Jump to content

Recommended Posts

Posted (edited)

Sorry, double post. 

 

That is impressive!  I get that it's a long highway drive, but still, 29.6 has bragging rights.  May have me thinking about the LZO next time.  The torque is right where I need it for towing the boat, but I wonder how the power feels compared to my 6.2?  I haven't driven the Diesel to compare.  My silly attitude was focused on the horsepower and torque when I ordered my 2024.  I do love the 6.2 though... 

Edited by JeffKirk
Posted
9 hours ago, redwngr said:

Here's one of mine. 

One tankful.

Filled near home, crossed at Sarnia-Port Huron and refilled somewhere in NC on the way to Raleigh.  

 

image.thumb.jpeg.3ce7e54350b92dafd4fce78d2e09092d.jpeg

 

 

That is impressive!  I get that it's a long highway drive, but still, 29.6 has bragging rights.  May have me thinking about the LZO next time.  The torque is right where I need it for towing the boat, but I wonder how the power feels compared to my 6.2?  I haven't driven the Diesel to compare.  My silly attitude was focused on the horsepower and torque when I ordered my 2024.  I do love the 6.2 though... 

Posted

I decided to order a 3.0l this morning. I like the 6.2l but I don't trust it. If there wasn't a big delay on repairs, I wouldn't have any issues. But right now, if one goes, it'll be weeks waiting for a replacement. 

Posted
3 minutes ago, Jus Cruisin said:

I decided to order a 3.0l this morning. I like the 6.2l but I don't trust it. If there wasn't a big delay on repairs, I wouldn't have any issues. But right now, if one goes, it'll be weeks waiting for a replacement. 

Very much the same reason I’ve shifted away from the 6.2 myself which is a shame. 

Posted

I was getting ready to start shopping for a replacement for our '15 6.2  and decided to keep it for a while after doing some research on some of the reliability problems with the current drivetrain choices. 

 

The rear drive on the 3.0 engine for the fuel and oil pump along with the potential for ongoing oil consumption problem which GM says is normal isn't making me want that despite great fuel economy.  I've had a diesel before although older LB7, they are nice till they aren't is my experience.  Fuel additives in the Winter, gelling when it's super cold, can be harder to find fuel (good fuel), and special oil now for the 3.0 that is hard to find its all just a bit too much for me to go after right now.   

 

The 6.2 DFM and bearing failures is a non starter till GM get's it resolved and I'm not aware of any solutions yet. 

 

Then there's the 10 speed valve body wear issues that both motors could have - I think I'm better off sticking with what I have for a while longer.  Seems they should have just used the old 5 speed Allision used in the HD trucks which was bullet proof.  

 

I do realize squeaky wheels rise to the top but reliability is king and I'm not willing to throw down 60-80k on a truck that might be a PIA to own when what I have just works (knock on wood). 

Posted (edited)
5 minutes ago, Srode1 said:

The rear drive on the 3.0 engine for the fuel and oil pump along with the potential for ongoing oil consumption problem which GM says is normal isn't making me want that despite great fuel economy.  I've had a diesel before although older LB7, they are nice till they aren't is my experience.  Fuel additives in the Winter, gelling when it's super cold, can be harder to find fuel (good fuel), and special oil now for the 3.0 that is hard to find its all just a bit too much for me to go after right now.   

 

 

 

200k mi interval on the belt now.

 

As for oil consumption, IMO, its people buying these and not actually using them or idle the crap out of them or driving 1-5 miles to work at city speeds.  Rings not seating or rings getting stuck with carbon build up.  

 

Same with the 2.7, 5.3 and 6.2 consumption.  My 2.7 had a leak, fixed it and no consumption between changes, if any its maybe 1/8 qt at the most.  My leak would do about 1qt in 3000mi.  My 2018 5.3 I had, again, burned/consumed zero or near zero.  

Edited by newdude
Posted
15 hours ago, newdude said:

 

 

200k mi interval on the belt now.

 

As for oil consumption, IMO, its people buying these and not actually using them or idle the crap out of them or driving 1-5 miles to work at city speeds.  Rings not seating or rings getting stuck with carbon build up.  

 

Same with the 2.7, 5.3 and 6.2 consumption.  My 2.7 had a leak, fixed it and no consumption between changes, if any its maybe 1/8 qt at the most.  My leak would do about 1qt in 3000mi.  My 2018 5.3 I had, again, burned/consumed zero or near zero.  

I'm not trying to talk anyone out of buying one,  just sharing my reasoning for not buying a new one now.  For me it's just not a good fit for the way I  use our truck even though it get's great fuel economy.  

 

The 200K mi service interval on that belt for a $3500 repair item will probably impact the resale if you keep the truck well past it's warranty.  

 

Diesels aren't good for shorter trips I agree, they don't warm up and in the Winter it takes a long time to warm up and get heat in the cab even with a grill cover.  Do I use my truck for short trips - yep daily.  Do I take long road trips yep, and that's where this engine would shine but I don't do that more than a few times a year.  One of those will be towing and in the days before DEF that's where a diesel would definitely shine and thats why I did own one.  Towing in a truck that needs DEF will still be more economical I'm sure but it's something else a person needs to manage and any of the hands on reviews I seen agree, towing will increase DEF consumption a lot.  When I get in the truck to tow our 5000lb boat and trailer 1200 miles one way, I don't want to need to carry gallons of DEF along on the trip or deal with having to fill it when it needs it on a long towing road trip either.  I just want to fill a vehicle when it needs fuel and go.   My 6.2 tows just as well as the 3.0, and is a better fit for me.  If GM wasn't having reliability issues with their current 6.2 I would probably be driving one - but right now it's a big nope, too many problems. 

Posted (edited)
16 hours ago, Srode1 said:

I was getting ready to start shopping for a replacement for our '15 6.2  and decided to keep it for a while after doing some research on some of the reliability problems with the current drivetrain choices. 

 

The rear drive on the 3.0 engine for the fuel and oil pump along with the potential for ongoing oil consumption problem which GM says is normal isn't making me want that despite great fuel economy.  I've had a diesel before although older LB7, they are nice till they aren't is my experience.  Fuel additives in the Winter, gelling when it's super cold, can be harder to find fuel (good fuel), and special oil now for the 3.0 that is hard to find its all just a bit too much for me to go after right now.   

 

The 6.2 DFM and bearing failures is a non starter till GM get's it resolved and I'm not aware of any solutions yet. 

 

Then there's the 10 speed valve body wear issues that both motors could have - I think I'm better off sticking with what I have for a while longer.  Seems they should have just used the old 5 speed Allision used in the HD trucks which was bullet proof.  

 

I do realize squeaky wheels rise to the top but reliability is king and I'm not willing to throw down 60-80k on a truck that might be a PIA to own when what I have just works (knock on wood). 

This I completely respect and support, but only from a financial point of view.  Vehicles are a depreciating asset and a horrible strain on many households.  That said, there is no such thing as waiting out the current issues that manufacturers are having in their segment space with the EPA push to become compliant with mileage and emissions (let alone engineering to have the most horsepower, comfort, electronics, etc. over their competitors).  We are in an era where the engineering is always pushing, so todays issues that get resolved will be a new set of issues in 5 years.  Since the first vehicle rolled off the assembly line, mechanical failures have been an issue.  Heck, as I sit here, if you visit any forum whether GM, Toyota, Ford, Dodge, etc. and assume you will have the same experience, then might as well plan on never buying another new vehicle.  Forums survive and thrive on doom and gloom.  I have no data to offer, but comfortable stating that for every failure, there are many upon many that didn't.

Edited by JeffKirk
  • Like 1
Posted (edited)

yeah, forums tend to magnify problems but often where there's smoke there's fire too.  When a manufacturer's supply chain can't keep up with repair demands that's a pretty good indication there's a significant issue as is the case with the 10 speed transmission valve body and the 6.2 engine bearing failures. 

 

Platforms will continue to evolve and innovate, I'm choosing to wait until there's a higher level of understanding what the root cause and solution is for these problems before replacing a perfectly serviceable truck that meets all my needs.  It would be nice to have some of the camera features and supercruise etc, but not compelling enough to take the risk on the drive train problems for me right now.  If my truck was totaled in an accident today I would lean towards looking for a similar '15-18  6.2 as a replacement instead of one of these new ones right now. 

Edited by Srode1
Posted
On 3/6/2025 at 8:32 AM, Srode1 said:

yeah, forums tend to magnify problems but often where there's smoke there's fire too.  When a manufacturer's supply chain can't keep up with repair demands that's a pretty good indication there's a significant issue as is the case with the 10 speed transmission valve body and the 6.2 engine bearing failures. 

 

Platforms will continue to evolve and innovate, I'm choosing to wait until there's a higher level of understanding what the root cause and solution is for these problems before replacing a perfectly serviceable truck that meets all my needs.  It would be nice to have some of the camera features and supercruise etc, but not compelling enough to take the risk on the drive train problems for me right now.  If my truck was totaled in an accident today I would lean towards looking for a similar '15-18  6.2 as a replacement instead of one of these new ones right now. 

And don't forget I really believe that some people join a forum just to bash a product that probably don't even own the vehicle that the forum supports like people with 1 post that come in and say "The same thing just happened to me" only to be ever heard from again and iam not saying there isn't a problem I think they just join to create more panic.

Posted
1 minute ago, Silverado4x4 said:

And don't forget I really believe that some people join a forum just to bash a product that probably don't even own the vehicle that the forum supports like people with 1 post that come in and say "The same thing just happened to me" only to be ever heard from again and iam not saying there isn't a problem I think they just join to create more panic.

 
100%. I take it with a grain of salt. Still haven’t pulled the trigger yet. Playing the games with dealers currently. With how much inventory they all still have, they’re willing to walk away from deals over a couple hundred bucks. Onward we go. 

Posted
2 hours ago, Silverado4x4 said:

And don't forget I really believe that some people join a forum just to bash a product that probably don't even own the vehicle that the forum supports like people with 1 post that come in and say "The same thing just happened to me" only to be ever heard from again and iam not saying there isn't a problem I think they just join to create more panic.

True, but when the NHSTA gets involved there's more to it than some keyboard warriors. 

 

  • Like 1
  • 2 weeks later...
Posted

I see that you ordered your truck before I was able to post my experience.  Imo, you made the right choice getting the 3.0 Duramax.  I have a 2020 with the 6.2 and lived in San Diego from 2020 to 2023.  Diesel prices were either the same or slightly lower than 91 octane.  It's the mpg that makes the difference.  Iirc, Costco is a Top Tier Fuel Diesel provider.  Otherwise, GM recommends getting their additive whenever you fill up.  The current 3.0 produces more torque than the 6.2.  Both engines also use the same trans.  As such, they're very similar in 1/4 mile times (according to TFL Truck).  Best I ever saw in mpg with the 6.2 is 24.4 mpg.  That was a drive from San Diego to Las Vegas with the cruise set at 78mph.  Like you, I was torn on which engine to get.  I have been very happy with the 6.2, but sad that I didn't get the 3.0 (COVID and empty car lots played a factor in my purchase).  The biggest dis/satisfaction factor is how frequently I have to fill the tank.  If I could do it again I'd get the 3.0, but if I had the 3.0 I'd probably say I'd get the 6.2.

  • Like 1
  • Thanks 1
Posted
14 hours ago, Transient said:

I see that you ordered your truck before I was able to post my experience.  Imo, you made the right choice getting the 3.0 Duramax.  I have a 2020 with the 6.2 and lived in San Diego from 2020 to 2023.  Diesel prices were either the same or slightly lower than 91 octane.  It's the mpg that makes the difference.  Iirc, Costco is a Top Tier Fuel Diesel provider.  Otherwise, GM recommends getting their additive whenever you fill up.  The current 3.0 produces more torque than the 6.2.  Both engines also use the same trans.  As such, they're very similar in 1/4 mile times (according to TFL Truck).  Best I ever saw in mpg with the 6.2 is 24.4 mpg.  That was a drive from San Diego to Las Vegas with the cruise set at 78mph.  Like you, I was torn on which engine to get.  I have been very happy with the 6.2, but sad that I didn't get the 3.0 (COVID and empty car lots played a factor in my purchase).  The biggest dis/satisfaction factor is how frequently I have to fill the tank.  If I could do it again I'd get the 3.0, but if I had the 3.0 I'd probably say I'd get the 6.2.

I'm figuring if I don't like it I'll swap out a little early. I just wish the 6.2l would get warrantied in a timely fashion if they do go south. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,924
    Total Members
    8,960
    Most Online
    KirbyCo
    Newest Member
    KirbyCo
    Joined
  • Who's Online   7 Members, 0 Anonymous, 1,448 Guests (See full list)


  • Latest Articles

  • Posts

    • I will be doing that for sure, but I need to solve who has/ where I can find a bidirectional scan tool that will support OBD 1.5. I'm kicking myself because I ebay'ed a Snap On MT2500 that I didn't think I'd ever need anymore. D'oh!! I'd rather not buy another, so I'll contact a few local shops to see if they have one and how much they'd want to do the procedure. I'd rather have the ability to do it myself... I wish there was a modern tool that could do it all, but I'd have no idea what to buy.   The theory with the pulled timing is that it mimics a rich condition. The delayed spark causes incomplete burn and the O2 sensor picks up low oxygen levels. That's interpreted as a rich condition so the PCM pulls fuel and that shows up in the deeply negative fuel trims.
    • An ultra wealthy man had the most beautiful daughter. But, there was a problem. Everything she touched would melt in her hands. No matter what, Metal, Wood, Stone. Anything she touched would melt. She could not feed herself. Because of this, men were afraid of her. Nobody would dare marry her. Her father was despaired. What could he do to help his daughter? He consulted doctors, scientists and anybody who could solve this problem. Finally one of them said, "If your daughter touches one thing that does not melt in her hands, she will be cured." He was overjoyed and came up with a plan. The next day, he held a competition. Any man who could bring his daughter an object that would not melt in her hands would be given billions of dollars to marry her. Three extremely intelligent and handsome young men took up the challenge. The first brought a very heavy steel rod, But alas, when the she touched it, it completely melted in a matter of seconds. He sadly went away. The second brought a beautiful diamond, knowing diamonds were one of the hardest substance in the world and would not melt. But alas, once she held it in her hand, it melted. He too was sent away disappointed. So now, there was one left He was very nervous & sweating. He approached the daughter & said, “put your hand in my pants pocket and feel what is in there." She did exactly what he asked. She felt something very hard. She held it in her hand, squeezing it as hard as she could. It did not melt & remained extremely hard. Her father was overjoyed. Everybody was overjoyed. She was finally cured. Nothing never, ever melted in her hand again. They married and they both lived happily ever after, raising a wonderful family. Question: What was in the the groom’s pants pocket??? Answer below ↓ M&Ms of course! They melt in your mouth, not in your hand. What on earth were you thinking?
    • There's a bunch of tea leaves that you've read, but in any case the delayed timing is unusual. Not sure how that relates to the rich at idle vs. 'normal' while driving.   If you're in this deep, might be worth investigating, and re-learning the sensor. What have you got to lose? Plus, it properly fixes the timing cover leak.
    • The only problem I have seen this cause is longer crank times. 
    • Injector is being sent off today for rebuild and I estimate I'll have it back in 10 days or so.   It may not be the injector...of course...now that I've torn down the intake again. But, let's rule out the injector and replace those spider legs that have been almost rubbed through.   The truck has always had negative timing and I'm reading "normal" timing at warm idle should be +16 or so. I'm negative 16 to 25 or more, and it's always been like that since I bought it.   A light turned on upstairs last night in the old noggin. Rare, I know...   This will be wild, if it turns out to be the cause!   In 2001, according to the old service documentation, the muffler was replaced. Why? I have no idea, it wouldn't have been rusted through by then. But they did a crappy job.   In 2019, another shop replaced it and noted the prior install was poorly done on the work order. "Exhaust system vibrates on crossmember". Except...I guess they just left it be? I believe the husband, the couple who were original owners, had passed by then. Maybe she said it's just not worth it to have the exhaust system fixed and declined repairs. Very few miles were driven between 2019 and 2025.   The exhaust system vibrates heavily on the crossmember and you can feel it and REALLY hear it, even today. Not always, but at idle, it gets going pretty good sometimes.   What if....   ....What if that's enough to trigger one or both of the knock sensors? Could it be tricking the sensors into sensing knock, so it's pulling timing aggressively? Pulling timing heavily means it's firing after the piston reaches full height which means incomplete burn which means the O2 sensor is sensing a rich condition, which means I've been chasing my tail, and what I thought was an inconsequential problem (janky exhaust) has been THE issue for this truck for 25 solid years?   That would be wild. Maybe it IS wild.   The service documentation thereafter, for years, shows visits for rough idle, replacing O2's, replacing the cat, replacing plugs and wires, a misfire condition, like they could never solve the issue. The injector has been replaced 4 times in 80k miles, that's just crazy.   The secondary theory....   The engine has clearly had a leak at the front seal for a very long time (the greasy trench...). I think the truck changed hands quickly ~2025 because there's Napa receipts from someone I don't recognize in the ownership history. They apparently replaced the timing cover seal, and they did a terrible job. There's RTV smeared all over and the leak I had reduced to a weep by snugging the front oil pan bolts is now a leak again.   HOWEVER....I read about replacing the crankshaft position sensor. Any time the ckp sensor is disturbed or timing cover is removed, the truck requires relearning, and that can only be done through a bi-directional scan tool. Skippy with the RTV probably didn't do the relearn procedure is my guess. His scan tool is lost in a pile of RTV goo somewhere.   So, it's very possible the sensor has been disturbed and the truck is just running on the old learn data but not setting a code for anything. The distributor has since been replaced and so has the camshaft position sensor, so all bets are off for that thing.   In the theme of one step forward, two steps back, I returned the accumulator for the AC. The gal I've been working with at O'Really's has been great. She refunded it under manufacturer's defect and we compared it to the replacement I ordered, and sure enough, the replacement is machined very differently (and a gauge actually fits on it!).   Got it home, installed it, started vacuuming it down.... and I couldn't get good vacuum.   The high side service port, where I replaced the old GM ball valve suspecting that was a source of the previous leak....well, I've clearly exposed whatever pre-existing crack in the line where the service port is welded, and made it much worse. Blessing in disguise? Except there goes another $25, now I'm waiting for a replacement AC line.   In 10-ish days ALL the parts will be here. Rebuilt injector, new exhaust system, new cat, new high pressure AC line.   Oh, did I mention the squeaking ISN'T coming from the AC pump? The truck still squeaks when started, and there were words after I started it with the new AC pump installed. But, there was more to replacing the AC pump for just a squeak. A truck with good working AC is something of value, for the comfort alone.   I've ordered a new harmonic balancer because, 30 years is a good run for one of those. Rule it out. The squeak may be something more sinister, though. I'm worried about that ckp sensor and if it was shimmed correctly, or if the timing set was installed correctly. The squeak may be coming from UNDER the timing cover.   At this point, once I get it put back together, I'm thinking I'll take a 50 mile victory lap and then promptly put it up for sale. This truck is cursed. Betty, from beyond the grave, doesn't want anyone messing with her Blazer. Or maybe she's getting revenge for 30 years of shop visits with that thing.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...