Jump to content

Recommended Posts

Posted

The check engine light just came on in my new GMC with just over 2k miles on it. I just towed for the first time yesterday, but not a heavy load (definitely under 3000 lbs). I pulled the codes just now and got:

 

U0101 Lost Communication with TCM

U0129 Lost Communication with Brake System Control Module

 

I'm probably going to have to take it in to the dealer, but first wanted to see if this is a common issue or if there are any relevant bulletins or recalls out first, just so I can go in well-informed.

 

Thanks.

Posted
PIT5664A MAY be related .Fix is to reprogram ECM.
Posted
4 minutes ago, tbarn said:
PIT5664A MAY be related .Fix is to reprogram ECM.

Thanks. That looks like a likely candidate. Does anyone have a copy of the full document?

Posted
14 hours ago, relevante said:

Thanks. That looks like a likely candidate. Does anyone have a copy of the full document?

I just signed up for a 1 day repairprocedures.com subscription. It's $15, but they have a pretty awesome archive of info, including what appears to be a full service manual.

 

Anyway, the details on this seem to be that the system sees the battery voltage dropping while parked, which makes sense because I just added a BlackVue dashcam system with park mode that's drawing power while the truck is off, as long as the battery doesn't get too low. When the system sees a low voltage, it tries to wake up some other modules to do various things. But in earlier versions of the software, the codes that it sends to wake up those other modules may not be correct. There's an updated software that became available on 3/18/19. My truck was built about a week before that.

  • Like 1
  • Thanks 1
  • 3 months later...
Posted

relevante

did they get your truck fixed from the u0101 and u0129 codes that it was showing! what was the problem if you don't mind me asking, mine throw the same codes this evening.

Posted
On 5/6/2019 at 4:17 PM, relevante said:

The check engine light just came on in my new GMC with just over 2k miles on it. I just towed for the first time yesterday, but not a heavy load (definitely under 3000 lbs). I pulled the codes just now and got:

 

U0101 Lost Communication with TCM

U0129 Lost Communication with Brake System Control Module

 

I'm probably going to have to take it in to the dealer, but first wanted to see if this is a common issue or if there are any relevant bulletins or recalls out first, just so I can go in well-informed.

 

Thanks.

Hey partner, I get those codes everytime I remote start my truck with it hooked up to the trailer. Considering it a glitch.

  • 2 weeks later...
Posted (edited)

I too received codes U0101 and U0129 when pulling my empty toy hauler, about 6,000 pounds.  The code went away after detaching the toy hauler.  I have an appointment to take it to the shop for the software update.  It was new in March, so under warranty.

Edited by Sheck
fixed typo
  • 5 months later...
Posted (edited)

I've been seeing these codes show up on my Bluedriver OBD II code reader even after today's most recent recall that refreshed the EBCM.

 

If anyone has a fix for this I would appreciate the info - dealer is clueless in the matter.

 

 

Here is the summary:

Quote

Make: Chevrolet Year: 2019

Odometer: 2,140 miles

----Electronic Brake Control Module Codes Scan Report---- 6 Electronic Brake Control Module Trouble Codes:
1. U0140
Lost Communication With Body Control Module

2. U0100
Lost Communication With ECM/PCM "A"

3. U0101
Lost Communication with TCM

4. U0131
Lost Communication With Power Steering Control Module

5. U0151
Lost Communication With Restraints Control Module

6. U0146
Lost Communication With Gateway "A"


****Update

well, dealer said codes were history codes. Flashed ECM and reflashed EBCM for second time under latest recall. Performed a “complete history wipe” whatever that means - not sure how that is different from clearing codes. But I had to go back this morning for a B1517 as they left some connections loose. 
 

Now I have driven 60 miles (since this morning) and 0 codes and transmission feels very smooth. Fingers crossed. 

 

Edited by splatmatt
Posted

I had the MIL on. U0100, U0101, U0146 and P25A2. The light went out before I could get an appointment with the dealer and didn't feel like driving all that way to hear the "well we don't see anything wrong" BS and then I saw the recall for the brake module and wonder if they are related. I will try to get it in soon. Keep us posted.

Posted

Im getting U0100, U0101, and U0146 after hooking up my trailer today.  Issue is not going away after removal of the trailer.  I removed the neg battery cable for a extended period of time,  code still shows.      Cant clear it using my obd scanner either.   

 

Good to know its most likely a false alarm.   Ill take to the dealer later in the week. 

Posted (edited)

Well it has been around 500 miles since EBCM firmware was applied and the dealer performed a history wipe. 
 

One thing I noticed is MPG is about 1.5mpg better and the voltmeter on the dash is always riding above ~14.4V. After the update it now seems to behave more typical to the GM regulated voltage control system and zero codes including all of the modules. 

 

 

**** issues are back again... dammit

 

 

Edited by splatmatt
Posted
On 2/13/2020 at 3:35 PM, brianf60 said:

I had the MIL on. U0100, U0101, U0146 and P25A2. The light went out before I could get an appointment with the dealer and didn't feel like driving all that way to hear the "well we don't see anything wrong" BS and then I saw the recall for the brake module and wonder if they are related. I will try to get it in soon. Keep us posted.

Have you went and seen the dealer? Just had all four of these yesterday and the light was also gone after next day. Are you having any braking issues ?

Posted

I haven't been able to get it to the dealer yet. I'm not experiencing any noticeable issues with my brake. If I had I would just get it towed.. The MIL has not come back on in over the week either.

Posted

Im going to add,   mine cleared its self after 24 hours.  (OBD Scanner would not clear it) 

Posted

Has anyone found a resolution to this yet?
 

i think I have two different issues.  The u101 and u100 and u101 and P25a2 issue.  Had this twice. First time was to far from a dealer.  Second time it was Sunday and the dealership was closed.

 

yesterday I had just p25a2 code only (none of the original ucodes) which might be the brake module; a software release was released for this in December.  But it had bugs and caused problems with power steering.  Now a second software update was released about a week ago.  

https://www.autoblog.com/2020/02/11/gm-brake-software-recall-silverado-sierra-ct6/

 

these show different symptoms and with a high probability are different issues.  Did anyone get any real/solid/effective or practical information out of GM on the ucode issues.  There are about 4 different threads out there so probably hundreds of people have had this.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • When I had a Bumper subscription for a few days when I needed to run title histories on cars I was looking at, I decided to look up a few of my old/past vehicles.   My 2015 Silverado was still actively registered and it last sold in 2024 with 160k on the clock. No idea if that's on the original engine but someone's keeping it on the road or the original AFM stuff is still going.   It used 0w20. I remember feeding it Mobil 0w20 AFE for the first 30k of its life on <5k OCI's.     Edit: Just did a nationwide search on Autotrader for 2015-2025 Silverados with 5.3's and sorted by highest mileage first.   357k 352k 292k 291k 290k 277k 271k 268k 266k 259k 256k   High mileage on a modern 5.3 doesn't seem all that uncommon, but that's just searching mostly dealer ads on Autotrader. FB Marketplace has all kinds of high mileage 5.3's going back to 2007    
    • I can't say I have ever heard of someone getting that type of mileage out of a set of tires even though they rotated on a regular basis but without a doubt if the front end gets wear and those tires are no longer able to track straight it scrubs them off, and driving style and road surface make a huge difference as well.    However that is not what prompted me to comment as it was the new tire theme of sitting in storage waiting to be used scenario. I am sure some tires can last for quite a while in storage if its not too warm and out of the sunlight but unfortunately some tires the way they their rubber compound is formulated they can age and dry out even in a reasonably decent storage location. My brother ran into this maybe three years ago when he was looking at the tires that were on his dually truck and a combination of wear on the rear ones and noticing that the front tires had some cracks around the sidewall of the tire not far from the bead but he had replaced only the front ones not long ago with 2 of the remaining 6 he had left from the initial two sets of takeoffs he had all bought at the same time .... 10 years ago ! ( the years fly by, a truck that only gets used a bit to haul a camper during the summer and sits in a shed for a large part of the year ). That second set of 6 tires, two he had put on the front prior like I said and they had very little wear but those cracks were now present. So we go into the shed where the other 4 tires had been stored all this time and every one of them had the same cracks in the sidewalls and so in the end it amounted to throwing away 6 brand new but 10 year old takeoff tires into the dump that he got a deal on at a tire shop because they aged out. They were a Ford factory equipment BFG tire and those tires did not age well compared to some tires I've seen far older then that and did not show that type of aging. True, they always say up here anyway that 7 years is sort of a limit for age by rights, we don't have the intense prolonged heat that many of you have down in the states that just cook tires and depends on where the vehicle sits when not in use. GB, another words maybe had you bought a set of tires to store it would have been fine as long as you used them up fast enough but there are no guarantees when it comes to rubber, tires or of that other type stored in some guys wallets 😆
    • 2020 2500 HD...I had some trouble getting the key into the ignition switch but went in fine after applying some extra effort. Since then, the door chimes when open when the key is out of the ignition. Also, when I lock the doors with the switch on the arm rest, the driver door locks but then unlocks. (I can lock everything fine with the fob) The message on the little screen displays the "Engine Hours"...kinda weird.   I'm guessing something happened to the ignition switch and it thinks the key is still in there. I unplugged the batteries for 20 minutes, no change. There are a number of videos on YouTube but nothing I can find that address this specific issue. Ideas appreciated, thank you.
    • Based on what I can tell, yes.   As for updating it, its a mixed bag.  Updates do fix a lot of issues, but occasionally can create some oddities.  They do more good than harm though overall.     Here's what the most current one does and a  V171 Improvements Important: Improvements will vary by model, build configuration, system, and sales region. Not all vehicles have all features. OnStar and Wi-Fi may not work after remote start CarPlay may not automatically reconnect Part of the Driver Attention messaging screen may be in English even though the language is set to something else XM may not work After a dead 12V the radio may set to Arabic at each startup Bluetooth contacts might not be able to sync with the vehicle During an OTA the 12V battery may drain Customer might see a screen telling them to return to the dealer After changing the Wi-Fi SSID or password a device may not disconnect If a device is connected on the 2.4Ghz band, nothing will connect to the 5Ghz one, which could show as slow Wi-Fi speeds Customers might have noticed Wi-Fi dropping in certain areas and reconnecting later Customer might see the top of the screen blinking during Android Auto Android Auto may not connect CarPlay audio might momentarily cut out The "Add Phone" button may be grayed out The radio may not start up   V167 Most Notable Improvements:   Outside Air Temperature is incorrect. -You may see a popup message for Engine Shift. (Corvette Only) After changing the exhaust sound they get a popup that "mode change not applied", even though it was. -When changing volume, the volume bar is for Traffic instead of Audio. -(Corvette Only) Improvements to the placement of buttons and text. -If the customer receives the message "Apple CarPlay Could not connect", the cursor might move in the opposite direction than expected when using the control knob. -Android Auto automatically starts playing their music, even though they have turned that off in settings. -Intermittently they have a red OnStar LED with no OnStar function and/or no audio. -The minimum length of the Wi-Fi password was increased to 12 characters. -The popup message "Driver Attention Check, check your mirrors or Super Cruise will shut down" may not have come up on the display when it should have. -Startup animation added for 20th anniversary of the V-Series on Cadillacs. -The Navigation app received location improvements when going under long underpasses. -In the Navigation app there are filters for charging points that the vehicle cannot use.   V164 Most Notable Improvements Most notable improvements contained in this release may include: Apps Intermittently, an “SD Card Removed” message will pop up in the Navigation app. While in the audio app, the radio may stop working. Trailer Tire Pressure sensors may not be learned in the Trailer app. Not being able to return to the home screen while in the Camera app. After an ignition cycle, the radio might go to a black screen or stop working if using Sirius XM. Spotify icon truncated on Audio app.   SXM When changing power modes with the ignition switch, the HVAC pop up might appear. During startup, the radio will show the brand splash screen then go blank. Receiving a confirmation pop-up when changing drive modes. A “Return to Dealer” message may appear on the radio screen. SuperCruise setting toggle may not work. System After an ignition cycle, the radio might go black or stop working if using Sirius XM (SXM). Settings When performing a factory reset, the radio may stop working. After performing a factory reset, the radio may stop working when trying to switch users. When trying to go into the Language section quickly after startup, the radio may stop working. Projection Wireless CarPlay cannot be connected after unpairing another wireless Android Auto device. When the Android Auto screen comes up to connect wirelessly, the screen may freeze if the Cancel button is pressed. Removed the Apple CarPlay Cannot Connect screen when a device fails to pair during the autoconnect process. CarPlay information may not show up in the audio app. Near Field Communications (NFC) chime may be heard when NFC does not work. The Cannot Connect screen does not pop up after the first connection on wireless CarPlay fails. Apple CarPlay is now functional in Guam. Over the Air (OTA) When a software update is cancelled, the downloading logo may still be displayed. Energy When using the Energy app, the radio may stop working. When plugging in the vehicle, the display might show “Now” instead of “Charging Upon Plug In.” Instrument Cluster Voice recognition can be started while on an OnStar or phone call. When downloading contacts, there is a progress bar and circles on the Recents page of the cluster. The temperature on the cluster and the display may be different. After receiving and ending a call on the secondary paired phone, the cluster may get stuck on the phone menu. Bluetooth Intermittent Bluetooth connection loss.
    • Looking for help troubleshooting a metallic like front end rattle. Figured I’d see if anyone had thoughts before I schedule an appointment with the dealer.   The rattle is fairly loud and occurs primarily when the front driver side wheel hits a bump, even fairly minor road seams. Sometimes does it when the passenger hits a bump but I don’t believe when the rear hits. Rattle still occurs when foot is pressing brake peddle so I think that rules out the caliper rattle I’ve read about. I’ve also checked the running boards and they are tight.   Most noticeable at slow speeds.    Any insight is appreciated. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...