Jump to content

Bilstein shocks thread

yanzhixiang

By yanzhixiang
in Modifications & Accessories

 Share

Recommended Posts

Powerlines Enthusiast

Powerlines

Posted
Posted

Hello all, just bought a 14 z71 2wd. Interested in upgrading to the 5100's all the way around. I have a few questions,

 

Do i need to change the springs too or are the stock ones ok?

 

I can use these to effectively level the truck if i want to right?

 

Thanks

 

Sent from my SM-N920V using Tapatalk

Keep the springs and yes the ride height adjustable 5100's will essentially level your truck

  • Replies 2.8k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

bwilloby46
bwilloby46

I put the bilstein 5100s on the rear of my 14 High Country with a new 2" block a few weeks ago. Ride is unbelievable compared to stock. Liked it so much I got the adjustable 5100s for my front, remove

schloppy
schloppy

Hello, I'm not new to the forum but I just joined and figured I'd contribute to the community.   2016 Silverado 1500 "Z71" removed rancho's and swapped with Bilstein 5100's all around. So after d

Jullian is not my name
Jullian is not my name

I just got done with installing my 6112's on my 2014 GMC Sierra Crew Cab.  Reading some install guides on here really helped, along with printing some Chilton Repair guide torque specs that I got from

Posted Images

noleguy83 Enthusiast

noleguy83

Posted
Posted

Keep the springs and yes the ride height adjustable 5100's will essentially level your truck

Perfect thanks!

 

Sent from my SM-N920V using Tapatalk

cpttimerestraint Enthusiast

cpttimerestraint

Posted
Posted

I just installed the 4600s on the rear and they are awesome. Night and day difference. Now I am trying to figure out replacing the fronts.

 

Sent from my SM-G900V using Tapatalk

Barnes16 Enthusiast

Barnes16

Posted
Posted

Just installed the 5100s on the front at the highest setting which gave me +2" at the front wheel wells. I was measuring 35.5" in the front and 39" in the rear before the install.

 

I was a little nervous about going to the highest setting because of a lot of the comments about the the ride being poor at that height. The ride is much better than stock. I am new to these trucks so I might just not know any better though.

 

b24da5d298a19ce07e19f3d0a4af94ea.jpg

 

 

Sent from my iPhone using Tapatalk

  • Like 2
Powerlines Enthusiast

Powerlines

Posted
Posted

Just installed the 5100s on the front at the highest setting which gave me +2" at the front wheel wells. I was measuring 35.5" in the front and 39" in the rear before the install.

 

I was a little nervous about going to the highest setting because of a lot of the comments about the the ride being poor at that height. The ride is much better than stock. I am new to these trucks so I might just not know any better though.

 

b24da5d298a19ce07e19f3d0a4af94ea.jpg

 

 

Sent from my iPhone using Tapatalk

Good to hear. Getting all 4 replaced tomorrow with stock 18's as well.

srgjigpog Enthusiast

srgjigpog

Posted
Posted (edited)

Just installed the 5100s on the front at the highest setting which gave me +2" at the front wheel wells. I was measuring 35.5" in the front and 39" in the rear before the install.

 

I was a little nervous about going to the highest setting because of a lot of the comments about the the ride being poor at that height. The ride is much better than stock. I am new to these trucks so I might just not know any better though.

 

b24da5d298a19ce07e19f3d0a4af94ea.jpg

 

Sent from my iPhone using Tapatalk

Any pictures of the rears installed?

Edited by srgjigpog
Barnes16 Enthusiast

Barnes16

Posted
Posted

Any pictures of the rears installed?

I only did the fronts right now.

 

 

Sent from my iPhone using Tapatalk

tootall87 Enthusiast

tootall87

Posted
Posted

 

Thanks for posting that. We do text during normal business hours! Or call us at that number. Or email us! Or Pm US, or Message us on facebook.

 

Got your text Corey, you ordered with Spencer which means your shocks should be shipping out today via Bilstein. Youll see them before the weekend.

 

Thanks!

 

Anybody home?? I've texted, emailed, called with no answer. I ordered on 5/7.

spencer52356 Enthusiast

spencer52356

Posted
Posted

Good Luck Tootall87, I placed my order on April 26th. I did receive the fronts finally but now I'm waiting on the rears. I did finally get ahold of Robert at MRT and he said he would call his rep @ Bilstien and get back to me but that was early last week and I have yet to get an answer. I called Bilstien myself yesterday and was told the rears are on backorder and 5 weeks out. Don't expect any communication because it's nonexistent. Sure would of been nice if there website could inform us that things are on back order when placing it in the cart.

  • Like 1
Bvonscott Enthusiast

Bvonscott

Posted
Posted

??? Man I ordered my rear 5100's from Amazon and got them in 2 days. And they even sent a replacement for one that was the wrong model for my truck and they sent a free replacement the next day. So I have an extra free shock lol. I got the 33-238319

tootall87 Enthusiast

tootall87

Posted
Posted

Good Luck Tootall87, I placed my order on April 26th. I did receive the fronts finally but now I'm waiting on the rears. I did finally get ahold of Robert at MRT and he said he would call his rep @ Bilstien and get back to me but that was early last week and I have yet to get an answer. I called Bilstien myself yesterday and was told the rears are on backorder and 5 weeks out. Don't expect any communication because it's nonexistent. Sure would of been nice if there website could inform us that things are on back order when placing it in the cart.

Got a call from him as well. Similar story, rears on backorder. Sending me the fronts now, rears when they get in. A simple email explaining that would cease all confusion and frustration.

Powerlines Enthusiast

Powerlines

Posted
Posted (edited)

Just had all 4 put on the truck and ended up with a 1.5" rake with the fronts being at the highest setting(was thinking it would be less). I also noticed the boots were installed up but I thought I read that a 2016 should go boot down? What difference if any does that make?

 

Before

4ad52f4634efbacd03e4ee2538ed3490.jpg

 

After

ae22968f5d36aa806ca668f37c94cc69.jpg

 

 

Rears

e7ec45e47a177e0c5a8990919c770f45.jpg

Edited by Powerlines
Barnes16 Enthusiast

Barnes16

Posted
Posted

Just had all 4 put on the truck and ended up with a 1.5" rake with the fronts being at the highest setting(was thinking it would be less). I also noticed the boots were installed up but I thought I read that a 2016 should go boot down? What difference if any does that make?

 

Before

4ad52f4634efbacd03e4ee2538ed3490.jpg

 

After

ae22968f5d36aa806ca668f37c94cc69.jpg

 

 

Rears

e7ec45e47a177e0c5a8990919c770f45.jpg

From what I have read, the Bilstein stickers should be right side up so they can be read which would be boot down. I don't know what kind of difference it makes though.

 

I also ended up with 1.5" of rake. Actually that is only the drivers side. My rear passenger side sits almost 1" lower than the driver for some reason; not sure what I am going to do about that or what is causing it yet.

 

 

Sent from my iPhone using Tapatalk

Powerlines Enthusiast

Powerlines

Posted
Posted

From what I have read, the Bilstein stickers should be right side up so they can be read which would be boot down. I don't know what kind of difference it makes though.

 

I also ended up with 1.5" of rake. Actually that is only the drivers side. My rear passenger side sits almost 1" lower than the driver for some reason; not sure what I am going to do about that or what is causing it yet.

 

 

Sent from my iPhone using Tapatalk

Thanks for the info. Got ahold of the shop and although he said it's doubtful they installed then upside down, they'll swap them around next week. Here's some info I found on the orientation

 

http://www.truckspring.com/blog/post/2014/05/28/can-i-mount-bilstein-shocks-upside-down

mookdoc6 Senior Enthusiast

mookdoc6

Posted
Posted

Count me in on the 5100's! I liked the shocks so much for the rear I bought the fronts almost immediately. After testing the OEM's the other day when I swapped out the passenger side shock was already sticking 3/4's on travel? Junk, most of you have already commented and the factory Shocks are straight JUNK!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • C. Hart
      Exhaust Question

      By C. Hart · Posted

      I have seen different people in different places post different sizes of exhaust as stock for my 2014 Sierra L83. Some say 2.5 some say 2.75. I am considering replacing the muffler with a Dynomax Super Turbo, perhaps 17739.  I had the factory L83 5.3 replaced with another L83 5.3 from Jasper Engines. I also put new Walker Cat / Y pipe on. I would appreciate opinions suggestions about what would be a good muffler setup. My main interest is a low rumble and the best flow / fuel mileage I can get. Not interested in straight through glass packs or loud exhaust. Those days are way behind me now.  Thanks Guys.  
    • newdude
      Cold start Miss, oil in cylinder

      By newdude · Posted

      Its coolant disguised as oil.   TSB 20-NA-166 -  20-NA-166 1..3   "To inspect for this concern, add coolant dye to the system, run the engine through warm up, pressurize the cooling system after warming the engine to operating temperature (let the engine cool overnight) and inspect the suspect cylinder with a borescope for coolant dye evidence. At times it may be necessary to remove the head for inspection. If the head casting line is the concern, the intake port will be wet with a coolant oil mix"     I'd say its the head, and its either leaking at the casting line and dripping down the intake into the cylinder, or its another spot on the casting itself at the cylinder that is getting wet.  
    • asilverblazer
      Cold start Miss, oil in cylinder

      By asilverblazer · Posted

      Can you sample the pooled liquid, enough to confirm it is oil?   ...That its not fuel or coolant.   Also, make sure combustion gases aren't entering the cooling system.   Simply put, either oil being pushed up past the rings (this really isn't possible), oil leaking past the head gasket, oil leaking past the valve, oil entering through the intake air path. If none of this is likely - it may not be oil.   What could be likely is the fuel injector leaking down. A puddle of gas would still smoke and rough idle. (Same cylinder has the same problem after injector replacement?)   What is the crank time first thing in the morning, when the puddle would be present? Does it seem like the high pressure fuel pump needs an extra second or two to rebuild the pressure that injector 8 may have let bleed off? Check the fuel pressure via a scanner prior to starting the engine.    
    • Donstar
      Navigating senior years.

      By Donstar · Posted

      Good information!  I didn't know about the dementia aspect and asked for a general for my second knee. I'd heard that recovery room time is usually shorter with a general.   The anesthesiologist talked me out of it and I had the spinal.  Inconvenience and/or discomfort is a small price to pay for reduced risk!
    • garagerog
      Navigating senior years.

      By garagerog · Posted

      This is for those over 70 years of age contemplating joint replacement surgery involving general anesthesia. Even some 55 yrs. ago when I took my pharmacology class the dangers of developing dementia in the elderly that had general anesthesia were beginning to be recognized. Over the years there has been some refinement in the cautionary warnings, avoid general anesthesia if possible if you've had close to 10 priors, especially over the age of 70 and/or a family history of dementia. I'm not including the twilight anesthesia induced by propofol often used in cytoscopies or colonscopies. Seriously think about seeing a neurologist and undergo cognitive testing before proceeding if any of those criteria apply to you. Spinal anesthesia may be an option in some cases. I'm in the above camp and although I could use a new right knee, I get fidgety according to a prior orthopedic surgeon when the bone saw spools up or maybe it was the smell of saw blade meeting bone, anyhow I may have one general anesthesia left in me which I will pocket for now and I'm choosing mind over mobility, anyway where did I leave my damn cane!

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...