Jump to content

Recommended Posts

Posted
Yes and is it a rc or cc?
Mine is a rc. Truck is fighting me a bit today, getting the caltracs installed, but I'll get those pics for you as soon as I can put the weight of the truck on the axle

Sent from my SM-N950U using Tapatalk

  • Like 1
Posted
8 minutes ago, lovelessjl said:

Mine is a rc. Truck is fighting me a bit today, getting the caltracs installed, but I'll get those pics for you as soon as I can put the weight of the truck on the axle

Sent from my SM-N950U using Tapatalk
 

Are you at a 4/6? I havent seen your truck 

Posted
7 hours ago, Nasty said:

Can you get me a quick picture.  I need to see the distance between your frame and axle pad in the rear. If you can hold a tape .measure in there that would be even better 

Is this what you need? Sorry, it's sideways DSC_0811.thumb.JPG.80a16c7288b8f4fbb937d2f21fc41413.JPG

  • Like 1
Posted
36 minutes ago, Nasty said:

Are you at a 4/6? I havent seen your truck 

He posted it on the previous page :lol:

Posted
Are you at a 4/6? I havent seen your truck 
I was at 4/5, but once I get the truck back on the ground, I'll be at 4/6.f5768463c11f6a95f587946c13f213e3.jpg

Sent from my SM-N950U using Tapatalk

  • Like 1
Posted
35 minutes ago, qwank said:

Is this what you need? Sorry, it's sideways DSC_0811.thumb.JPG.80a16c7288b8f4fbb937d2f21fc41413.JPG

That's at 5.  I'd you can do the same at 6 that would be perfect. Becsuse I might lift mine from 7to 6 in the rear 

Posted
Thank you! My truck is a 4x4 so I had to do it a little different than most guys with 2wd trucks. I have 2" spindles with stock shocks and 2" lowering springs up front, and a flip kit in the rear set at 5 in that pic but next week I'll be bringing the rear to 6".

Sent from my SM-N950U using Tapatalk


I had to do the same thing on my ‘16 CC Lovelessjl due to having 4WD... I currently sit at 4/7 based on my measurements from the ground... I used MaxTrac everything with the same setup you did...d80c762a4754682c3310a296a0454787.jpeg


Sent from my iPhone using Tapatalk
  • Like 1
Posted
23 minutes ago, Xpensive Chevy said:


I had to do the same thing on my ‘16 CC Lovelessjl due to having 4WD... I currently sit at 4/7 based on my measurements from the ground... I used MaxTrac everything with the same setup you did...d80c762a4754682c3310a296a0454787.jpeg


Sent from my iPhone using Tapatalk

Are you doing to notch it? I'm at 4/7 in my rc and I almost need a notch.  Cc sit lower than rc

Posted
Are you doing to notch it? I'm at 4/7 in my rc and I almost need a notch.  Cc sit lower than rc

No issues with my setup so I’m not gonna notch it... My flip kit is set at 5” but I had my blocks removed so I’m between 6”-7” in the rear...


Sent from my iPhone using Tapatalk
  • Like 1
Posted

Here is frame to pad, without a bump stop with the flip kit set at 6"a2bdfb7f65e882cdd4e3448c65f7462e.jpg

Sent from my SM-N950U using Tapatalk

Posted
Here is frame to pad, without a bump stop with the flip kit set at 6"a2bdfb7f65e882cdd4e3448c65f7462e.jpg


I’ll have mine on a lift on Thursday so I’ll measure mine as well...


Sent from my iPhone using Tapatalk
Posted
10 minutes ago, lovelessjl said:

Here is frame to pad, without a bump stop with the flip kit set at 6"a2bdfb7f65e882cdd4e3448c65f7462e.jpg

Sent from my SM-N950U using Tapatalk
 

1 more measurement while you're at it  center of hub to the fender. In the rear please.    I think I'm lifting mine to 6

Posted
31 minutes ago, lovelessjl said:

Here is frame to pad, without a bump stop with the flip kit set at 6"a2bdfb7f65e882cdd4e3448c65f7462e.jpg

Sent from my SM-N950U using Tapatalk
 

this makes me want to got to 6'' since it's only 1/2'' difference in height.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • It wouldn’t have happened if the government hadn’t mandated outrageous fuel mileage standards. It does very little for the consumer. It adds cost. Back during Covid there was a chip shortage. They gave a rebate for your truck if it didn’t have the chip to turn on cylinder deactivation. It was 50$ because at best you may see 1/2 a mile increase per gallon. Splitting hairs each fuel mileage trick wasn’t mandated. The government doesn’t do the engineering work and say use this until it’s already in use and they like it. The fuel mileage was mandated. And those add ons the results. There’s a mandate and they are the results.
    • It was never mandated.  Ever.    Automakers were incentivized to install it by getting CAFE credits to help with their vehicle fleet fuel economy scores.  They were being handed money/CAFE credits to install it.  Which is NOT a mandate.       The current admin removed the incentives that were behind them installing it.       
    • Are you playing Slide Down endlessly but your score is still low? Are you constantly crashing into obstacles as the game speed increases? Don't worry, this article will share 5 invaluable tips to help you master the race and impress your friends. Golden Rules 1. Look one step further. The mistake of 90% of new players is only staring at their character. The secret of experts is to look towards the top of the screen (where the slide is about to appear). This gives your brain an extra 0.5 - 1 second to process the situation and determine the direction of movement before the obstacle approaches. 2. Use gentle movements; don't swipe too hard. Slide Down is very sensitive. Moving your finger too forcefully or with excessive amplitude will cause your character to be thrown off course or crash into a wall. Practise moving your finger with small, decisive, and precise movements. 3. Don't be greedy for gold in dangerous locations. Gold coins are tempting for buying skins, but life is more important. If you see a gold coin right on the edge of a cliff or next to a spike trap, ignore it. Our goal is a High Score, and your score only increases if you survive. 4. Make the most of Power-ups. During the slide, you'll encounter items like Magnets (attract gold) or Shields (temporary invincibility). Never miss them! Especially the Shield, it's your "get out of jail free card" to help you get through those deadly fast sections. 5. Stay calm when speed peaks. When your score exceeds 500 or 1000, the game speed will be very fast. At this point, don't try to think logically; let your natural reflexes work. Take deep breaths and don't panic. Apply these 5 tips to your next game, and your leaderboard will surely improve dramatically. Good luck climbing the Slide Down leaderboard!
    • If you use compressed air regularly, one problem you cannot ignore is moisture. Water in the air line can cause rust, unstable air pressure, poor tool performance, and even damage to sensitive equipment. That is why I highly recommend using a desiccant air dryer. A desiccant air dryer is designed to remove moisture from compressed air by using drying materials such as activated alumina or molecular sieve. Compared with basic water separators, it can achieve much lower dew points, making it especially useful for applications that require dry and stable air. For workshops, painting systems, pneumatic tools, CNC machines, laser cutting equipment, and industrial production lines, a desiccant air dryer can make a big difference. It helps protect equipment, improve air quality, reduce maintenance costs, and extend the service life of the whole compressed air system. Another advantage is reliability. Many desiccant air dryers are built for continuous operation and can maintain stable drying performance even in demanding environments. For users who care about long-term efficiency and equipment protection, this is a smart investment. When choosing a desiccant air dryer, I suggest paying attention to air flow capacity, working pressure, dew point performance, regeneration method, and maintenance requirements. A good model should match your compressor system and actual air consumption. Overall, if moisture is causing problems in your compressed air system, a desiccant air dryer is definitely worth considering. It is practical, efficient, and highly useful for anyone who needs clean, dry, and reliable compressed air.
    • My brand new 2007 Silverado's wax frame was rust from end to end partway through it's SECOND winter here in MA. That stuff is completely useless.    
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...