Jump to content

Bilstein shocks thread

yanzhixiang

By yanzhixiang
in Modifications & Accessories

 Share

Recommended Posts

Powerlines Enthusiast

Powerlines

Posted
Posted

Hello all, just bought a 14 z71 2wd. Interested in upgrading to the 5100's all the way around. I have a few questions,

 

Do i need to change the springs too or are the stock ones ok?

 

I can use these to effectively level the truck if i want to right?

 

Thanks

 

Sent from my SM-N920V using Tapatalk

Keep the springs and yes the ride height adjustable 5100's will essentially level your truck

  • Replies 2.8k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

bwilloby46
bwilloby46

I put the bilstein 5100s on the rear of my 14 High Country with a new 2" block a few weeks ago. Ride is unbelievable compared to stock. Liked it so much I got the adjustable 5100s for my front, remove

schloppy
schloppy

Hello, I'm not new to the forum but I just joined and figured I'd contribute to the community.   2016 Silverado 1500 "Z71" removed rancho's and swapped with Bilstein 5100's all around. So after d

Jullian is not my name
Jullian is not my name

I just got done with installing my 6112's on my 2014 GMC Sierra Crew Cab.  Reading some install guides on here really helped, along with printing some Chilton Repair guide torque specs that I got from

Posted Images

noleguy83 Enthusiast

noleguy83

Posted
Posted

Keep the springs and yes the ride height adjustable 5100's will essentially level your truck

Perfect thanks!

 

Sent from my SM-N920V using Tapatalk

cpttimerestraint Enthusiast

cpttimerestraint

Posted
Posted

I just installed the 4600s on the rear and they are awesome. Night and day difference. Now I am trying to figure out replacing the fronts.

 

Sent from my SM-G900V using Tapatalk

Barnes16 Enthusiast

Barnes16

Posted
Posted

Just installed the 5100s on the front at the highest setting which gave me +2" at the front wheel wells. I was measuring 35.5" in the front and 39" in the rear before the install.

 

I was a little nervous about going to the highest setting because of a lot of the comments about the the ride being poor at that height. The ride is much better than stock. I am new to these trucks so I might just not know any better though.

 

b24da5d298a19ce07e19f3d0a4af94ea.jpg

 

 

Sent from my iPhone using Tapatalk

  • Like 2
Powerlines Enthusiast

Powerlines

Posted
Posted

Just installed the 5100s on the front at the highest setting which gave me +2" at the front wheel wells. I was measuring 35.5" in the front and 39" in the rear before the install.

 

I was a little nervous about going to the highest setting because of a lot of the comments about the the ride being poor at that height. The ride is much better than stock. I am new to these trucks so I might just not know any better though.

 

b24da5d298a19ce07e19f3d0a4af94ea.jpg

 

 

Sent from my iPhone using Tapatalk

Good to hear. Getting all 4 replaced tomorrow with stock 18's as well.

srgjigpog Enthusiast

srgjigpog

Posted
Posted (edited)

Just installed the 5100s on the front at the highest setting which gave me +2" at the front wheel wells. I was measuring 35.5" in the front and 39" in the rear before the install.

 

I was a little nervous about going to the highest setting because of a lot of the comments about the the ride being poor at that height. The ride is much better than stock. I am new to these trucks so I might just not know any better though.

 

b24da5d298a19ce07e19f3d0a4af94ea.jpg

 

Sent from my iPhone using Tapatalk

Any pictures of the rears installed?

Edited by srgjigpog
Barnes16 Enthusiast

Barnes16

Posted
Posted

Any pictures of the rears installed?

I only did the fronts right now.

 

 

Sent from my iPhone using Tapatalk

tootall87 Enthusiast

tootall87

Posted
Posted

 

Thanks for posting that. We do text during normal business hours! Or call us at that number. Or email us! Or Pm US, or Message us on facebook.

 

Got your text Corey, you ordered with Spencer which means your shocks should be shipping out today via Bilstein. Youll see them before the weekend.

 

Thanks!

 

Anybody home?? I've texted, emailed, called with no answer. I ordered on 5/7.

spencer52356 Enthusiast

spencer52356

Posted
Posted

Good Luck Tootall87, I placed my order on April 26th. I did receive the fronts finally but now I'm waiting on the rears. I did finally get ahold of Robert at MRT and he said he would call his rep @ Bilstien and get back to me but that was early last week and I have yet to get an answer. I called Bilstien myself yesterday and was told the rears are on backorder and 5 weeks out. Don't expect any communication because it's nonexistent. Sure would of been nice if there website could inform us that things are on back order when placing it in the cart.

  • Like 1
Bvonscott Enthusiast

Bvonscott

Posted
Posted

??? Man I ordered my rear 5100's from Amazon and got them in 2 days. And they even sent a replacement for one that was the wrong model for my truck and they sent a free replacement the next day. So I have an extra free shock lol. I got the 33-238319

tootall87 Enthusiast

tootall87

Posted
Posted

Good Luck Tootall87, I placed my order on April 26th. I did receive the fronts finally but now I'm waiting on the rears. I did finally get ahold of Robert at MRT and he said he would call his rep @ Bilstien and get back to me but that was early last week and I have yet to get an answer. I called Bilstien myself yesterday and was told the rears are on backorder and 5 weeks out. Don't expect any communication because it's nonexistent. Sure would of been nice if there website could inform us that things are on back order when placing it in the cart.

Got a call from him as well. Similar story, rears on backorder. Sending me the fronts now, rears when they get in. A simple email explaining that would cease all confusion and frustration.

Powerlines Enthusiast

Powerlines

Posted
Posted (edited)

Just had all 4 put on the truck and ended up with a 1.5" rake with the fronts being at the highest setting(was thinking it would be less). I also noticed the boots were installed up but I thought I read that a 2016 should go boot down? What difference if any does that make?

 

Before

4ad52f4634efbacd03e4ee2538ed3490.jpg

 

After

ae22968f5d36aa806ca668f37c94cc69.jpg

 

 

Rears

e7ec45e47a177e0c5a8990919c770f45.jpg

Edited by Powerlines
Barnes16 Enthusiast

Barnes16

Posted
Posted

Just had all 4 put on the truck and ended up with a 1.5" rake with the fronts being at the highest setting(was thinking it would be less). I also noticed the boots were installed up but I thought I read that a 2016 should go boot down? What difference if any does that make?

 

Before

4ad52f4634efbacd03e4ee2538ed3490.jpg

 

After

ae22968f5d36aa806ca668f37c94cc69.jpg

 

 

Rears

e7ec45e47a177e0c5a8990919c770f45.jpg

From what I have read, the Bilstein stickers should be right side up so they can be read which would be boot down. I don't know what kind of difference it makes though.

 

I also ended up with 1.5" of rake. Actually that is only the drivers side. My rear passenger side sits almost 1" lower than the driver for some reason; not sure what I am going to do about that or what is causing it yet.

 

 

Sent from my iPhone using Tapatalk

Powerlines Enthusiast

Powerlines

Posted
Posted

From what I have read, the Bilstein stickers should be right side up so they can be read which would be boot down. I don't know what kind of difference it makes though.

 

I also ended up with 1.5" of rake. Actually that is only the drivers side. My rear passenger side sits almost 1" lower than the driver for some reason; not sure what I am going to do about that or what is causing it yet.

 

 

Sent from my iPhone using Tapatalk

Thanks for the info. Got ahold of the shop and although he said it's doubtful they installed then upside down, they'll swap them around next week. Here's some info I found on the orientation

 

http://www.truckspring.com/blog/post/2014/05/28/can-i-mount-bilstein-shocks-upside-down

mookdoc6 Senior Enthusiast

mookdoc6

Posted
Posted

Count me in on the 5100's! I liked the shocks so much for the rear I bought the fronts almost immediately. After testing the OEM's the other day when I swapped out the passenger side shock was already sticking 3/4's on travel? Junk, most of you have already commented and the factory Shocks are straight JUNK!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • garagerog
      Navigating senior years.

      By garagerog · Posted

      First time it really happened to me was when I was 69 yrs old and I was called "Old Timer" by a complete stranger. Then in rapid succession came the aforementioned "Old Man" and my favorite of all "Pops".
    • newdude
      Where is the Ambient Air Temperature Sensor on a 2021 Chevy Suburban?

      By newdude · Posted

      Yea that's pretty normal to be off a few degrees.  Usually 2-4 degrees from say a weather app or thermometer.  
    • studly
      Where is the Ambient Air Temperature Sensor on a 2021 Chevy Suburban?

      By studly · Posted

      I just replaced the ambient air temperature sensor.  Easy as pie. I simply had to remove about 10-12 clips on the plastic cover over the radiator and remove two T-10 torx screws on the hood release lever to liberate the cover (Amazingly, none of the clips broke.  All came out and went back in with zero problems). Once the cover was removed, the temp sensor is easily accessible. The sensor cable snakes through a few guides and can be pulled out for even easier access to the sensor. I was able to work the sensor out of the mounting hole.  There is a red sliding catch on the plug that must be pulled back to disconnect the cable.  The plug was quite tight.  I had to use a screwdriver to pry it out. I plugged in the new sensor ($6.45 from RockAuto), snapped it into the mounting hole and re-snaked the cable. I put the radiator cover back on and reattached the lever arm to the hood release.  All done!     I started up my Suburban.  The temperature read 82 °F. Other thermometers at my house read 80 °F.  Close enough.  It might be reading high as my vehicle was sitting in the sun.
    • StingerZ16
      Navigating senior years.

      By StingerZ16 · Posted

      Remember when you were 50 and they called you Old Man?
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      That one looks decent for the price   BUT..I want something that also supports OBDI/1.5. A lot of the prosumer-grade scanners don't have legacy support in order to keep costs low. I believe the Autel does if you go higher end with them.   For fun, I reached out to a local Snap-On rep because I was interested in the 2600. $1895 MSRP, says he can do $1595. That's still a lot, but then again, that's not a horrible discount for just asking out of the blue. Could probably do better if I was a regular buying off his truck, but I'm not.   Not sure if I mentioned but I didn't realize with USED scanners from Snap On that you need to make sure a) the serial number isn't flagged as stolen. On the newer ones, SnapOn can remotely disable the device if it's flagged in their system. And, customer service can tell you if it is, if you're thinking about buying used. B) Make sure it's paid off. If the seller still owes money to the truck or if they financed through Snap On, the device can be remotely disabled until the balance is paid. It's less clear if SnapOn will tell you if a balance is still owed; I didn't make it that far with the used model I was considering. I did read that SnapOn has no way of tracking any "truck financing" deals between the SnapOn rep and buyer, only if they financed through corporate. So there's that extra caution needed.   Still waffling on whether I go with a ~$500ish Autel/TopDon or spend bigger money. The value seems to be in the prosumer brands. I'm not giving them enough credit TBH, actual production repair shops use them daily BUT I'm still allergic to certain kinds of underdog products trying to unseat American companies with solid reputations. SnapOn's scanner isn't wholly made in the US, but it is assembled here and they have US support and probably the most proven/ robust legacy support.   Something to think about. Value, or principles? There's a $1k difference.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...