Jump to content

2014+ Leveling Kits

bcazier

By bcazier
in Modifications & Accessories

 Share

Recommended Posts

Fix29 Enthusiast

Fix29

Posted
Posted
Is the failing ball joints mainly on the upper control arms or on the lower control arms as well? I thought I was fixing the ball joint problem with the cognito UCAs and the CV angles with the diff drop kit for the 3" level kit. I don't see many people replacing the lower control arms, are those not so much of an issue with a leveling kit as the UCA? 
While going with over 2.5" naturally is going to put things at greater angles and more stress on parts the lower ball joints don't end up at nearly as severe an angle as the upper ball joints do, thus why these kits come with upper control arms typically to help those angles and provide a heavier duty ball joint.

Sent from my SAMSUNG-SM-G890A using Tapatalk

  • Replies 7.7k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Saleenpowr
Saleenpowr

So i put my RC 2" level kit and Toyo 295/55/20's on this weekend. Install was simple, just like on my 2011. It definitely helps to have an extra set of hands when wedging that spacer in there. 295/

Saleenpowr
Saleenpowr

Thanks. Here is one more from yesterday. Considering we're getting 8-10 inches of rain the next two days, I won't be taking any better pics soon.  

FH212
FH212

Mine is finally done! After months of research I went with the RC 2.5" level kit front only, stock rear block. 20"x9" Fuel Nutz w/ +1 offset, 33x12.50x20 Toyo M/T tires. No rubbing, No trimming, yet a

Posted Images

jgraves13 Enthusiast

jgraves13

Posted
Posted
Is the failing ball joints mainly on the upper control arms or on the lower control arms as well? I thought I was fixing the ball joint problem with the cognito UCAs and the CV angles with the diff drop kit for the 3" level kit. I don't see many people replacing the lower control arms, are those not so much of an issue with a leveling kit as the UCA? 

Lower control arms as well. When you go over 2.5" it really puts them at a bad angle. The uppers are suspect as well, even with the new uppers. If you think about all the down travel in the suspension that you lose with a 3" kit, hitting the bump stop on the upper arms puts a lot of stress on other parts, especially the balljoints as they try to keep the suspension held together. And with a 3" kit, you'll be hitting those bump stops a lot more often.

Personally that .5" more to go to the 3" kit really isn't worth it, even though they "fix it". Their fix isn't really a fix, more of a not-so-great bandaid


Sent from my iPhone using Tapatalk
Fix29 Enthusiast

Fix29

Posted
Posted

Are there any companies out there that do aftermarket lower arms? Just curious as I don't recall seeing any. I will post a few pictures of my truck for reference. I'm sure all brands vary in how much the upper arms correct the angle of the upper ball joint but I feel like the Fabtech's did a really nice job. The first picture is my truck with the Readylift 2.25" level only. The second picture is with 3.6" lift, Fabtech upper control arms, and diff drop. 3da8a6544d104d8a606b54e1603b7466.jpg0ac75c9a6fff7655d3226cefe728fc6b.jpg

Sent from my SAMSUNG-SM-G890A using Tapatalk

jgraves13 Enthusiast

jgraves13

Posted
Posted
Are there any companies out there that do aftermarket lower arms? Just curious as I don't recall seeing any. I will post a few pictures of my truck for reference. I'm sure all brands vary in how much the upper arms correct the angle of the upper ball joint but I feel like the Fabtech's did a really nice job. The first picture is my truck with the Readylift 2.25" level only. The second picture is with 3.6" lift, Fabtech upper control arms, and diff drop. 3da8a6544d104d8a606b54e1603b7466.jpg0ac75c9a6fff7655d3226cefe728fc6b.jpg

Sent from my SAMSUNG-SM-G890A using Tapatalk




Not unless you go with a midtravel or long travel kit to my knowledge


Sent from my iPhone using Tapatalk
  • Like 2
vhreso Enthusiast

vhreso

Posted
Posted

Those of you doing 2.5" levels on stamped UCA, are you having any issues?  I wanted to do 2.5" on my 2018 but im not sure if the UCA would be ok?  Thanks for the help!

 

MyChevy18 Enthusiast

MyChevy18

Posted
Posted (edited)
On 8/14/2013 at 3:59 AM, bcazier said:

For those of you that have already installed a leveling kit...

 

Which did you go with and why?

 

Do the new aluminum suspension parts impact the install?

 

I hope to get one on my truck in the next couple weeks but want some insights first.

If you stay on same OEM set of tires and wheels...leveling kit is okay.

on my 2018 Silverado 4x4, i DIY a 2” leveling kit front. The one you put on top of the strut. Easy job, bolt in/bolt out. You just need 2 set of jack. 1 to raise the truck, 2 to raise/lower the front suspension to help you installing the spacer andd taking the strut&coil out. And a little bit of cutting the threads.

truck looks better as leveled.

NOW...i Installed 35s sets of tires...nitto terra grappler with 20x12.5 with -19offset....looks great...RIDE is as smooth as OEM

Drawback with tire/wheels setup. Its impossible to bring the truck for some real offroading. Due to “clearance issues”

My 7 inch Lift kit from Rough Country will installed this week.

9A213AB6-7746-4CC0-B60F-756B33562445.jpeg

Edited by MyChevy18
Add info
Jorge Garcilazo New Member

Jorge Garcilazo

Posted
Posted
On 9/20/2018 at 6:47 PM, langston1726 said:

 I’d say you’re good man. You’re replacing the ucas and doing a diff drop. Most guys that run the Motofab 3” don’t do either.  Btw I’ve got some 0-2.5” lift Procomp coilovers I’d consider selling if you’re looking to go that route instead of spacers. I need new ucas to run them and it’s going to be awhile before that happens.

 

 

Sent from my iPhone using Tapatalk

 

 

 

 

I'm in the process to level out my stock 2014 Gmc short bed z71 4x4 what's my best route to take and what would I need to make it best i can?

 

langston1726 Enthusiast

langston1726

Posted
Posted
I'm in the process to level out my stock 2014 Gmc short bed z71 4x4 what's my best route to take and what would I need to make it best i can?    

 

  I’ve leveled the last 4 GM crewcab trucks I’ve had using a variation of spacers, Bilsteins, and a body lift. I’d say out of all those the best set up is probably running Bilstein 5100s at on the highest setting which should get you around 1.85”-2” of lift and removing the rear lift blocks. This should get you pretty much dead level, all the suspension components should still be happy and your ride will be as good or better than factory. I’m currently running a Rough country 2” level with the rear block removed. It sits about .5”-.75 higher in the front. Most people don’t care for the nose high look but it’s really hard to tell with this set up. You can spend anywhere from $100 to over $3000 on a leveling kit. It all depends on your budget and what you want out of the truck.

 

My current truck

b2c718c810626bb3d02b77cbc319769c.jpg

 

2” level/Bilsteins on second level

73779115f3aff982bb8afda85fb9fb9e.png

 

2” level/1.5” body lift

766c846a45a98592a1cb33546735da34.png

 

2” level/Bilsteins at second level

de0efcf76b1f57e1aedf874ddb8d0c5d.jpg

 

 

Sent from my iPhone using Tapatalk

 

 

 

 

SNAFU88 Enthusiast

SNAFU88

Posted
Posted (edited)
On 9/25/2018 at 6:53 AM, langston1726 said:

 

73779115f3aff982bb8afda85fb9fb9e.png

 

 

 

 

 

 

 

Sent from my iPhone using Tapatalk

 

 

 

 

What size tires on this truck? 285/75-17?  Looks fantastic.  

Edited by SNAFU88
langston1726 Enthusiast

langston1726

Posted
Posted
What size tires on this truck? 285/75-17?  Looks fantastic.  


Correct. Toyo At 2 Xtreme. I had to trim with the 0 offset Method. I miss that set up


Sent from my iPhone using Tapatalk
SNAFU88 Enthusiast

SNAFU88

Posted
Posted
2 hours ago, langston1726 said:

 


Correct. Toyo At 2 Xtreme. I had to trim with the 0 offset Method. I miss that set up


Sent from my iPhone using Tapatalk

 

Safe to say that my '15 Sierra w/ a 2" RC kit up front & 2" rear block would need some trimming to run 285/75-17 KO2s?  They're listed as 33.9" tall and my wheels are 17x9 et -6.  

jgraves13 Enthusiast

jgraves13

Posted
Posted
Safe to say that my '15 Sierra w/ a 2" RC kit up front & 2" rear block would need some trimming to run 285/75-17 KO2s?  They're listed as 33.9" tall and my wheels are 17x9 et -6.  


Definitely would need to trim some. I went with 295/70/17 which is about a 33.6" and I had to trim with 0 offset rims on the RC 2" spacer


Sent from my iPhone using Tapatalk
Michael71009 Enthusiast

Michael71009

Posted
Posted

Here's mine after the Bilstein 5100s we're installed. Measurements before and after are the 2nd picture
4ae87964639c63d22326162bf2c1827f.jpg3682a24b45209ac0e0401b2433ffcd62.jpg

Sent from my SM-N950U using Tapatalk

cwhitehurst34 New Member

cwhitehurst34

Posted
Posted

2" Rough Country kit for me. I just installed it on my 2018, and it was super simple and looks great! The truck is still about 1/4" low in the front but just standing back and looking at it, it looks perfectly level. Made it look like it should have come from the factory! And $50 bucks on amazon. https://amzn.to/2OkYKZv

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Tyler Gibbs
      Travel Trailer 2024 2500 HD 6.6 Gas Engine ?

      By Tyler Gibbs · Posted

      The curb weight on a 1 ton crew cab long bed is around 7k lbs.  Now, I don't know where you went to school but 9k is not more than 2x 7k lbs. More than 2x 7k lbs would be 14k+.   With that said, obviously yes you're going to feel a 9k lb trailer when slowing down.  I already said, when accelerating.  When changing lanes?  No.  But if you look at the context of what was quoted, the original person said, "after a mile or two..." which means that would be after the accelerating portion and you're driving a generally steady pace.  Please do learn to read and comprehend.
    • sFrank
      2026 Silverado Range AFM DFM ECU loaction

      By sFrank · Posted

      So I purchased the Range unit for my 2026 and I am seeing different locations suggested for the ECM . Can anyone confirm wither under hood, left side or right side or behind the wheelwell?
    • No F-bdy Bs
      Dave's Auto (custom engine builder) tear down of L8T

      By No F-bdy Bs · Posted

      Like I've said before. Di and Carbon buildup is not that big of a concern. Engine had minimal buildup, and that engine was obviously not super well maintained. Do regular oil changes, and you're gtg as long as the rest of the truck lasts. Also, the High Pressure FP that people ****** about, but can't tell you why.  Now, I wish they'd trash the variable oil pump. No real world issues with them, but I'll gladly eat whatever miniscule MPG it's saving me in favor of more oil at all RPMs.    Curious to see his assessment of the 7.3 compared to the 6.6. I expect he'll praise the port inj, but from a structural standpoint, the 6.6 is as robust as any engine out there.    Not to take away from the 7.3. I feel it's equally as good as the 6.6.     As to heat on the rear cyls, I'd have to see numerous examples before I'd say it's an issue. Especially not knowing the history of that engine. For all is known, they could have blown a rad hose, and ran it hot, and the 2 rear cyls may be the first to get hot in a low coolant situation, but not be an issue aside from that. 
    • Donstar
      Navigating senior years.

      By Donstar · Posted

      "Life is getting back to normal."    I'm driving again and all new joints are operating as expected for this stage of recovery.   My most recent joint replacement still requires a lot of attention but experience has taught me that time will quiet the remaining pain.  I joked with my surgeon that another joint replacement would take my mind off my most recent surgery and he responded by saying the next will be a hip!  There are no plans for another surgery but, unlike me, I don't think he was joking!  I certainly wouldn't refuse further replacement  if required but hope to spend time out of the "post-op"  period.  I can't stress enough that if you have been recommended for total hip, knee or shoulder replacement that you welcome the offer.  Post-op "recovery" may sound daunting and painful, however, this is far better than the insidious erosion of mobility you are currently experiencing.  Imagine what it would feel like to wake up most mornings feeling better and more mobile than you did the previous day!  Prior to my first surgery in June 2025, even getting out of bed was becoming a formidable task.  Since the day after my first surgery, I get out of bed everyday easily and unassisted.  Making the switch to feeling a little better each day rather than a little worse, is hugely motivating!
    • Coastie05
      ‘25 Silverado purchase- back to dealership for bumper/radio issue

      By Coastie05 · Posted

      Hope it all works out for you. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...