Jump to content

Frame plugs

DanTN

By DanTN
in Modifications, Wheels & Tires

 Share

Recommended Posts

kodiakdenali Enthusiast

kodiakdenali

Posted
Posted
On 7/20/2022 at 12:52 PM, Brent D said:

I dont want to steal kodiaks credit for coming up with the idea....but i just got a 3d printer and want to tinker and will try and post a .stl for these when i get a design that works well. Dont want to recreate the wheel but too cheap to pay for what i can maybe make.

**Please buy sets from Kodiak as I will not be making any to sell just for my own personal use. ** 

Kodiak...On a side note though maybe you could get a few $$ for .stl file alone privately for those who have printers but dont want to take the time to design.

 

I'll even give you a hand if you need it. What software do you like to use for 3d models?

the critical dimensions that worked for me, the ones for the part that gives a good tight fit on the inside of the square cross member are: width 68mm, height 71mm, corner radius 20mm. on my plugs actually the corners are the primary area of contact (where the fit is the most interference), this keeps them nice and tight but helps to make sure they are removable for periodic cleaning throughout the life of the truck. After all there are other passages for stuff to get inside the frame other than the open ends of the cross members. When capped it should reduce the introduction of debris and salt a huge amount. It's still good to be able to occasionally flush them out just in case.

  • Replies 75
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

kodiakdenali
kodiakdenali

Here you go:     I didn't check the whole frame, is it just this one square member? 2 outlets total? I need to make some for the round ones also.

kodiakdenali
kodiakdenali

It's been a lot of fun designing and using the 3D Printer for projects on my truck. If any of you are interested in some of my other adventures I also enjoy producing videos of the projects on my DIY/

Transient
Transient

Subscribed Just found out about something I didn't know I needed Sent from my SM-N960U using Tapatalk

Posted Images

Brent D Enthusiast

Brent D

Posted
Posted

I just started using tinkercad as it seemed to have the easist  entry into 3d world. I just got done making the round caps that worked for my application (2nd one still printing as we speak). I was getting a variable from the actual tinker cad to the end product of +/- .8mm which you wouldnt think is much but it is when it comes to sizing a hole that 1 isnt truly round, and 2 has some slight surface rust causing imperfections. I took me 3 itterations to come up with it a model that is tight and tough/flexible enough to  be pounded in with a mallet without cracking. Im using PLA+ though for now which is fine as it is not a moving part. Will upgrade to ABS down the road. I used digital calipers to know my large and small diameters and split the difference. My first one was just slightly too large and wouldnt even start to go in, the next one was too loose. This last one was tight but got it to go in . I used 1.73 diameter (didnt have calipers til today for mm) as a reference outter diameter for the plug and that seemed to work just perfect. I will start messing with the rectangles tomorrow.  I will post up the tinker cad files and .stl files for our users to mess with on here. I had fun just messing with it and the DIY. Just wish it didnt take 1.5 hours (twice) to find out it didnt work..lol

Brent D Enthusiast

Brent D

Posted
Posted

.obj file to adjust to whatever micro adjustments you need for your application. I ran mine at 100% infill .3mm height for speed using PLA+. Tool 1.5 hours each.

2019+GMC Caps Round.obj

Brent D Enthusiast

Brent D

Posted
Posted

Kodiak what 3d modeler are you using, cant seem to do radius with tinker cad as it wants to radius every side of object not just what I want. 

kodiakdenali Enthusiast

kodiakdenali

Posted
Posted
10 minutes ago, Brent D said:

Kodiak what 3d modeler are you using, cant seem to do radius with tinker cad as it wants to radius every side of object not just what I want. 

I use openscad for almost everything. I'm a programmer so the code based modelling is intuitive. Unfortunately I have no experience with tinkercad, heard of it, never used it.

I also do some work in freecad. The radius isn't the easiest thing in open scad either but with the right libraries its easy enough to produce. its pretty simple in Freecad though.

Brent D Enthusiast

Brent D

Posted
Posted

I have a lot of experience in Autocad, but all 2d...so its like starting over...will check out freecad.

kodiakdenali Enthusiast

kodiakdenali

Posted
Posted
6 minutes ago, Brent D said:

I have a lot of experience in Autocad, but all 2d...so its like starting over...will check out freecad.

I hear ya. You might find Freecad reasonable to learn then. its interface and UI and all are not quite like autocad but you make your 3d designs in one of a few different ways. you can insert primitives and do booleans on them, or you can draw 2D schematics then extrude them into 3D space. then you can pick a face on any surface in that mesh and create a new 2D sketch on that face and extrude or pocket to add geometry or make holes. And you can easily fillet or chamfer edges by selecting a 3D object, a face, or specific edges. 2D cad experience might translate fairly well.

  • 4 weeks later...
alvarezz09 Enthusiast

alvarezz09

Posted
Posted
On 5/26/2022 at 2:57 PM, kodiakdenali said:

Updated design for additional strength to make sure its removable for maintenance.

 

1373577636_Revision2.thumb.jpg.bfe24483398378c886fca9adb5a22d40.jpg

Do you have the object file by chance i really would like to print this! Thank you

  • 4 months later...
  • 1 year later...
Bucketmouth Enthusiast

Bucketmouth

Posted
Posted

If anyone is making them for a 2023 or knows where to get a set Im a buyer. It looks like the rear hole is about 1.75" and the rear opening is more squared and measures roughly 2.5x3" Does this sound correct?  Again, if anyone knows where I can get a set, Im a buyer maybe two sets.  Thank you.

Bucketmouth Enthusiast

Bucketmouth

Posted
Posted

One other thing. Has anyone thought of making a groove around the plugs for an o-ring or are they already plenty tight?  Thanks

kodiakdenali Enthusiast

kodiakdenali

Posted
Posted
35 minutes ago, Bucketmouth said:

One other thing. Has anyone thought of making a groove around the plugs for an o-ring or are they already plenty tight?  Thanks

I still make and sell them, shoot me a message! They do have a space on the back where a gasket or o ring would fit if you could locate one of the right size. I make both the square or round plugs.

  • Like 1
  • 4 weeks later...
  • 1 month later...
kodiakdenali Enthusiast

kodiakdenali

Posted
Posted
20 hours ago, BBL_28 said:

How do I contact Kodiakdenali directly to get a set of plugs?

 

Got your message! Contacting me though direct message right here is a good way to get a hold of me. I’m still making the plugs for anyone who asks for them. shipping costs a couple bucks more than it used to but I still honor the original price in this thread. Anyone looking for them, feel free to message me!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • diyer2
      AFM Experience

      By diyer2 · Posted

      Hey guys, sorry for the confusison about this. This wasn't my experainnce, it was copied and pasted fom the net. 
    • KARNUT
      AFM Experience

      By KARNUT · Posted

      The problem with failure rates or increase failures are there’s people who don’t have a problem. What are you doing wrong they say. We had 4 5.7 GM diesel’s in the family when they came out. One was flawless. My uncle who happened to be the most abusive. Early rotary engines were known to use oil. I abused my first car so bad in six months I replaced the clutch, transmission and rear end. It didn’t use oil. My brother in law has a 2013 Tahoe and an older Yukon. The Yukon has 280K miles. The Tahoe around 175K. He runs them to about 300K. If his lifters fail before that time he would consider it a failure. My Hondas, I know people hate it when I mention them. Identical engines. One with cylinder deactivation one doesn’t have it. One shudders when the eco light goes on or off. Cylinder deactivation. But wait! According to the web. It can happen with lock up too. So now people in the know are changing the oil and transmission fluid more often. Then you read it could be a programing issue. So what do you do? There’s lots of money involved. I see three ways to deal with it. One only works if you don’t drive lots of miles. Lease, never get out of warranty. Or only buy older vehicles with a good track record. They all have bad runs. Usually when there’s a change. Even Toyota and Honda. 
    • Grumpy Bear
      AFM Experience

      By Grumpy Bear · Posted

      Question @diyer2 on this line if you please. Are you saying the shudder is the system turning on and off at the frequency of the shudder? Guess I'm asking if you are saying you have seen it do this with the bi-direction scan tool in graph mode? If so have you been able to discern the 'trigger'. Something is telling to cycle rapidly.    My truck just started doing this recently. 197K on the clock. My response has been M5 anything under 55 mph. I treat it like a lugging stick shift. Gear down and let it spin a bit. Engauge M5, then tow mode and then M6 lets the trans stay in 5th but the AFM is active. Smooth like Skippy.    My thought was that as a machine ages the friction gets lower and as the system is load based, the lower friction would allow it to turn on at ever lower rpm until it reaches the lugging point. And yes I am ignorant of any minimum rpm requirement for the system. If you know that would be useful information.    As you know I run a Scan-Gauge II which allows me to watch the On/Off of the signal to the VLOM. While in the shudder mode I'm not seeing is cycle at that frequency or at all for that matter outside the triggers @newdude posted a few years back. Now is it possible that the refresh rate isn't fast enough to catch it? Maybe. It is why I asked my first question about graphing and trigging parameter.     As we have observed from members here the failure point is all over the map miles wise as you note yourself in your opening post. That by itself begs a few questions like fellows that comment on these lifters failing even after the system has been disabled. Long after. 😬   https://www.enginelabs.com/news/tech-tips-replacing-ls-active-fuel-management-lifters-with-melling/   The Gen5 lifters operate the same as the LS versions. In fact they are the same lifter.    https://www.enginelabs.com/tech-stories/sorting-out-gen-v-lt-lifter-failure-with-a-simple-valvetrain-fix/        
    • SwitchBladeSierra
      14-18 Sierra 1500 Heated Steering Wheel Help

      By SwitchBladeSierra · Posted

      UPDATE 2: Steering wheel control backlights and control of the cluster can supposedly be achieved by adding a wire to pin 20 of the cluster and tapping it to pin 2 of the main clock spring harness. I'm going to give it a shot - will update  
    • newdude
      Seems to be Missing a lot of Updates

      By newdude · Posted

      GM Global A pickups 2019-2022 can do OTA programming for the radio.  GM VIP (GM Global B) can do OTAs for almost every module on board.  So a 2022.5 and newer pickup can do OTAs for recalls like the 2.7 fuel flow recall.  EVs get OTAs that improve one pedal driving, radio issues, HVAC issues, updated battery management software, etc.     So age of the vehicle/what GM electrical platform its on will alter what amount of updates can be pushed on OTAs.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...