Jump to content

Recommended Posts

Posted

Curious to know if any of you always keep your truck in 4wd auto. If so, does it hurt andything and does it effect MPG?

Posted

Anecdotal, but I had a 2015 that stayed in auto 4wd. It however was owned by my work so I wasn’t afraid to beat it up, and I didn’t track mileage at all. Never had any problems with the truck though.


Sent from my iPhone using Tapatalk

Posted

I think 4 auto keeps the transfer case in open diff mode, so it should be safe. However, if you're on dry pavement, not sure the value doing it. Mostly some mpg loss. If it was raining, I'd definitely use it.

Posted

4 AUTO engages the front axles but sends very little power to the front wheels until slip is detected. The power distribution is handled by an electronic clutch in the transfer case.

 

In auto, there is a slight fuel economy penalty and also more noise / vibration, both due to having the axles engaged and more rolling resistance.

 

Also, in theory, driving all the time in 4 AUTO would increase wear on the transfer case clutch and assorted components.

 

Although it is “safe” to use all the time, you really should be in 2WD unless the road conditions are sloppy. I usually use 4A if there’s been a snowfall in the last couple days and the roads and parking lots aren’t all the way cleaned up. I also have been known to slip it into 4A if I feel like the guy next to me wants to have a little stoplight race. Otherwise it’s 2H basically all the time.

  • Like 8
Posted

I read that it MPG drops by one if it's kept on Auto 4x4. Not bad for it but if you have unpredictable traction, better to keep it on.

Posted
6 minutes ago, Wiggums said:

 

I read that it MPG drops by one if it's kept on Auto 4x4

 

Says who?

Posted
10 minutes ago, Booger T said:

Says who?

Manual states slight drop in gas mileage if set on auto instead of rear wheel drive.

 

 

Screenshot_20190323_185143.jpg

  • Like 2
Posted

There is no good reason to do it... It will cause additional wear on the four wheel drive system.. Are you new to 4x4 trucks? If you have a locking rear end and you're not off road, there will be very few situations outside of snow that you use anything but 2 high... I will use AUTO if I am trying to get a jump on traffic off the line sometimes because the truck is quicker off the line with it but, beyond that unless there is significant snow on the road there aren't many reasons I can think of that any 4 wheel drive mode is needed if you're on paved roads..

  • Like 2
Posted
37 minutes ago, Imcrazy said:

There is no good reason to do it... It will cause additional wear on the four wheel drive system.. Are you new to 4x4 trucks? If you have a locking rear end and you're not off road, there will be very few situations outside of snow that you use anything but 2 high... I will use AUTO if I am trying to get a jump on traffic off the line sometimes because the truck is quicker off the line with it but, beyond that unless there is significant snow on the road there aren't many reasons I can think of that any 4 wheel drive mode is needed if you're on paved roads..

Agree.

:)

 

Posted

I've accidentally left my truck in auto the day after a snowstorm and didn't notice a difference in driving characteristics but like everyone else said, there's no benefit to it, only cons unless it's raining or snowing.

Posted
1 hour ago, Imcrazy said:

There is no good reason to do it... It will cause additional wear on the four wheel drive system.. Are you new to 4x4 trucks? If you have a locking rear end and you're not off road, there will be very few situations outside of snow that you use anything but 2 high... I will use AUTO if I am trying to get a jump on traffic off the line sometimes because the truck is quicker off the line with it but, beyond that unless there is significant snow on the road there aren't many reasons I can think of that any 4 wheel drive mode is needed if you're on paved roads..

Am I new to 4X4? That is a no. I’ve owned more than I can count. Btw, your rear end isn’t locked when you are in auto 4WD. It locks when it senses slipping. Will do the same thing in 2WD

Posted
3 hours ago, Aycock1987 said:

Am I new to 4X4? That is a no. I’ve owned more than I can count. Btw, your rear end isn’t locked when you are in auto 4WD. It locks when it senses slipping. Will do the same thing in 2WD

Yes I knew that about the G80 rear end... The auto mode is really only intended for mixed road conditions, IE partially snow covered roads and getting in and out of slushy parking lots or messy gravel roads. If you leave the truck in auto for a few days accidentally I'm sure you'll be just fine but, there is not really any reason to use auto unless you're off road or the road conditions are poor..

Posted

I agree with the folks who recommend running in 2H unless traction is bad. However, when I'm driving my company's trucks around the plant where I work, I find it will spin a little on the sand and gravel that's all over our roads so I usually shift to 4A so our safety guys don't give me shit. 

Posted (edited)
1 hour ago, Cpl_Punishment said:

I agree with the folks who recommend running in 2H unless traction is bad. However, when I'm driving my company's trucks around the plant where I work, I find it will spin a little on the sand and gravel that's all over our roads so I usually shift to 4A so our safety guys don't give me shit. 

Sand and gravel, yes ?

Clean pavement, no ?

Edited by UGADawgs
Posted
On 3/23/2019 at 7:52 PM, Aycock1987 said:

Curious to know if any of you always keep your truck in 4wd auto. If so, does it hurt andything and does it effect MPG?

I've always ran my trucks in 4wd auto.  No issues at all.  I've noticed that the gas mileage isnt really affected either based on my testing.

  • Like 4

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • The BORA 3/8" spacers arrived yesterday along with the extended lug nuts. I got the front wheels changed out today, but was overheated and covered in sweat so bad, I figured getting both front wheels done was a win, and took a cool shower. Hopefully, I'll go out tomorrow morning before it gets into the 80+ temps and do the backs. After getting the first wheel snugged up, I backed out one of the lug nuts then hand turned to count threads. I believe I stopped counting around 12-13, so I think I'm good there.    
    • My fullsize truck is averaging over 26mpg so I'm pretty happy with the increased fuel economy targets. When I had my gas Silverado (2020 5.3) it was averaging 21. Again, for a fullsize truck, that's very different from the 12-15 these things used to get 30 years ago.   Whine all you want, increased MPG is a good thing.
    • That is a fair point, and I think an OBD-first proof is probably the right next step. I agree that the value is not the hardware box by itself. The marketable part would be the software: always-on capture, baseline learning, event reduction, system-specific reports, and alerts. Also agreed that if an OBD device is always plugged in and has local storage, it should not miss the event in the same way that a scanner plugged in after the fact would. The only thing I would not want to assume yet is that an ELM327-class device gives all the late-GM data needed at the rate needed. Standard OBD live data, DTCs, freeze frame, Mode 6, VIN, and calibration information are definitely the right starting point. GDS2 also proves that a lot of useful ECM data can be viewed through the DLC without needing a DTC first. The question I need to test is whether the data needed for a useful GM V8 event report is actually available through the DLC, and at a useful sample rate: - misfire counts / roughness by cylinder - AFM/DFM state - oil pressure and oil temperature - fuel trims - voltage / reset context - U-codes and communication events - calibration / software information - whether these are standard PIDs, enhanced DIDs, Mode 6 data, GDS2-only data, or not available So I think the right benchmark is: 1. Build the OBD-only version first. 2. Keep it plugged in and logging locally. 3. Compare it against GDS2 / freeze frame / HP Tuners or another higher-end logger. 4. Measure which parameters are available and at what update rate. 5. Only justify ECM-side hardware if it captures useful evidence the OBD version cannot. So you may be right: the consumer product might simply be an always-plugged-in OBD event recorder with much better reporting. A question for you: when you say ELM327 devices can already deliver all the data needed, do you mean generic OBD Mode 01 data only, or GM enhanced data as well? For a useful GM V8 report, would generic OBD data be enough, or would you expect the tool to include enhanced items like misfire by cylinder, AFM/DFM state, oil pressure/oil temp, U-codes, and calibration information?
    • 87 down as low as $5.14 here... winning!
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...