Jump to content

Center console swap?

quickvert1

By quickvert1
in Modifications & Accessories

 Share

Recommended Posts

  • Replies 1.9k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

darkfox1
darkfox1

OK.. mine's in.   Here's a writeup, cos I haven't seen one so far.   1. remove the "ash tray" and cig. ligther in your dash with 3 t-10 torx screws, and 2 clips. 2. Remove the radio trim, clips i

dla
dla

I always wanted a RCSB with buckets and a center console...   Received and installed mine yesterday. Very straight forward, thanks for all who posted instructions and part numbers.   Possibly to h

o7bodybagged
o7bodybagged

Finally the console is complete now ready for the install and see what other problems I run into

Posted Images

FourThor Enthusiast

FourThor

Posted
Posted

e434b91e4389a3b64f609aec1707c147.jpg

All done, love it. Best upgrade so far.


Sent from my iPhone using Tapatalk

  • Like 1
FourThor Enthusiast

FourThor

Posted
Posted

How long did it take to deliver ?


Sent from my iPhone using Tapatalk


About 6 days from order being placed to being delivered.

I ordered through GMPartsNow though.


Sent from my iPhone using Tapatalk
  • Like 1
Scott Fish Enthusiast

Scott Fish

Posted
Posted


About 6 days from order being placed to being delivered.

I ordered through GMPartsNow though.


Sent from my iPhone using Tapatalk

I did gmpartsdirect. Friday is day 13 no update


Sent from my iPhone using Tapatalk
Scott Fish Enthusiast

Scott Fish

Posted
Posted


About 6 days from order being placed to being delivered.

I ordered through GMPartsNow though.


Sent from my iPhone using Tapatalk

What year is yours Mine is 2016 Black interior. What is the parts list.


Sent from my iPhone using Tapatalk
FourThor Enthusiast

FourThor

Posted
Posted

Mines a 2018, ordered the 2018 console which is the exact same as the 2016 except it has the newer version of the wireless charger.

Here’s my parts list:
49774875c4faeafbd0d22a29e7deeb27.jpg


Sent from my iPhone using Tapatalk

  • Like 1
Scott Fish Enthusiast

Scott Fish

Posted
Posted
Mines a 2018, ordered the 2018 console which is the exact same as the 2016 except it has the newer version of the wireless charger.

Here’s my parts list:
49774875c4faeafbd0d22a29e7deeb27.jpg


Sent from my iPhone using Tapatalk

What were the cables for. I didn’t order any. It appeared in the diagram I received they were included


Sent from my iPhone using Tapatalk
FourThor Enthusiast

FourThor

Posted
Posted
57 minutes ago, Scott Fish said:


What were the cables for. I didn’t order any. It appeared in the diagram I received they were included


Sent from my iPhone using Tapatalk

Routing the USB's from the HMI so everything works like stock. these are detailed in PGamboa's thread about this. 

  • Like 1
Johnny01 Enthusiast

Johnny01

Posted
Posted

What were the cables for. I didn’t order any. It appeared in the diagram I received they were included


Sent from my iPhone using Tapatalk
Johnny01: what was the shipping on it?

Sent from my SM-G935V using Tapatalk

Johnny01 Enthusiast

Johnny01

Posted
Posted
Finally have mine installed 50829297359bcaf783bbe1f3df50279c.jpg


Sent from my iPhone using Tapatalk
Where did you order from?

Sent from my SM-G935V using Tapatalk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • SwitchBladeSierra
      AUX switch install

      By SwitchBladeSierra · Posted

      Update for anyone following:    Installed everything as shown in diagram. Opted for 8 AWG from Battery Positive to a 50A resettable inline breaker. 8 AWG is tied into to 2x 12 AWG wires feeding a 6 way fuse bus in parallel (manufacturer’s design of what I purchased).    4 of the 6 fuses available for circuits are tied to terminal 30 of each relay. I tied a jumper from one of my spare circuits off the bus to terminal 86 of each relay. The trigger, terminal 85, was pulled from my interior by way of T-Taps from the X61A-X5 pins 10, 11, 17 and 23. This was the hardest part of the job. Even with the X61A unbolted and the X5 removed - there was VERY little wiggle room.  I added back up lights that I want to come on with my cargo lamp - but when I would check continuity between S48A-X1 pin 18 to its respective landing point on the X61A-X5 it triggers the factory relay… Instead I opted for a add-a-fuse on the passenger interior fuse panel (fuse location 10 - cargo lamp) and ran it through the boot on the driver side to my load. Did this to avoid introducing any electrical gremlins.   Note: Please check for continuity between the S48A-X1 and the X61A-X5. In my case wire colours were not the same as other’s who have posted. To do a continuity check you need a Multimeter. Completely disassemble the S48A-X1 and remove the brown face plate off the X61A-X5 by way of a flat head screwdriver - this was the only way I could get any results.   The outputs, terminal 87 of the relays, were fed into a junction box and landed at Individual studs and were labelled Aux 1-4.    At this point, all you need to do is run wire to your loads and bring them to ground. I created a negative bus in the engine bay, all my negatives land here.    For anyone having issues with all of your new aux switch lights coming on with the press of one - I noticed this only to be an issue when the battery wasn’t hooked up to my relays? No idea why, but it was quickly corrected by having my system buttoned up and functional.     
    • jgaudet99
      Tire psi

      By jgaudet99 · Posted

      Well I ordered the Autel ts508, and it won't work on my truck I tried all the 2023 and everything it just says vehicle not supported lol   I'm able to send this unit back, so I'm going to do that, then I'll just stop into a some tire shops and if none of them are able to do it, I guess ill have to spend a bunch of money to get a good scanner..... Thanks GM lol
    • B07
      Needing this part.

      By B07 · Posted

      Don't need the air tube but that's how everyone sells them. Most places won't remove that one piece and sell it alone. No money to be made. Hoping someone swapped theirs out for a CAI and no longer wants it. Not asking anyone to give it away. Offering to buy it but I don't need the tube. It's held on by a hex head screw and nut. Been all over eBay. 
    • Tyler Gibbs
      PF63 Oil Filters Going Away?

      By Tyler Gibbs · Posted

      Wait, you guys are changing your oil???
    • newdude
      Needing this part.

      By newdude · Posted

      If you need that mount looking piece.  You need the air tube.       Cheapest one I see on eBay - 2007-2014 GM Silverado 1500 Air Cleaner Outlet Duct Assembly 5.3L OEM 15901934 | eBay     Same price but free shipping - 2009-2014 CADILLAC ESCALADE 6.2L AIR CLEANER OUTLET DUCT ASSEMBLY 15901934 OEM | eBay

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...