Jump to content

Recommended Posts

Posted (edited)

Thank for the info^^ I'm going to have to look for some vids.

Sounds like your set up may be for me.

 

With just my Borla muffler, I only hear it really good on cold startups and when I punch it. Would love to be able to hear it just a tad more on driving in and idling.

 

Well to give you more of an idea, I park on the street in front of my house and when I remote start it from my bedroom (back end of house) I hear it just fine. Same as when I've done it from my backyard. So I know when it starts up without having to look at the truck lol. So I know as long as the remote is in range it's loud enough for me to be able to hear. It's not a "I can barely hear it" type of thing either. But, it's also not so loud that you can't hear anything else while driving. Even with the windows down I can get by with the radio only being about 1/3 and 1/2 volume. To me it's perfect and have no complaints.

 

Here's a vid I made of it. The only thing it doesn't show is the V4 drone which you'll hear in an aggressive exhaust that doesn't have the flapper valve.

 

https://www.youtube.com/watch?v=mQxoOtyr1qs

Edited by SouthernSilveradoGuy85
Posted

Great video^ Was that a cold start?

 

No, I had driven for about 15 minutes and the temp was in the 70s I believe. A cold start up it's a tad louder because of the RPMs obviously, but as you know it doesn't take long for the RPMs to drop.

Posted (edited)

Also want to add that i purchased the Intune by Diablo. It has pre programmed tunes on the handheld device. I was amazed at how it woke my truck up!

My point bringing up the Intune is that you can turn off the V4 mode...keeping the truck firing on all 8cyl..all the time...no drone!

 

Im sure most of you know this, but wanted to mention it as an extra mod along with the Airaid and Borla muffler...its a must buy

Edited by lemmuhj
  • Like 1
Posted

Also want to add that i purchased the Intune by Diablo. It has pre programmed tunes on the handheld device. I was amazed at how it woke my truck up!

My point bringing up the Intune is that you can turn off the V4 mode...keeping the truck firing on all 8cyl..all the time...no drone!

If I understand correctly the newer computers do like a time stamp when you alter the ECM. I chose to purchase a "Range" device that leaves no footprint in the ECM. Just another option if your worried about warrant issues down the road.

Posted

If I understand correctly the newer computers do like a time stamp when you alter the ECM. I chose to purchase a "Range" device that leaves no footprint in the ECM. Just another option if your worried about warrant issues down the road.

When the stock tune is reloaded with the Intune onto the ECM, the only way that GM can tell that the computer was accessed is if they are looking for it. Reloading stock tune leaves no real footprint other than one saying that the computer was accessed. Same thing that appears when a dealer checks the computers. So it doesn't look out the ordinary

 

This is what I have been told by a worker at a dealer who had a tuner on his 14'

  • Like 1
Posted (edited)

 

When the stock tune is reloaded with the Intune onto the ECM, the only way that GM can tell that the computer was accessed is if they are looking for it. Reloading stock tune leaves no real footprint other than one saying that the computer was accessed. Same thing that appears when a dealer checks the computers. So it doesn't look out the ordinary

This is what I have been told by a worker at a dealer who had a tuner on his 14'

This is good for many to know. I myself won't go the route of a tune as I did this before and seen no real gain in fuel or performance. The one thing I did see was tighter shift points but I am not one to bump up the shift pressure more than 30%... I did a trans build with servos and shift kit etc in my 05 Avalanche and it was by far more rewarding and costly.

Edited by No Tyme
Posted (edited)

When the stock tune is reloaded with the Intune onto the ECM, the only way that GM can tell that the computer was accessed is if they are looking for it. Reloading stock tune leaves no real footprint other than one saying that the computer was accessed. Same thing that appears when a dealer checks the computers. So it doesn't look out the ordinary

 

This is what I have been told by a worker at a dealer who had a tuner on his 14'

In the duramax world, GM requires and ECM 'snapshot' before approving major engine warranty work.

 

I think that counts as 'looking for it'

Edited by redwngr
Posted

There have been a lot of "In cab" videos posted, but to my ears, none have captured what the real sound is in the cab. I have never heard a video that even remotely depicts the V4, helicopter sound. I think you have to actually ride in the truck to truly "hear/feel" the V4 thing. To me it's a "feeling", as much as a sound. You know how you sort of "feel" the bass in a good stereo....pretty much the same idea. Maybe if you have a real good speaker system, or headphones, you might get closer, but just standard computer speakers.........I don't think so.

 

Its a sound hard to describe.........it drives some poeple crazy, and others don't seem to mind it. My 2007 Silverado had a Magnaflow system, and the V4 thing was certainly noticeable, but really it didn't bother me all that much, and I guess I just got used to it over time. Like I said, you need to hear it in the cab of a truck, In my opinion, for what it's worth, I don't think the V4 sound can be reproduced in a sound clip with any accuracy.........you have to hear it for yourself.

 

Well stated. I agree 100%. As I've stated before, I like the sound of both V8 and V4 modes with the 14" Magnaflow.

 

A friend of mine (who happens to like a ride a quiet as a Rolls) said... "That is unbearable! You ruined it!"

 

I just smiled and said... "Love it."

 

Beauty is in the ear of the beholder!

  • Like 3
Posted

Hey guys, I got a video of the 18" magnaflow. I don't like the video at all. Makes the "drone" sound like an unbearable noise. I'm currently in the process of trying to get it to sound more realistic to give y'all a proper video! Hopefully I can get a good video that properly depicts the sound soon.

Posted (edited)

With just my Borla muffler, I only hear it really good on cold startups and when I punch it. Would love to be able to hear it just a tad more on driving in and idling.

 

Be careful what you wish for...........these new 2014 trucks are exceptionally quiet inside, and this really affects the inside sound of a performance exhaust. I have the GM Borla system on my truck, and one day had my son drive it while I was outside. I had him do all the usual moves like take off from a stop, drive by at 40/50mph and then hit it etc.

 

I was very surprised as the sound was much louder outside than I would have expected. The inside sound to me was very reserved, and I also had some reservations that it may have been too quiet. Not the case........much more sound when listening from the outside.

 

I would think if you get the sound up to the level where you can hear it inside at a normal cruising speed, the sound would have to be extremely loud outside. I would get someone else to drive your truck and you listen from the outside before making any major changes........you just might be surprised.

 

Just my thought.

Edited by revitupfaster
  • Like 2
Posted

Be careful what you wish for...........these new 2014 trucks are exceptionally quiet inside, and this really affects the inside sound of a performance exhaust. I have the GM Borla system on my truck, and one day had my son drive it while I was outside. I had him do all the usual moves like take off from a stop, drive by at 40/50mph and then hit it etc.

 

I was very surprised as the sound was much louder outside than I would have expected. The inside sound to me was very reserved, and I also had some reservations that it may have been too quiet. Not the case........much more sound when listening from the outside.

 

I would think if you get the sound up to the level where you can hear it inside at a normal cruising speed, the sound would have to be extremely loud outside. I would get someone else to drive your truck and you listen from the outside before making any major changes........you just might be surprised.

 

Just my thought.

Wow...extremely good advice, thank you.

 

Im actually considering getting a Borla S Type cat back. From all the vids ive seen, it may be just right.

 

Looks like ill be getting my wife to do some drive bys first:)

Posted (edited)

After reading thread from start to end I decided to go with the following:

1. Magnaflow muffler part no 12909

2. Red Tail Performance RTP-070B

3. Eliminate Exhaust Flapper Valve

 

I took advantage of a coupon through Advance Auto so muffler is $119 including shipping.

Might be too tame for some but as long as it's a little rumbly on start up and idle should be fine for me.

Thanks to everyone who wrote their experiences.

Edited by Lgetz
  • Like 2
Posted (edited)

Here's a video from Airwelldone. This is of his Y pipe installed and he's revving the engine

 

th_E25B3E54-CF37-4F6C-A823-0EED68187B11_

 

Edit: at least tapatalk users will need to follow the link to photobucket to watch, just a heads up.

Edited by Mike1220

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Monday looks like a good day for the dealer to test an ac issue. Hopefully it all turns out good.
    • Paid $2.72 for E85 today.
    • Welcome back! No, it definitely doesn't pass the sniff test. Even "ceasefire" needs an alternative definition these days.    $5.29 at Kroger today
    • That makes sense, and I think you are describing the real product problem. Capturing data is the easy part. If the owner or technician has to manually dig through five minutes of millisecond-level logs, the product has already failed. The device would be at the ECM harness, not at the OBD port, so I agree that data retrieval and event marking need to be thought through carefully. The way I am thinking about the architecture is: The recorder itself should not depend on a phone, app, Bluetooth, Wi-Fi, or cloud connection to capture the event. It should always keep a local rolling buffer and lock the event locally. A button, phone app, or small cabin device would only act as an event marker. If the driver feels a stumble and presses the button 10–30 seconds later, the pre-buffer has to already contain the useful data. For data retrieval, the practical options would be a sealed service USB lead, Wi-Fi download, or a phone/cabin companion device. I would not expect the owner to remove the ECM-side module or work with raw files directly. The cloud or AI side would be for interpretation, not for capturing the event. The truck may have no connection when the issue happens, so the evidence has to be saved locally first. After that, cloud processing could help decode the data, compare it against baselines, and generate a readable report. For the first version, I would keep the automatic triggers conservative and objective: driver event marker bus-off error passive voltage drop / brownout device reset FIFO or queue overflow a normally periodic message disappearing side-to-side communication mismatch, if the topology supports that For “learning normal,” I agree with your point, but I would not want to overclaim it as automatic root-cause diagnosis at first. A realistic first step would be learned baseline comparison for that specific vehicle and operating condition. For example, a value would only be compared against similar conditions: RPM range load / MAP throttle position gear / vehicle speed coolant and oil temperature battery voltage AFM/DFM state, if decoded and validated Then the report could flag things like: this periodic message disappeared compared with its normal timing this value deviated from this vehicle’s normal range under similar conditions the same abnormal pattern repeated after the same type of event the anomaly occurred together with voltage, oil-pressure, misfire, or communication changes But I would still call that “abnormal pattern detected,” not “replace this part,” unless there is enough validated repair data behind it. So the intended product would not be “here is a huge log.” It would need to be an event package: what triggered the capture how much pre/post data was preserved what changed before and after the event whether the device itself reset, overflowed, or saw a bus error selected graphs around the event raw data only as supporting evidence From your perspective, what would make this kind of report useful instead of just another datalog? For example: What are the top 5 parameters or events you would want highlighted first? Would you trust a learned baseline for that specific vehicle, or would you prefer fixed thresholds? How much false-positive flagging would be acceptable before you stopped looking at the reports? What would a one-page report need to show for an independent shop to take it seriously? For misfire, AFM/DFM, oil pressure, or U-code complaints, what would you want the tool to flag automatically?
    • 2024 Silverado 2500 HD LTZ grille no camera Parts list   84603331 84913656 84913657 84913654 84913655 84911567 84911568 85646092 85646093 85797921 85797922   11570637  x10-15   grille/bumper bolts 11546500  x10      grille clips 11571006  x10      push/retainer clips 11546454  x6       nut retainers 11611609  x6       M5 bolts 11610700  x6       molding/trim retainers
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...