Jump to content

Recommended Posts

Posted (edited)
5 hours ago, Booger T said:

I've never had a problem with my dealer changing the settings on the tpms.

My dealer changed mine for me too.

After the change, the phone app shows the new programmed number as 'recommended'. 

 

(When loaded and running higher pressures, I don't get the monitor reprogrammed)

 

FWIW, the 2500's are typically 70 rear, instead of the 80 rear that is typcal on the 3500's.

Edited by redwngr
  • Like 2
Posted

My Goodyears(?) and 20" wheels on my 3500 AT4 seem to lose a pound or two a week. Going to have to take it back at some point for that and a couple other very little things.

Posted
My Goodyears(?) and 20" wheels on my 3500 AT4 seem to lose a pound or two a week. Going to have to take it back at some point for that and a couple other very little things.

All of them!? Or just one tire?
Posted

Yep, all of them. Hard for me to believe too.

 

It came delivered with the LR down to 76 psi. I pumped it up to 81. A week later the fronts were down in the low 50s and rears were both down to 76.

 

It's much colder out today than it's been, they're at 55 front and 73/75 rear. I checked them on the dash after pumping them up and they were 61/81 before we left for AZ two weeks ago.

Posted
2 hours ago, blamkin86 said:

Yep, all of them. Hard for me to believe too.

 

It came delivered with the LR down to 76 psi. I pumped it up to 81. A week later the fronts were down in the low 50s and rears were both down to 76.

 

It's much colder out today than it's been, they're at 55 front and 73/75 rear. I checked them on the dash after pumping them up and they were 61/81 before we left for AZ two weeks ago.

 

My January OnStar email shows that my tires went down from 60 psi in September when I bought the truck, down to 48 psi in both front tires. And the rears went down from 70 to 58 left and 60 right.

 

Sounds like it is just temperature related in the loss of psi.

Posted

I'll see if they come up next week. They did not go down when I was in the snow in Arizona last week. 

 

It does not seem like a temp issue to me, but I'm hoping you're right.

Posted (edited)
6 hours ago, SkidooSteve12 said:

 

My January OnStar email shows that my tires went down from 60 psi in September when I bought the truck, down to 48 psi in both front tires. And the rears went down from 70 to 58 left and 60 right.

 

Sounds like it is just temperature related in the loss of psi.

Don't forget the sun.  The left side of my truck gets more sun in the driveway.  So "cold" pressure on the driver's side is always higher after sunup then the passenger side.  Once on the highway and heated up, the tires are all the same.  Well, that is unless of course one side see more sun for a prolonged period of time!  LTs are more finicky than P-Metrics when it comes to air.  

 

I had to adjust the air more frequently when I ran them at or near rated capacity.  Now that we dropped them a few pounds, they stay at the set pressure much longer, months longer even.

Edited by swathdiver
Posted

My dealer reprogrammed the TPMS on my last two trucks, but refused to do it on this one. So, I run 50-55 psi all around for a while, and ignore the warning light. Eventually, I get tired of the light, and bump the rears up to 62-65ish just to make the TPMS happy. When I get tired of the firm ride, I drop back down to the 50's and start the process all over again, haha. 

  • Like 1
Posted
Factory set 60 front 80 rear
 
No plans to change, rides just fine.

I put my rears at 65 and it made a difference. Even at full capacity 80 isn’t needed. But if it’s comfy to you then nothing to worry about.

I’ll bump mine up when I start towing consistently. But even at 65 I have more than enough and it makes it a little less rough in the rear.
Posted
On 3/21/2020 at 8:22 PM, Big Whiskey said:

My dealer reprogrammed the TPMS on my last two trucks, but refused to do it on this one. So, I run 50-55 psi all around for a while, and ignore the warning light. Eventually, I get tired of the light, and bump the rears up to 62-65ish just to make the TPMS happy. When I get tired of the firm ride, I drop back down to the 50's and start the process all over again, haha. 

For about a $100 you can do it yourself and have full, dealer level diagnostics and testing at your fingertips.  VXDIAG NANO with GDS2 software.

  • 1 month later...
Posted (edited)

2500 was 70rr and 60frt.....I dropped to 55 on all 4 corners and no alerts or warnings....it does help some though but still could be better....since I don't need payload rating all the time ill just throw 500lbs in back and yank it when I need ability.....

Edited by Dunn
  • Like 1
Posted
My dealer reprogrammed the TPMS on my last two trucks, but refused to do it on this one. So, I run 50-55 psi all around for a while, and ignore the warning light. Eventually, I get tired of the light, and bump the rears up to 62-65ish just to make the TPMS happy. When I get tired of the firm ride, I drop back down to the 50's and start the process all over again, haha. 
I would drop by Discount tire, they are usually awesome about stuff like this, and they want your future tire business, so most of the small stuff they do free of charge.

Sent from my SM-G988U1 using Tapatalk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Common failure.  You need to replace the fuel door housing.   The painted cover transfers over to the new housing.  To remove the old one there is 4 spots where you poke the plastic to release it.  
    • No such thing as regenerative braking on a pure ICE vehicle.     Regenerative braking is the re-capture of energy from electric motors and stores it in the battery pack.  So hybrids, PHEV and EVs have regenerative braking.     What you are seeing is the charging system changing modes is all.  Its likely entering charge mode for some sort of reason is all.  All of the charging modes will be listed below.   As for L10 vs D.  L10 turns off automatic grade braking.  L10 puts you in control of grade downshifts where in D it will automatically do it based on brake pedal position and other factors.  Otherwise L10 and D drive exactly the same aside from that one aspect.    Battery Sulfation Mode The BCM will enter this mode when the interpreted Generator output voltage is less than 13.2 V for 45 minutes. When this condition exists the BCM will enter Charge Mode for 2–3 minutes. The BCM will then determine which mode to enter depending on voltage requirements.   Charge Mode The BCM will enter Charge Mode when ever one of the following conditions are met:   Windshield wipers are ON for more than 3 s. Climate Control Voltage Boost Mode Request is true, as sensed by the HVAC control module via serial data. High speed cooling fan, rear defogger, and HVAC high speed blower operation can cause the BCM to enter the Charge Mode. The estimated battery temperature is less than 0°C (32°F). Battery State of Charge is less than 80%. Vehicle speed is greater than 145 km/h (90 mph) A current sensor malfunction exists. System voltage is determined to be below 12.56 V When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.   Fuel Economy Mode The BCM will enter Fuel Economy Mode when the estimated battery temperature is at least 0°C (32°F) but less than or equal to 80°C (176°F), the calculated battery current is less than 15 A and greater than −8 A, and the battery state-of-charge is greater than or equal to 80%. Its targeted generator output voltage is the open circuit voltage of the battery and can be between 12.5–13.1 V. When fuel economy mode is active, the generator is not charging, only maintaining open circuit battery voltage. The BCM will exit this mode and enter Charge Mode when any of the conditions described above are present.   Headlamp Mode The BCM will enter Headlamp Mode when ever the head lamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.   Start Up Mode When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 s.   Tow/Haul Mode (if applicable) Pressing the Tow/Haul Mode button located on the center stack, the vehicle system voltage is raised and the remote (non-vehicle) battery will be charged. Having the headlamps on will raise the system voltage and if the Tow/Haul button is applied it will not serve any purpose. The voltage is regulated between 13.9-14.5 V.      
    • Hello from Australia Just sharing that there is now a way to delete the active shutters entirely with just a plug in module. Opens up tons of room to light bars etc.
    • I have an observation and a question... 1) I watch the voltage closely because I have had to dial in the cut-in/cut-out voltages of the battery separator to my camper.  The "smart" charging drives me nuts.  Anyway, I noticed that when coasting for a while, and especially if lightly using the brakes (though not necessary), the voltage goes up from mid/high-13 volts to mid/high-14 volts.  Then it drops back down after stopping or going again.  Consistently!   The only explanation I can come up with is REGENERATIVE BRAKING!  Well, maybe that's a little bit of an exaggeration, but it's certainly free extra battery charging.   2) Driving on mountain roads I will use L and vary the max gear.  Things straighten out and I end up in L10.  Sometimes I leave it there for a while.  Is there any difference between L10 and D?   
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...