Jump to content

Recommended Posts

Posted

Truck is a 19 Silverado 6.2L 10-Speed 4wd.

 

Took it into a dealer for my 45k maintenance, cause quite frankly, its too cold outside.  Already done everything but the transmission fluid/filter change.  Need to drop the exhaust just to drop the pan; PITA.

Dealer said I don't need to do the filter, and just needed to do the fluid.  The proceeded to quote me $639 at a $185/hr rate.  2.5 hours to just drain and refill sounds like a rip off, but I digress.

My issue isn't with the price, its with them stating I don't need to do the filter, when the manufacturer says to do it at 45k.  Any suggestions?  I already did the transfer case, and they said that was not needed until 60k.

Obviously I walked out and decided I will be doing it myself.  But do I need to do the filter or not?

 

Posted
10 minutes ago, clowe1243 said:

Truck is a 19 Silverado 6.2L 10-Speed 4wd.

 

Took it into a dealer for my 45k maintenance, cause quite frankly, its too cold outside.  Already done everything but the transmission fluid/filter change.  Need to drop the exhaust just to drop the pan; PITA.

Dealer said I don't need to do the filter, and just needed to do the fluid.  The proceeded to quote me $639 at a $185/hr rate.  2.5 hours to just drain and refill sounds like a rip off, but I digress.

My issue isn't with the price, its with them stating I don't need to do the filter, when the manufacturer says to do it at 45k.  Any suggestions?  I already did the transfer case, and they said that was not needed until 60k.

Obviously I walked out and decided I will be doing it myself.  But do I need to do the filter or not?

 

Always advocate dropping the pan to check for any foreign objects and to service the filter.  If the fluid looks normal on the dipstick then simply dumping the pan is good enough.

  • Like 1
Posted

Up to you. 

I would do it because the break in of the trans causes wear particles. 

Case in point, our Hyundai has a magnet on the trans drain plug. I did a drain and fill at 30k, magnet had quite a lot of stuff on it.

I did another drain and fill at 31k miles, magnet was clean. 

 

Posted

Like always I relate my experiences nothing else. Honda Odyssey 156k one complete drain and fill. Had a partial at the dealership one drop and fill at 100K miles. The complete by me at 127K. It took 3 drain and fills over several days. 4Qts at a time. Hyundai Genesis 142K. One at 60K, one at 130K. Drain and fill. Avalanche 2002 Z66. Only 1 at 156K by me. Pulled fluid through the dipstick over 3 days 3 times. The only time I ever changed a transmission filter was on my 1970  Grand Prix and my 1974 Nova. I was putting in a B&M shift kit. So naturally I changed the filter. I always believe and maybe times have changed. If the transmission filter is clogged, the transmission is toast.

Posted
1 hour ago, calgator73 said:

Always advocate dropping the pan to check for any foreign objects and to service the filter.  If the fluid looks normal on the dipstick then simply dumping the pan is good enough.

The 10 speed doesn't have a dipstick.

Posted

I would wait until it warms up and do it yourself. I would be willing to bet if you pull the transmission mount screws you can jack the tailshaft up high enough to get the pan clear. Install a drain plug or a pan with a drain plug, do your filter this time for reasons covered by @calgator73 and then at 90k just do a spill and fill. https://transpartswarehouse.com/k032-transmission-drain-plug-kit-made-in-the-u-s-a-universal-ford-gm-superior.html?network=g&device=c&keyword=&campaign=1656107452&adgroup=pla-297808671781&gad_source=1&gclid=Cj0KCQiApNW6BhD5ARIsACmEbkXSMFXz4i4Sb9Mil9fCtGsomKx26XuBUXBDq_bemKxF0q3PDIipzNkaAk76EALw_wcB

  • Like 1
Posted

This is a hot topic with the transmission folks.  I have never liked transmission flushes and have always dropped the pan and replaced the filter.  Many shops have been caught charging the people for a trans flush and doing nothing.  My faith in all dealers is gone.  In our owners manual, it says 45K for sever duty.  I plan to change my 2020 at around 50K or so but will not sweat pushing it up a bit.  Unless you were hauling the max towing, I would recommend not changing it at the 45K miles.  There are way too many horror stories of trans flushes causing all kind of issues with these 10 speed transmissions.  I already bought the filter, gasket and oil but like you, I am waiting for warmer weather to do it.  I removed the crushed cross over exhaust pipe and had a muffler shop weld in a true round pipe when it was new but did not plan ahead.  Now I am looking to design cross over pipe with flanges at the cats to make removing the pan a whole lot easier.  Getting up to the manifold nuts and removing the oxygen sensors is not a really fun job.

Posted

You don't have to drop the exhaust, a prybar and patience will do.  Many Youtube Videos

  • Like 1
Posted

For refilling the trans you can buy a hose nipple that threads into the fill hole on the side of the trans. I dont know the size on the other trucks but the 10spd on the 2500/3500's is M18. They are available on Amazon with a nipple for 1/2" hose. I attach the hose to it and run the hose up to where the dipstick should be. This way you can gravity fill the easy way. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • The timing marks are ok, that is #1, you can turn it over until they line up and it won't change anything, the crankshaft turns twice for every camshaft revolution, I have always set up SB Chevs as your pic shows using a straight edge
    • Someone's been here before.... There is a receipt for a 3-piece timing set, purchased earlier this year.   Is this picture something, or, nothing?   I have the timing cover off and my crank is perfectly TDC and the keyed gear's locating mark is dead on 12 o'clock.   The cam gear locating mark is also at 12 o'clock. Now, I'm not an expert, but all the install guides say the two locating marks should meet and be perfectly aligned when installing a timing set. The mark on the crank should be dead on 12:00 and the cam gear's mark should be dead on 6:00, and both marks should be perfectly vertically aligned.   I believe the timing gear is keyed or has a dowel that ensures it can only be installed on the cam in one position, so I have to believe the cam is out of phase somehow. At the very least, with a triangular bolt pattern, it can only be installed in one of 3 different positions.   Before I pulled the front cover, the truck was running alright, no service engine soon lights except an occasional P0172 / rich condition. Timing -16 timing at idle (should be +16), and total -35% fuel trim, two conditions I haven't been able to figure out.   In related news, my injector tested pretty well, wasn't leaking, but I had it rebuilt anyway, and it's on it's way back to me.         Along with this discovery, the good and bad:   Good: The oil pan seal appears undamaged.   Bad: -The timing cover has been reused, and the positioning dowels have been broken. That could explain some of the leaking. -Some kind of white paste or grease was used to try to seal the oil pan seal and timing cover (since wiped off..). -Then, someone globbed silicone all over the front of the cover and also buried the ckp sensor in it. But, they didn't put any inside the cover or use RTV to try to seal the oil pan seal with the timing cover (good).
    • The guy that owns K&P filters last I checked in with him has over 300,000 miles on his Dodge base Hemi using his own 35 micron absolute stainless mesh filter from its first oil change.    The GM study I've posted a dozen times shows the relationship in engine life based in multiples of base units, not miles or years. That is the base unit is the number of miles the motor ran using the reference filter efficiency.    The above two paragraphs dismantle anecdotal arguments IF one changes oil often enough to prevent particle formation and the motor is in otherwise good shape. That is not full of silica (no air filter) or suffering a metallurgical issue that is not part of the lubrication discussion. Poor heat treat in example.   Data from UOA's I've reviewed from more than a few engines can show remarkably broad variations in oil cleanliness using the exact same filter over the course of an engines life.     Lastly there is the common sense of it. Wear debris WILL circulate the engine BEFORE it ever sees a filter in route to that filter and WILL harm the pump which NEVER sees filtered oil.    Alpha question then becomes, given the facts, how long do you believe is a reasonable service life from a vehicle you are certain you will not pass down? That is the junk yard will be it's resting place when you're done with it? (the moral issue most don't care about).    Omega question is then how diligent are you prepared to be in general mechanical, air & oil maintenance? Preventing particulates and keeping them sufficiently dilute; preventing the precursors from generation, amalgamation and precipitation.    If I get a good look at the engine bay of a vehicle I have a fair idea of the owners commitment to the inside of the power train. That 30 micron WIX is still more efficient than a sieve.                 
    • It also depends on what criteria someone is using for “best” when talking filters.  Are we going off best efficiency?   Best quality/QC?  Etc. because the two may not mutually exclusive.  
    • They’re not the same wiz as 10-15 years ago.  QC has fallen pretty hard.  The XP line was never good though in the first place.    https://bobistheoilguy.com/forums/threads/wix-filter-rusted-through.386492/post-6991372   https://bobistheoilguy.com/forums/threads/i-ve-used-my-last-wix-filter.27299/   https://bobistheoilguy.com/forums/threads/looking-for-a-better-replacement-for-wix-51258.403977/   https://bobistheoilguy.com/forums/threads/convince-me-in-using-the-purolator-boss.401537/post-7420147   the forums are littered with posts and examples of not great wix filters the last couple years 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...