Jump to content

Recommended Posts

Posted (edited)

Here is my 17 Sierra Elevation with a 2" level I got from Amazon (aluminum blocks for under the struts) and Nitto Ridge Grappler 295/60/20 on stock wheels.  I can turn lock to lock with no contact to the liners, but I suspect under load it will rub a little.  It does hit the sway bar at full lock, but not too bad.

 

28083783089_57f922025f_h.jpg

 

28083782379_323dcb59bb_h.jpg

 

28083783689_bccaec7e1d_h.jpg

 

 

Edited by 24v
  • Like 2
Posted (edited)

After installing a Top Gun Customz 2.5” front level and an add a leaf in the rear, I’m taking the front back down to only 1” today. Reason is the ride up front bangs around more than I like for a truck with only 22k, and I believe GMC-AT who’s tried many level combos and recommends not going over 1.5” (and doing so only with under strut plates). If the rake is too much I’ll also remove the add a leaf but I’m about to haul a 4K lb trailer 1000 mi so I may hold off on the add a leaf removal. 

 

I really like the stance but the ride and other guys’ issues with ball joints and other wear have pointed me toward a Zone 1.5” body lift—if I want to get back to this look after removing most of the front leveling kit. 

 

Anyone else have ride quality issues resolved by using less of a leveling kit?

4DF7F015-3B0D-40A8-8002-50F874F36334.jpeg

Edited by Shredder15
Clarification
Posted

I asked a ton of questions on this forum so I figure I owe everyone a report-out.... 

 

I was very hesitant and pretty skeptical, but finally installed Billy 5100s all around on top setting in front along with the ReadyLift rear 2.25 blocks and had aligned. I immediately notice the difference visually from about 30 yards away and is exactly what I hoped for; looks good and noticeable increase in wheel well space. Fitting slightly bigger AT tires shouldnt be a problem. I measured but pretty roughly as I wasn't too concerned about the fractions. I got 2" min. up front and obviously a solid inch in back. 1" of rake left. Wouldn't of minded a little more rake either. You can also feel the height difference sitting in the truck. I've owned a couple 2500s, one of which was lifted on 35s so I'm used to the height difference. I do believe I'll need to adjust the headlights down just to be safe. Haven't been flashed yet but can tell they're pointing slightly higher. 

 

Driving is where this leveling setup really impressed me.  My round trip commute is 80 miles and includes roads of every type from highway to gravel.  I'd read all the reviews about a much firmer ride and feeling more of the small stuff in the road. You can feel a little more in the road, maybe, but not at all in a bad way.  To me It really feels really planted and just right.  Better grip, less bouncy at the same time.  Body roll is almost eliminated around bends with speeds in the low-mid range, still noticeable at higher speeds but improved nonetheless. Obviously it doesn't nose dive quite as bad during the quicker stops either. 

 

My biggest fear was driveline caused vibrations due to the 3 degree rear block taper. Cross my fingers I haven't felt anything yet. Would still like to get on a much smoother highway to be absolutely sure though and stop worrying about it. 

 

I do tow a 3 place but very light snowmobile trailer at the max; hoping it doesn't squat much if it all. 

 

 

Posted

I too needed a leveling kit and researched and found Moto-Fab, they had great reviews and these were only $35.00 Dollars. Installation was pretty straight forward requiring the removal of tie rod end and the upper and lower control arms.  But I was a little nervous as the kit blocks measured only a tad over 1 inch but somehow i missed the day they taught Geometry in school but it raised my front end exactly 2 inches, had the alignment done and i love the way the truck sits and it didn't change the ride that much, in fact it stiffened it up a little which i like instead of the cushy ride.   I still have just a small amount of rake but i am please overall, and didn't spend a lot of money. 

Posted
2 hours ago, Fall Sniper said:

Would like to level my 2018 Denali but unsure about messing with the magna ride and don’t want a harsh ride.

 

 

Sent from my iPhone using Tapatalk

 

I installed a 2.5" Level from Suspensionmaxx with 2" Blocks in rear of my 2017 Denali. It rode just like factory before I put the 10Ply Ridge Grapplers on and it still rides great. I rode around for 2 weeks before tires and couldn't tell a difference except truck looked like it skipped leg day..lol

 

20180126_141940.jpg

  • Like 4
Posted
I installed a 2.5" Level from Suspensionmaxx with 2" Blocks in rear of my 2017 Denali. It rode just like factory before I put the 10Ply Ridge Grapplers on and it still rides great. I rode around for 2 weeks before tires and couldn't tell a difference except truck looked like it skipped leg day..lol
 
20180126_141940.thumb.jpg.a70ea9880709d683919231bdc384042f.jpg

Thanks for that info. Truck looks great.


Sent from my iPad using Tapatalk
Posted

Thanks for that info. Truck looks great.


Sent from my iPad using Tapatalk

With the 2” in the back and 2.5 in the front, do you still have a slight rake down in the front?


Sent from my iPad using Tapatalk
Posted
3 minutes ago, Fall Sniper said:


With the 2” in the back and 2.5 in the front, do you still have a slight rake down in the front?


Sent from my iPad using Tapatalk

Yes it is a little less than factory but I pull a boat year round and didn't want the squat. I'm glad I did as some look like they are a little high in the front. The suspensionmaxx has the bracket relocator for the magneride and have great instructions. If you decide to do it yourself let me know and I can give you a few tips to make it go quick! Here is a side and front shot

20180126_142000.jpg

20180122_092428.jpg

Posted
3 minutes ago, DenaliLegend said:

Yes it is a little less than factory but I pull a boat year round and didn't want the squat. I'm glad I did as some look like they are a little high in the front. The suspensionmaxx has the bracket relocator for the magneride and have great instructions. If you decide to do it yourself let me know and I can give you a few tips to make it go quick! Here is a side and front shot

20180126_142000.jpg

20180122_092428.jpg

Truck looks good!  What size Ridge Grapplers?

Posted
Yes it is a little less than factory but I pull a boat year round and didn't want the squat. I'm glad I did as some look like they are a little high in the front. The suspensionmaxx has the bracket relocator for the magneride and have great instructions. If you decide to do it yourself let me know and I can give you a few tips to make it go quick! Here is a side and front shot
20180126_142000.thumb.jpg.7097c87c2366c709971a5bf7754e9345.jpg
20180122_092428.thumb.jpg.d65c74ace88ca5022462337db301af53.jpg

Thank you. The side shot shows it well. Did you reprogram your speedo when you switched to taller tire? I had a bully dog in my last truck which was a diesel.


Sent from my iPhone using Tapatalk
Posted
Just now, CHSRebleForLife said:

Truck looks good!  What size Ridge Grapplers?

Thanks! 285/55r22 and get a small rub on full lock on liner only

Posted
1 minute ago, Fall Sniper said:


Thank you. The side shot shows it well. Did you reprogram your speedo when you switched to taller tire? I had a bully dog in my last truck which was a diesel.


Sent from my iPhone using Tapatalk

No not yet as I can't decide if I want to void warranty with a full blown tune or just go to dealer have them recalibrate speedo. These things are addictive as I already have a new grill being made and can't stop mods..lol

 

Posted
No not yet as I can't decide if I want to void warranty with a full blown tune or just go to dealer have them recalibrate speedo. These things are addictive as I already have a new grill being made and can't stop mods..lol
 

[emoji106]


Sent from my iPhone using Tapatalk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • First off, I'm not trying to just get easy advice/fixes for the issues I've noticed so far.  I'll be combing through the site via searches and such, and if past experiences are any indication, should find what I need.  For the sake of conversation, though, I figured I'd post the handful of things I've noticed in the 12 hours since buying my 2010 SLE CCSB.     Indicator lights: Airbag and TPMS.  The tire pressures aren't reading for any of the wheels, so I'm pretty certain the sensors were either removed, are damaged, or are otherwise inoperable.  I used to mount and balance tires 25 years ago but am pretty much ignorant when it comes to TPMS.  My 2006 didn't have the sensors and this might be the fourth vehicle I've owned that does.     Radio: Rear speakers aren't working.  I removed the driver's side rear door panel and checked the speaker and wiring.  I also removed the sill and b-pillar covers to check the wiring.  A few minutes of Google Fu showed that this is potentially a head unit issue.    Switches: Power mirrors don't turn left/right.  I ordered replacement driver's door switches that should arrive tomorrow.  The windows and locks work but it was only about $20 for all of them.  The driver's side rear window switch lets the window down but won't put it back up.  I think the passenger rear doesn't work at all.  In the coming days/weeks, I'll break out my multimeter to check all of that.   Unknown wiring harness: There's a box attached to the front driver's side of the engine compartment, right where the second battery shelf is located.  There are three plugs, one of which looks like it fits a standard headlight-style bulb (9007 or similar).  It doesn't look like it's plugged into anything.  I'll do some digging and if I don't see anything elsewhere on the site, post some pictures here.   Unknown plugs on brake booster: There are at least two female plugs on the brake booster that aren't being used.  I think it might be a replacement/aftermarket, so maybe those are used for a different application, as there don't seem to be any unplugged harnesses and no indicator lights are on.   Little squeaks when turning: Sounds almost like a bushing around the bed of the truck.  I'll have to pay close attention as I get more familiar with the truck.   Clunk on acceleration: possibly the infamous drivetrain clunk.  My 2006 had it and I'm just not familiar enough with this truck yet to fully grasp what it is.   Anyway, my apologies for the vague and all over the place post.  This truck is new to me, and it's been four years since I drove my 2006.  With 200k miles, I know I'll need to learn this truck quickly to avoid having any major issues, despite being confident it's got much more life to it.  My 2006 had nearly 320k on it when I parked it (nearly 300k of which I put on the truck), and it was still drivable then, though I suspected the head gasket might have blown.  I'd hoped to have that truck back by now, but it's gone forever, as I detailed in my reintroduction thread.  
    • I always drive in Sport mode. With more driving, I am finding the initial response when accelerating is much quicker now🖕 Lou
    • Is it an optical illusion in the pic or is the truck really squatting that much horribly?
    • My initial introduction was here.  It's hard to believe that I last posted in February 2013, having just deployed to Kyrgyzstan.  Since then, I've retired from the military and the 2006 Sierra SLT Z71 that first brought me to these pages was lost.  I went forward to Afghanistan in March 2013 and did a lot of sitting behind a computer on brigade staff.  Within 18 months of getting back to the States, I was selected for Drill Sergeant duty, after which I moved back to Virginia (my home state and where I served from 2004-2008).  That '06 Sierra did a lot of driving between Louisiana, Georgia, and Virginia, and ended up with nearly 320k miles by 2022.  By then, the registration had been expired for a couple of years, but the pandemic had all but eliminated tickets for such transgressions.  Admittedly too, I usually drove my wife's SUV or son's car the 2-3 times a week I had to report to work.  Teleworking sure was fun while it lasted.   I started my retirement leave four years ago and stored the Sierra at my sister's house.  A big mess was made when her fiancé passed while she was taking care of business out-of-state in late-2024, and his son pretty much mismanaged everything to do with the estate.  Even so, I was assured that my truck was safe... until it wasn't.  I found out that my truck had been scrapped about four months after the son took over everything.  There's nothing I could do; I'm 1000 miles away and it was technically abandoned property since he'd even trespassed my sister from her own house (she had no claim to it as she wasn't married, and the fiancé was the sole owner).     Anyway, today I got my second Sierra.  This is a 2010 SLE 2WB CCSB with a little over 200k miles on it.  It's got the 5.3L I'm familiar with and should handle what I need it for.  Hauling stuff that won't fit in the Transit Connect (yep, I sold out, but that's the wife's vehicle) and towing a few times a year tops.  The price seemed decent, considering how much people sell their trucks for in the Deep South: $4500.  I've seen similar trucks listed for more than double that.  I got it from a coworker who left his tag on until we transfer the title next week (Louisiana requires a notary for transfers), so I've been driving it all day.  The rear speakers don't work, which is one of the things that brought me back to these forums earlier.  I can't say how active I'll be as a poster, but I'll be scouring the archives while I find out every little thing I can about the 2010s and particular nuances/problems with my truck.   It's definitely not a GMC, but I got another Willys Jeep a few months back as well, so I'm almost at the same place I was when I first joined gm-trucks.com.  My old 1960 DJ3A was sold back around 2010 or 2011; my current Jeep is a 1946 CJ2A.  So, I've got a slightly newer GMC and a much older Jeep.  I kind of wish I still had that F-250 I had way back when too.  The Dakota is long gone and was technically my brother's truck, though I had it registered and insured.  The F-250 had to go when my grandmother's house was foreclosed on due to mismanagement around 2012 or so.     Hopefully anyone that made it this far isn't too annoyed.  I tend to be long-winded, but I'll be doing more reading than posting in the coming months.
    • There was a recall on the tailgate in general for opening on its own. Mine has a cap on it and it won’t let the tailgate open.   My tailgate has two holes in the top of the tailgate. I filled them in with silicone sealant. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...