Jump to content

Center console swap?

quickvert1

By quickvert1
in Modifications & Accessories

 Share

Recommended Posts

ravageur1972 Enthusiast

ravageur1972

Posted
Posted

ravageur1972,

 

I also have the manual transfer case. Any pointers/observations that you can make? Is there a boot below the floor shifter that keeps road debris and water from coming up? Did you modify the lever at all?

 

Sent from my STV100-1 using Tapatalk

You only have to remove the plastic trim where 4h 4l and 2h is write. It is seal so nothing will come inside . Once console will be install you will have to built a shaft to fit over the oem because the angle won't be OK but it is not hard to do.....I drive mine since a long time now and use my 4x4 often and no problem at all and easy to shift

  • Like 1
  • Replies 1.9k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

darkfox1
darkfox1

OK.. mine's in.   Here's a writeup, cos I haven't seen one so far.   1. remove the "ash tray" and cig. ligther in your dash with 3 t-10 torx screws, and 2 clips. 2. Remove the radio trim, clips i

dla
dla

I always wanted a RCSB with buckets and a center console...   Received and installed mine yesterday. Very straight forward, thanks for all who posted instructions and part numbers.   Possibly to h

o7bodybagged
o7bodybagged

Finally the console is complete now ready for the install and see what other problems I run into

Posted Images

MWZotti Enthusiast

MWZotti

Posted
Posted

You only have to remove the plastic trim where 4h 4l and 2h is write. It is seal so nothing will come inside . Once console will be install you will have to built a shaft to fit over the oem because the angle won't be OK but it is not hard to do.....I drive mine since a long time now and use my 4x4 often and no problem at all and easy to shift

Do you have a picture of the shaft you built or did you just leave it stock without the handle?

 

Sent from my STV100-1 using Tapatalk

ravageur1972 Enthusiast

ravageur1972

Posted
Posted

Do you have a picture of the shaft you built or did you just leave it stock without the handle?

 

Sent from my STV100-1 using Tapatalk

 

I still plan to make one but I also love the hidden arm. Obviously it is harder to shift without the handle but even that I love it ...maybe if I become weaker I will built one lol

MWZotti Enthusiast

MWZotti

Posted
Posted

Does anyone have part numbers for the 2016 console with the wireless charger?

  • 2 weeks later...
ember1205 Senior Enthusiast

ember1205

Posted
Posted

following

 

There's a "Follow this topic" button at the top on the right if you don't want to post just to follow a thread...

  • Like 2
Liquidfx17 Enthusiast

Liquidfx17

Posted
Posted

I stopped at my buddys dealership last night to research this alittle more. As i was attempting to just to the OEM route. Not sure the swap would be that forward. Here are a couple diagrams of the console. As you can see in the Diagram, there is a wiring harness all ran threw there. However GM does not have the part # associated with it yet. Also, for anyone that is wanting to attempt the OEM console with the wireless charger the part # we found for the lid is 23450838.

 

20160304_085609_zpsju6vkfhq.jpg

 

20160304_085623_zps4wp4uutq.jpg

MWZotti Enthusiast

MWZotti

Posted
Posted

I stopped at my buddys dealership last night to research this alittle more. As i was attempting to just to the OEM route. Not sure the swap would be that forward. Here are a couple diagrams of the console. As you can see in the Diagram, there is a wiring harness all ran threw there. However GM does not have the part # associated with it yet. Also, for anyone that is wanting to attempt the OEM console with the wireless charger the part # we found for the lid is 23450838.

 

20160304_085609_zpsju6vkfhq.jpg

 

20160304_085623_zps4wp4uutq.jpg

 

Is the part number for the entire center console assembly for the 16 the same as the 15? (the one without the wireless charger lid) I believe the part numbers are 23466980 & 23466999. Not entirely sure what the difference between the 2 part numbers are except the price.

 

GM Parts Direct 23466980 CONSOLE ASSEMBLY, W/O DENALI, W/O REAR DVD, BLACK $338.83 Shows diagram as well as what vehicles it fits.

GM Parts Direct 23766999 CONSOLE $314.76 No diagram or compatible vehicle chart.

harveyfamily Enthusiast

harveyfamily

Posted
Posted

I'd love to do this to my 2015 Sierra! Does anyone know if the wiring changed in 2015 and this is more of a plug and play now?

Liquidfx17 Enthusiast

Liquidfx17

Posted
Posted

I'd love to do this to my 2015 Sierra! Does anyone know if the wiring changed in 2015 and this is more of a plug and play now?

Did you happen to read any of this?

Nobody has been able to verify this. But from the research ive done, it does appear the 16 has a different harness completely then a 15. So its not looking like a plug n play setup.

Danny_Sierra Enthusiast

Danny_Sierra

Posted
Posted

Can one of you guys that already have installed this please text me. I'm lost on this. I've gone through all of the forum and it just throws me off. 9727680582

Danny_Sierra Enthusiast

Danny_Sierra

Posted
Posted

Ok. I've had my center console on for about 3 weeks now. But I don't have it connected. Looks nice though. But to make this short and simple. The "jumpseat harness" is the one that I fished out of the jump seat and connects to the floor? And also I need to take out my radio to get the other harness?

DCazares Enthusiast

DCazares

Posted
Posted

You don't need to remove the radio to get another harness. Only the jump seat harness is spliced where needed to power almost everything needed.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • mandrautomotive
      Light Up the Trail From Above: 50" PRO for the Hummer EV

      By mandrautomotive · Posted

      Hey everyone,   For anyone looking at roof-mounted lighting for the Hummer EV, we wanted to share our M&R Automotive 50" PRO Roof Light Bar for the 2022+ GMC Hummer EV.   The curved 50" bar sits close to the windshield rather than sticking way up above the roofline. The mounting position is designed to keep the setup relatively streamlined while minimizing wind noise and maintaining full use of the factory windshield wipers.   A few details:   50" curved PRO light bar Fits 2022–2026 GMC Hummer EV Spot + driving beam pattern TIR optics White main beam Amber DRL backglow Approximately 15,410 measured lumens through the lens Mounts to factory accessory locations No cutting or drilling required Wiring runs down the A-pillar toward the AUX connections Designed to minimize wind noise Lifetime warranty Off-road use only     The 50" is an interesting middle ground for anyone who wants the visibility and mounting position of a roof bar without stepping all the way up to the larger 60" setup. For the Hummer EV owners here, would you go with the 50" for the lower-profile look or step up to the full 60"?  
    • Glava2876
      What did you do to your "other" car (aka musclecar) today

      By Glava2876 · Posted

      My son got a hatchback withe the aero package for like 17k new. Great little car with amazing MPH
    • Jsdirt
      What did you do to your "other" car (aka musclecar) today

      By Jsdirt · Posted

      Yeah, I've given up years ago with that! I was able to load a few when I first joined the site sometime around '07. Then after maybe 20 pics, it said I exceeded the limit. Now every pic I try to post says I've "exceeded 1mb".   ONE MB??? That's Windows 95 ******, lol!! 
    • KARNUT
      What did you do to your "other" car (aka musclecar) today

      By KARNUT · Posted

      I get the same results with pictures. Then I figure it out. Then I forget. Screw it.
    • Jsdirt
      What did you do to your "other" car (aka musclecar) today

      By Jsdirt · Posted

      I guess I'm the only one on this forum who can't get effing pics to load here! Do you have to resize them to post, or am I just blocked from uploads?   I have the same luck with automotive electronics ... but this is the ONLY site on the net that I have this problem!   I'd post pics of what I'm working on ... but I CAN'T! 🤬       Just fabbed up the kickdown cable (had to extend the cable mount WAAAY out from the throttle shaft to get a full pull), and parts arrived for the fuel lines on the 940 carb conversion project. Should be able to drive this thing by the end of the day. If not for work, I'd have had this thing done SIX weeks ago.   Got the jetting sorted out last week. Had a real bad tip-in bog that I couldn't seem to correct. Friggin float height was over 11mm too HIGH! eBay purchase, so no wonder everything is screwed up right out of the box! I ended up with a larger dual-squirt accelerator pump jet anyway instead of the single. Also moved the 70 primary idle jet (4 sizes too big out of the box) to the secondary idle circuit, and installed a 57 in the primary. Runs great on the fuel bottle!    Still using the computer for ignition. Going to drive it first and see if I want to go through the project of installing an intermediate shaft with a distributor drive gear, so I can install a block-mounted distributor and run points, 100% computer free. I should do that anyway just from a simplicity / reliability / tunability standpoint. The electronics left me stranded last year a couple times! I can't tweak the timing to my liking right now because of the computer. Tried twisting the cam-driven distributor already ... and the damned thing just reverts back to where it was! That's infuriating. But if it runs well enough I might save that for next season.   Just driving it in and out of the shop to work on other projects, it feels 1,000% more responsive with the carburetor. Also fires MUCH faster when cranking. Can't wait to drive it and see if I got more than 114 ponies, lolol.   Hopefully these don't go 404 like the last post ... https://postimg.cc/gallery/MjhrmZS   Seems like that site went back to dial-up internet! Maybe they'll fix that some day ...

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...