted
Posted

Has anyone tried using stip caulk/dum dum/whatever everyone calls it? I think that's what I'm gonna try on mine when I take it off to "improve".

 

 

  • 3 weeks later...
hamooz Enthusiast

hamooz

Posted
  • Author
Posted

Thank you y'all of your help.

 

My technician friend came last week and resealed the thing. We had to remove the headliner to have an access to the antenna. 

 

I used "GE All Purpose Silicone - Clear" to reseal the stupid fin.

 

I hope the leak will stop permanently. However, I did lose my signal for the XM radio. It says "Receiption may be blocked".

 

My just re-activated the membership and tried to refresh the signal multiple times, but still no signal.

 

I'm not sure what is really the cause of the connection issue. We made sure every wire were properly re-connected. I suspect the antenna has been defective after the leaking occurred. 

 

Shame on you GM! trying to save some money to build and install cheap parts leading to major issues. :fume:

IMG_20190223_204100.jpg

hamooz Enthusiast

hamooz

Posted
  • Author
Posted
23 hours ago, RACERX7775 said:

Did it say it was blocked before you removed the antenna?

No, XM radio was working before I removed it.

RACERX7775 Enthusiast

RACERX7775

Posted
Posted

Well, either you blobbed to much on or you damaged the connector.  Its gotta come apart again to see what happened. You didnt take the antenna apart did you? Its just the one bolt right? This is on my 14, i think the newer ones are a tad different because of the wifi..

20180911_163627.jpg

hamooz Enthusiast

hamooz

Posted
  • Author
Posted
On 2/26/2019 at 9:36 AM, RACERX7775 said:

Well, either you blobbed to much on or you damaged the connector.  Its gotta come apart again to see what happened. You didnt take the antenna apart did you? Its just the one bolt right? This is on my 14, i think the newer ones are a tad different because of the wifi..

20180911_163627.jpg

That's what I think too. I might blobbed too much but I don't think I damaged the connector.  

II just loosened the bolt that holds the antenna, I did not fully remove it.

 

I will just by another antenna and I hope that will fix the problem.

  • 3 weeks later...
hamooz Enthusiast

hamooz

Posted
  • Author
Posted (edited)
On 3/1/2019 at 11:57 AM, RACERX7775 said:

Why buy a new one. Take it off, peel the stuff off, reapply just enough to seal it.

We worked on it last weekend. We checked the wiring and try to remove the excessive rtv.

 

However, after several attempts, it still says "signal may be blocked" . I refreshed the signal multiple times through the XM website, but the antenna did not pick up any signal.

 

I ended up putting a new antenna. As soon as I connected it, "signal may be blocked" was disappeared . I finally got my XM radio working back after refreshing the signal with the new fin.

 

It costs me overall over $100 to fix the stupid leak and to restore the signal:

$10 for the clear RTV and the Caulking Gun

$50 for the new antenna (part # 23258394)

$50 for the labor cost that I paid for my technician friend

 

If I were going to the dealer to handle it, they would charge me nearly $300 to reseal it.

Edited by hamooz
  • 2 months later...
Ridgerunner30 Enthusiast

Ridgerunner30

Posted
Posted

So it started raining inside the truck on Sunday.  2015 Silverado.  I removed the shark fin antenna.  Cleaned up the sealing surfaces and applied pure silicone sealant.  We'll see how long this works.  A hole in the roof is not a very bright idea.  

  • 5 years later...
HotRodDan New Member

HotRodDan

Posted
Posted

I have the same issue with my 2018 Equinox. Spare tire tub fills up with water when it rains hard. I've been wondering if my sunroof had been leaking cuz I had water in the back seat floor area as well. Could be more extensive than originally anticipated.

Not sure the reason or cause but I've noticed this came all of a sudden after I've been running my car through the automatic car wash. It's the one with the rotating flapping pads or strips. And those flaps beat on the sunroof and shark fin antenna. I may think twice about that particular type of brushless car wash once I finally get my leaking roof fixed.

swathdiver Senior Enthusiast

swathdiver

Posted
Posted
4 hours ago, HotRodDan said:

I have the same issue with my 2018 Equinox. Spare tire tub fills up with water when it rains hard. I've been wondering if my sunroof had been leaking cuz I had water in the back seat floor area as well. Could be more extensive than originally anticipated.

Not sure the reason or cause but I've noticed this came all of a sudden after I've been running my car through the automatic car wash. It's the one with the rotating flapping pads or strips. And those flaps beat on the sunroof and shark fin antenna. I may think twice about that particular type of brushless car wash once I finally get my leaking roof fixed.

Put some clear RTV around the antenna and that should stop the leak.  Continued use of those car washes will tear the RTV off.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      Oil Consumption

      By Chuck FB · Posted

      Through the years it hasn't been my typical method as I tried to drop oil on an engine that was hot from having been worked, however that was not always practical and had to fire up a unit and let it warm up reasonably well and drop the oil when I had the time to do it but am referring to not only vehicles but a variety of farm equipment and highway tractors etc. However on a vehicle where one is crawling under it and the exhaust is nearby to ones body and if wanting to pull the plug without danger of being hit with boiling hot oil or attempting to remove a HOT oil filter, its sure safer and easier to not have everything smoking hot and can remove the filter right away when under the vehicle and let it all drain. Of course its not the end of the world if a bit of oil stays in the engine that might have eventually found its way out, I like to get out as much as possible but any oil changes that take place in shops would rarely be sitting around for very long at all before the plug is thrown back in and filter slapped on and oil poured in and sent out the door quick like. There would be very little time spent ( assuming they even did it ) in starting the engine with oil to fill the filter, then waiting to verify the level on the stick. A good reason to check ones oil level shortly after a shop changed the oil on a vehicle just to make sure its correct and to look under for any oil around the drain plug or filter. 
    • CPhelps
      4 Wheel Drive System

      By CPhelps · Posted

      Cool to see another Vermonter!
    • diyer2
      Winter Returned

      By diyer2 · Posted

      To many wildfires.
    • diyer2
      Oil Consumption

      By diyer2 · Posted

      I have changed oil and filter for years by starting a cold engine to warm oil up, let it run 5-10 minutes depending on temperature. Drain until it starts dripping, refill with quantity from owners manual or get it close.   
    • Chuck FB
      Fluid Change Questions

      By Chuck FB · Posted

      I changed the factory fill oil in the rear diff of my truck for the first time today and the miles is close to 9000 on the truck. There was a lot of fines on the magnet, a very thick layer but working it through my fingers it all felt like mush and as most know it appears like graphite, so no surprise chunks anyway. Certainly was time to do it from my thinking and could have been done sooner but the oil didn't look awful but sure wasn't new looking and never expected it to either. I did use some solvent to help me clean out the bottom area of the axle housing, just get any other stuff settled at the bottom washed and wiped out of the housing for the bit of effort it takes. I used Amsoil Severe Gear 75W90 in the easy packs to try out what they are like and I used up 4 packs and didn't spill much at all in the process but did take all four of the packs and go to the work bench and emptied them into a measuring container and there certainly was some in them that added up to something, then poured that into one of the easy packs and squirted in what I could get out of it. I would say the level is within 1/8th of an inch of being level with the threads at the fill plug so just the perfect amount. Once again, more than what GM says the fill volume is but computes with what others are adding to their rear diffs as well. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...