Jump to content

2014+ Leveling Kits

bcazier

By bcazier
in Modifications & Accessories

 Share

Recommended Posts

corncob Enthusiast

corncob

Posted
Posted

I ended up giving up and busting one of mine up really good with a pickle fork (was putting on new UCAs anyway).

 

I've always broke themapart with a hammer on other trucks, but couldn't get this one to budge. I let it hang for an hour after hammering. Sprayed it with penetrating fluid. Cranked the wheel back and forth. Beat on it from every direction and every height (jacked the lca up and down at various heights) and never could get it to bust loose with a hammer. The passenger one came apart much easier. Not sure why this one was so much harder.

 

 

Sent from my iPhone using Tapatalk

  • Replies 7.7k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Saleenpowr
Saleenpowr

So i put my RC 2" level kit and Toyo 295/55/20's on this weekend. Install was simple, just like on my 2011. It definitely helps to have an extra set of hands when wedging that spacer in there. 295/

Saleenpowr
Saleenpowr

Thanks. Here is one more from yesterday. Considering we're getting 8-10 inches of rain the next two days, I won't be taking any better pics soon.  

FH212
FH212

Mine is finally done! After months of research I went with the RC 2.5" level kit front only, stock rear block. 20"x9" Fuel Nutz w/ +1 offset, 33x12.50x20 Toyo M/T tires. No rubbing, No trimming, yet a

Posted Images

dave07 Enthusiast

dave07

Posted
Posted

For those who've done their own leveling kit:

 

I've done several on my previous vehicles, and a fair amount of front end work in college, but.... I attempted to pop the upper ball joint this week, on my new Silverado, and it wouldn't budge. I used a pair of 3# hammers (one one the left side of the knuckle, the other swung from the right, and vis-versa.) Nothing! Puppy is holding fast!

 

A friend suggested that the knub on the back side of the knuckle was the appropriate target point... what's your experience?

Maybe try putting a jack under the knuckle and jack it up a little bit. Then try whacking it with a sledge.

 

 

Sent from my iPhone using Tapatalk

'17 Sierra Enthusiast

'17 Sierra

Posted
Posted

For those who've done their own leveling kit:

 

I've done several on my previous vehicles, and a fair amount of front end work in college, but.... I attempted to pop the upper ball joint this week, on my new Silverado, and it wouldn't budge. I used a pair of 3# hammers (one one the left side of the knuckle, the other swung from the right, and vis-versa.) Nothing! Puppy is holding fast!

 

A friend suggested that the knub on the back side of the knuckle was the appropriate target point... what's your experience?

Same here like the others have said. Right side popped off but the left side wouldn't no matter what I did. I was able to get the spacer in the left side without dropping the ball joint. PITA, but I got it. Also, I don't believe it's necessary to disconnect the electric steering connectors either. Those clips break super easy. Ask me how I know..

  • Like 1
KurtA Enthusiast

KurtA

Posted
Posted

Same here like the others have said. Right side popped off but the left side wouldn't no matter what I did. I was able to get the spacer in the left side without dropping the ball joint. PITA, but I got it. Also, I don't believe it's necessary to disconnect the electric steering connectors either. Those clips break super easy. Ask me how I know..

How did you install the spacer without popping the upper ball joint? I thought about trying to compress the strutt with a bottle jack while the suspension is at full droop.

Mattvand Enthusiast

Mattvand

Posted
Posted

With the opposite side still up in the air with both sway bar links disconnected, you can disconnect the bottom strut bolts and loosen the top strut bolts and just about get the spacer on without compressing. I tried that, it would have worked if I would have had a second jack or a second set of hands to help compress the shock or the coil/upper arm.

  • Like 1
Mattvand Enthusiast

Mattvand

Posted
Posted (edited)

But getting the nut on the lower strut bolt that sits under the 4wd axle will be interesting if you don't drop the knuckle.

Edited by Mattvand
  • Like 1
'17 Sierra Enthusiast

'17 Sierra

Posted
Posted

But getting the nut on the lower strut bolt that sits under the 4wd axle will be interesting if you don't drop the knuckle.

You put the bolt in from the bottom on the axle side.

'17 Sierra Enthusiast

'17 Sierra

Posted
Posted (edited)

How did you install the spacer without popping the upper ball joint? I thought about trying to compress the strutt with a bottle jack while the suspension is at full droop.

Lots of persuasion! With the RC kits being polymer, once you get a corner of it started, they tap in the rest of the way fairly easily.

Edited by '17 Sierra
SDH3BLK Enthusiast

SDH3BLK

Posted
Posted

Nice setup. Love those tires! Any room for larger size?

 

 

Sent from my iPhone using Tapatalk

Sorry never saw this, I think it can squeeze 35's just fine! Masbe with some slight trimming.

raress9596 Enthusiast

raress9596

Posted
Posted

RANCHO RS999901

Has anyone used this to replace the entire strut assembly to level my truck? I can do this easily. Otherwise I was going to go with the Bilstein shock replacement and have to get a spring compressor and all. Thanks.

  • Like 1
SuperSierra Enthusiast

SuperSierra

Posted
Posted

RANCHO RS999901

Has anyone used this to replace the entire strut assembly to level my truck? I can do this easily. Otherwise I was going to go with the Bilstein shock replacement and have to get a spring compressor and all. Thanks.

I have heard good things about the rancho quick lift other than they get rusty fast.

I want to get them as well but not sure if I'd rather get the fox ones.

 

 

Sent from my iPhone using Tapatalk

raress9596 Enthusiast

raress9596

Posted
Posted (edited)

Ordered the Rancho Quick lifts and matching rear shocks. I like the ease of install and not having to dismantle the strut. Should have them tomorrow and install them over the weekend if I have time. I've switched out strut assemblies before on many GM trucks. Shouldn't take more than a couple of hours.

Edited by raress9596
  • Like 1
Psych73 Enthusiast

Psych73

Posted
Posted

Hello everyone, I have a 2014 Sierra 1500 SLE and installed the Bilstein 5100's on all four corners. You don't have to change the rear shocks if you don't want to but that's up to you. You will need an alignment. The stance to perfect with an 1/8 of inch. Ride has since gotten better and more comfortable. Hope this helps.

  • Like 1
SuperSierra Enthusiast

SuperSierra

Posted
Posted

Ordered the Rancho Quick lifts and matching rear shocks. I like the ease of install and not having to dismantle the strut. Should have them tomorrow and install them over the weekend if I have time. I've switched out strut assemblys before on many GM trucks. Shouldn't take more than a couple of hours.

Can you do measurements of the amount of lift it adds, the rancho page says that it will make your truck able to run 35s but doesn't say what it needs to be paired with if anything.

 

I found only one video of a guy running 35s with them.

 

 

Sent from my iPhone using Tapatalk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • newdude
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By newdude · Posted

      No such thing as regenerative braking on a pure ICE vehicle.     Regenerative braking is the re-capture of energy from electric motors and stores it in the battery pack.  So hybrids, PHEV and EVs have regenerative braking.     What you are seeing is the charging system changing modes is all.  Its likely entering charge mode for some sort of reason is all.  All of the charging modes will be listed below.   As for L10 vs D.  L10 turns off automatic grade braking.  L10 puts you in control of grade downshifts where in D it will automatically do it based on brake pedal position and other factors.  Otherwise L10 and D drive exactly the same aside from that one aspect.    Battery Sulfation Mode The BCM will enter this mode when the interpreted Generator output voltage is less than 13.2 V for 45 minutes. When this condition exists the BCM will enter Charge Mode for 2–3 minutes. The BCM will then determine which mode to enter depending on voltage requirements.   Charge Mode The BCM will enter Charge Mode when ever one of the following conditions are met:   Windshield wipers are ON for more than 3 s. Climate Control Voltage Boost Mode Request is true, as sensed by the HVAC control module via serial data. High speed cooling fan, rear defogger, and HVAC high speed blower operation can cause the BCM to enter the Charge Mode. The estimated battery temperature is less than 0°C (32°F). Battery State of Charge is less than 80%. Vehicle speed is greater than 145 km/h (90 mph) A current sensor malfunction exists. System voltage is determined to be below 12.56 V When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.   Fuel Economy Mode The BCM will enter Fuel Economy Mode when the estimated battery temperature is at least 0°C (32°F) but less than or equal to 80°C (176°F), the calculated battery current is less than 15 A and greater than −8 A, and the battery state-of-charge is greater than or equal to 80%. Its targeted generator output voltage is the open circuit voltage of the battery and can be between 12.5–13.1 V. When fuel economy mode is active, the generator is not charging, only maintaining open circuit battery voltage. The BCM will exit this mode and enter Charge Mode when any of the conditions described above are present.   Headlamp Mode The BCM will enter Headlamp Mode when ever the head lamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.   Start Up Mode When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 s.   Tow/Haul Mode (if applicable) Pressing the Tow/Haul Mode button located on the center stack, the vehicle system voltage is raised and the remote (non-vehicle) battery will be charged. Having the headlamps on will raise the system voltage and if the Tow/Haul button is applied it will not serve any purpose. The voltage is regulated between 13.9-14.5 V.      
    • jaszr2
      Active Grille Delete

      By jaszr2 · Posted

      Hello from Australia Just sharing that there is now a way to delete the active shutters entirely with just a plug in module. Opens up tons of room to light bars etc.
    • jake111
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By jake111 · Posted

      I have an observation and a question... 1) I watch the voltage closely because I have had to dial in the cut-in/cut-out voltages of the battery separator to my camper.  The "smart" charging drives me nuts.  Anyway, I noticed that when coasting for a while, and especially if lightly using the brakes (though not necessary), the voltage goes up from mid/high-13 volts to mid/high-14 volts.  Then it drops back down after stopping or going again.  Consistently!   The only explanation I can come up with is REGENERATIVE BRAKING!  Well, maybe that's a little bit of an exaggeration, but it's certainly free extra battery charging.   2) Driving on mountain roads I will use L and vary the max gear.  Things straighten out and I end up in L10.  Sometimes I leave it there for a while.  Is there any difference between L10 and D?   
    • devonthegreat
      anyone interested in a 2002 Chevy Silverado 4x4 parts truck NYC

      By devonthegreat · Posted

      **SOLD** Please end or delete post. thank you
    • PBNB
      Tire pressure for 37s

      By PBNB · Posted

      Do you think this width might affect the chalk test with a higher pressure closer to 65psi? I think lowering the pressure makes sense to get the tread to lay flatter

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...