Jump to content

Tailgate LED Bar

Trailboss75
 Share

Recommended Posts

BlackLS Enthusiast

BlackLS

Posted
Posted
22 minutes ago, Opiedeegs said:


Did you remove your entire tailgate for the installation
I have a GMC multi pro the wiring harness to unplug is not the simplest


Sent from my iPad using Tapatalk

No, I had just enough room to squeeze my fingers between the bumper and tailgate to install the light bar.

  • Like 1
  • Replies 72
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

BlackLS
BlackLS

I have the Putco Blade and used the Putco "Plug and Play" harness which connects to the trucks tail light wiring harness not the trailer lights.   I tried the Curt harness from Amazon but my

NHAT4
NHAT4

I did,  but I only wanted a solid red led ( I don't care for the turn flashers, back up etc of them) ... so I  hard wired the running light / stop light wires of the led strip into the taillights.  I

PhilB
PhilB

I think you have to use the module to deactivate the tow package.  You would still plug it in to the CURT adapter.  Using the CURT adapter is the way to go to avoid hard-wiring the LED strip.  On my '

Posted Images

Opiedeegs Enthusiast

Opiedeegs

Posted
Posted
No, I had just enough room to squeeze my fingers between the bumper and tailgate to install the light bar.

My fingers are too short and fat


Sent from my iPad using Tapatalk
Opiedeegs Enthusiast

Opiedeegs

Posted
Posted

I had quite a bit of difficulty trying to remove the multi pro tailgate
Could not get the passenger side hinge to release
I got the blade installed anyways would’ve been much easier without the tailgate
The wiring harness is nice so you don’t have to scotch lock any of the tail light wires


Sent from my iPad using Tapatalk

Nola Sciko Enthusiast

Nola Sciko

Posted
Posted (edited)

I have the Opt 7 with module on my Rst. Works and looks awesome only down fall is that u loose the rear bumper sensor function.  I could not figure out how to hardwire/tap in to the taillights 

Edited by Nola Sciko
Jacob007 Enthusiast

Jacob007

Posted
Posted
3 hours ago, Nola Sciko said:

I have the Opt 7 with module on my Rst. Works and looks awesome only down fall is that u loose the rear bumper sensor function.  I could not figure out how to hardwire/tap in to the taillights 

All other adapters will throw errors on your dash and think

you have a trailer connect when the truck is in motion. Below is the only adapter you can use with no trailer errors and backup sensors work. Trust... learn from my mistake

https://www.putco.com/529005

 

 

 

 

 

C62CB48F-1DD5-4698-A791-E41C91FF8302.jpeg

  • Like 1
Nola Sciko Enthusiast

Nola Sciko

Posted
Posted
46 minutes ago, Jacob007 said:

All other adapters will throw errors on your dash and think

you have a trailer connect when the truck is in motion. Below is the only adapter you can use with no trailer errors and backup sensors work. Trust... learn from my mistake

https://www.putco.com/529005

 

 

 

 

 

C62CB48F-1DD5-4698-A791-E41C91FF8302.jpeg

Will that adapter work with the Opt?

Trailboss75 Enthusiast

Trailboss75

Posted
  • Author
Posted
6 hours ago, Nola Sciko said:

I have the Opt 7 with module on my Rst. Works and looks awesome only down fall is that u loose the rear bumper sensor function.  I could not figure out how to hardwire/tap in to the taillights 

I think you need this module for the Opt7 lights.

 

http://www.opt-7.com/tow-package-module-for-redline-led-tailgate-bars/?sku=820-02427&gclid=EAIaIQobChMInZOOurTt4wIVCZ6fCh1iJAafEAQYASABEgKd9vD_BwE

 

 

Opiedeegs Enthusiast

Opiedeegs

Posted
Posted
All other adapters will throw errors on your dash and think
you have a trailer connect when the truck is in motion. Below is the only adapter you can use with no trailer errors and backup sensors work. Trust... learn from my mistake
https://www.putco.com/529005
 
 
   
 
C62CB48F-1DD5-4698-A791-E41C91FF8302.thumb.jpeg.6d8368221d7ea77891b48d426226197e.jpeg

Second that Putco is clean and simple
No wire taps


Sent from my iPad using Tapatalk
Blanco1500 Enthusiast

Blanco1500

Posted
Posted
On 8/5/2019 at 5:49 PM, Nola Sciko said:

I have the Opt 7 with module on my Rst. Works and looks awesome only down fall is that u loose the rear bumper sensor function.  I could not figure out how to hardwire/tap in to the taillights 

I sent in a question to the Tech Support guys at Opt7. Here is their response:

 

Thank you for your inquiry.
Unfortunately, we were not able to receive a screenshot from your previous message.
The module is a universal application, it will work with most vehicles.

The Triple Tailgate has 3 possible installation methods: Plug & Play; No module. Plug & Play with module and hard-wired.

Triple Tailgate Only (Plug & Play): Vehicles that do not have any of the following equipped:
-Rear Camera
-Back-up/Parking Sensor
-Trailer Assist Feature (HUD display that provides trailer connection status notifications)
-BLIS (Blind Spot Notification Signal)

Triple Tailgate + Module (PWM Adapter) (Plug & Play): Vehicles equipped with any of the following:
-Rear Camera
-Back-up/Parking Sensor
-Trailer Assist Feature (HUD display that provides trailer connection status notifications)

Triple Tailgate (Hard-wired)
-BLIS (Blind Spot Notification Signal)
-Some tailgates will only function hard-wired on certain vehicles.

* Vehicles with a BLIS or Blind Spot Sensor Systems must use the hard-wire extension kit included with the kit. 
The kit will technically not be Plug & Play in this case.

**Vehicles that do not have a BLIS or Blind Spot Sensor System but do have a rear camera, rear parking sensor or a Trailer Assist System that provides heads up display status updates will require the addition of the OPT7 Optional Accessories Signal Module.

Best Regards,
Salvador G. 
OPT7 Customer Experience Team

  • 5 months later...
Rich Kesteloot Enthusiast

Rich Kesteloot

Posted
Posted

I purchased this with the add on module for my 2019 GMC Sierra Denali 1500.  I tried the curt adapter and I tried hardwiring as Opt 7 shows in a youtube video.  Both of these installs disabled my sensors and cross traffic alert thinking I was towing something.  Does anyone have a good remedy to solve this.  I contacted Opt7 and they said just send the product back for a full refund but I really like the look of the lights but losing all safety features is a real bummer.  Anyone have success with this?  Or suggestions. 

Rich Kesteloot Enthusiast

Rich Kesteloot

Posted
Posted
On 8/6/2019 at 8:31 PM, Opiedeegs said:

How do you install it with this harness?
Second that Putco is clean and simple
No wire taps


Sent from my iPad using Tapatalk

 

Ezekiel2517 Enthusiast

Ezekiel2517

Posted
Posted

I have a max trailer package on mine.  It has no 4 pin jack at all.  The absurdity of that aside, would the putco one still work in my case?

J2Jones Enthusiast

J2Jones

Posted
Posted
On 8/4/2019 at 7:42 AM, Opiedeegs said:

I had quite a bit of difficulty trying to remove the multi pro tailgate
Could not get the passenger side hinge to release
I got the blade installed anyways would’ve been much easier without the tailgate
The wiring harness is nice so you don’t have to scotch lock any of the tail light wires


Sent from my iPad using Tapatalk

 

I can get my passenger side off easily at 45 degree angle.  Can’t get the drivers side to release in any position.  How do you get the drivers side off?  Please help!

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • UrbanRage
      What have you done to your K2 today?

      By UrbanRage · Posted

      I have the same running boards on my truck and I do agree they are bulky. I also find myself stepping over them when getting in and out of the truck. Besides providing protection to the rocker panels, they aren't very useful.  I will be replacing them soon with the Amp Powersteps. 
    • ChristopherDobson
      Vehicle Payments

      By ChristopherDobson · Posted

      Monthly payment is only part of the equation. With today's prices and interest rates, I'd look at the total monthly cost: payment, insurance, registration, fuel, maintenance, and expected repairs. A vehicle that fits comfortably into your budget is usually the better choice than stretching for a higher trim. I've also kept my vehicles longer over the past few years. New cars have gotten expensive enough that driving one for 10+ years, while staying on top of maintenance, often ends up being the most cost-effective approach.
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      10 Ford and Chevy engines proven to reach 300,000 miles   You may note a common 3K OCI on this list of gas motors. I skipped over the diesels. Dh'O. 
    • jake111
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By jake111 · Posted

      Thanks newdude!  By the time manual selection is needed, I'm probably too much of a control-freak to depend on the transmission sensing braking to activate automatic downshifting.  I would be anticipating the situation and already be manually downshifting.   This truck replaced a 2004.5 LLY diesel with the Allison 5-speed.  Putting it in T/H made noticeable differences (when the torque converter locked, upshift points, downshift behavior).  On this 2024 gasser with the 10L1000 I haven't been able to detect much, if any, difference.  Ok, I can never tell now when the torque converter locks up.  But I also don't notice differences in shifting.  For downhills, I've probably already manually downshifted by then anyway.  Since it's also more awkward (than the 2004.5) to engage/disengage I don't even bother.  Or maybe it doesn't really matter with just a 3k lb. camper in the bed?   Thanks also for the list of reasons the charging system might select various voltages.  However, what I am seeing doesn't fall into any of those categories.  It very definitely, and very consistently, rises after coasting/braking.  Maybe not immediately, but not very long after coasting/braking.  Very consistently drops voltage when no longer coasting/braking.  It might also be interacting with the camper battery charging (I might disconnect the camper and see if it changes the charging behavior).  I also need to recheck turning on headlights for when I want to force it to charge the camper.   Another JR, in June I converted the camper to LiFePO4.  Since it's not a good idea to try to charge lithiums directly using truck, I installed a Victron Orion XS DC-DC charger (which BTW is AMAZING!!).  Being cheap, I only had to buy that one item (besides the battery, of course) to do the conversion.  The camper OEM 120v battery charger (only 19 years old and works perfectly) and the truck feed the input to the DC-DC charger (not at the same time).  But I didn't want the camper charger feeding back to the truck so I kept the old separator.  I considered replacing the separator with a 30amp diode but that means more work and might add another 1/2 volt drop.  One thing that surprised me was the voltage drop over the long 10awg wire run, so I can only charge smoothly at 8 amps (because the DC-DC charger is completely configurable).  Another reason I don't want an added voltage drop with the diode.  I might also be a little lazy but all this work is being done under the sink with a small cabinet opening.    
    • davester
      cam upgrade in CA

      By davester · Posted

      apparently CA smog is (or at least was)  checking that the vehicle is using the oem and/or a ca smog approved tune, so I expect you'll fail inspection doing it.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...