Jump to content

2015 Sierra, 6-speed transmission clunk

RahinMVA

By RahinMVA
in Troubleshooting & Recalls

 Share

Recommended Posts

RahinMVA Enthusiast

RahinMVA

Posted
Posted (edited)

Hi all,

 

I have a 2015 GMC Sierra, 51K miles, and my transmission acts funny: 

 - rough shift from 2 to 3 when starting from a dead stop

 - occasional "clunk" when decelerating from highway speed (foot off the accelerator)

 - when in stop-and-go traffic there is strange / clunky shifting between gears, occasional random "clunks", almost like it can't figure out what gear it wants to be in

 

Any thoughts on these issues? Could it be related to the AFM / DoD? Could my transmission be going bad already with just 51K miles? Thoughts on how to correct this?

 

Any input would be appreciated. Thanks!

 

Rich

Edited by RahinMVA
Lsgun1 Enthusiast

Lsgun1

Posted
Posted

Sounds like pretty normal operation. The AFM definitely seems to change how they shift even though it's not supposed to. Have you checked the fluid level and condition? You are at the miles it should be changed.

RahinMVA Enthusiast

RahinMVA

Posted
  • Author
Posted
3 hours ago, Lsgun1 said:

 Have you checked the fluid level and condition? You are at the miles it should be changed.

Yes, I had the fluid & filter changed at about 48K, per the owners' manual recommendation. Symptoms were the same before and after the fluid change.

 

It is hard to hear that this might be "normal." My only other experience is my old truck - a 2000 Silverado that had 185K miles on it when I bought it. Other than the typical clunk when shifting out of Park, it was very smooth.

14TopazZ71 Enthusiast

14TopazZ71

Posted
Posted

Can you pop your air filter box open and see if there is oil in the airbox? Mine had the same transmission issues, the MAF was coated in oil. 

RahinMVA Enthusiast

RahinMVA

Posted
  • Author
Posted (edited)
54 minutes ago, Grumpy Bear said:

Is this something it just started doing or has it been like this from day one?

No, not at all from day 1; but it also wasn't anything sudden. It was a subtle ramp up over maybe the last 18 months or so to the point that I now notice the rough shift from 2 to 3 all the time; and the odd clunks described in my original post are now obvious.

 

49 minutes ago, 14TopazZ71 said:

Can you pop your air filter box open and see if there is oil in the airbox? Mine had the same transmission issues, the MAF was coated in oil. 

Just looked. No sign of oil.

 

 

Also, FWIW, this truck has only been serviced at GM dealers.

Edited by RahinMVA
BlancoSilverado Enthusiast

BlancoSilverado

Posted
Posted
1 hour ago, 14TopazZ71 said:

Can you pop your air filter box open and see if there is oil in the airbox? Mine had the same transmission issues, the MAF was coated in oil. 

14Topaz has a good point. you might want to buy a $5 spray bottle of MAP senor cleaner and see what it does. 

Grumpy Bear Senior Enthusiast

Grumpy Bear

Posted
Posted
1 hour ago, RahinMVA said:

No, not at all from day 1; but it also wasn't anything sudden. It was a subtle ramp up over maybe the last 18 months or so to the point that I now notice the rough shift from 2 to 3 all the time; and the odd clunks described in my original post are now obvious.

 

Just looked. No sign of oil.

 

 

Also, FWIW, this truck has only been serviced at GM dealers.

Clunk is sound that 'loose' devices make. It's slack take up. As a device wears clearance increases and noise/feel happens. While it may sound odd for this to happen at such low miles it may have started during manufacture that parts were at the top of their specs. Some things easy or at least cheaper to check. Differential back lash. There is a maximum spec for this. A GM dealer can measure this. Front driveshaft yoke splines need heavy grease. Universal joint wear. Just some ideas to add to cleaning the MAP. Let's not worry about the big things until the little ones have been looked at. :) 

  • Like 3
flyingfool Senior Enthusiast

flyingfool

Posted
Posted (edited)

check this out, no.1 reason to delete the trans t-stat..  minimize heat distortion to the plastics in the valve system

 

Edited by flyingfool
  • Like 1
Malibu SS Enthusiast

Malibu SS

Posted
Posted

Buy a tuner.  Delete the Active Fuel Management....Raise the shift points by about 300 RPM.......and increase the shift firmness by 25%  That should fix ya' right up....

  • 2 weeks later...
Og Goldie Enthusiast

Og Goldie

Posted
Posted

yea im having the same clunkness but only at start form a complete stop like at a stop light. Dealer regreased driveshaft plines then it stopped, but after installed a 2.25" front leveling kit the clunk was back. i now have an diablo 87octane tune, afm off, trans point at 15% & still doing it. so at this point im completely convinced chevy dropped the ball with the drivetrain issues

lmcdonald10 Enthusiast

lmcdonald10

Posted
Posted
On 5/17/2020 at 8:42 PM, RahinMVA said:

Hi all,

 

I have a 2015 GMC Sierra, 51K miles, and my transmission acts funny: 

 - rough shift from 2 to 3 when starting from a dead stop

 - occasional "clunk" when decelerating from highway speed (foot off the accelerator)

 - when in stop-and-go traffic there is strange / clunky shifting between gears, occasional random "clunks", almost like it can't figure out what gear it wants to be in

 

Any thoughts on these issues? Could it be related to the AFM / DoD? Could my transmission be going bad already with just 51K miles? Thoughts on how to correct this?

 

Any input would be appreciated. Thanks!

 

Rich

It is not normal. My 2017 Silverado with 6 speed does the same thing. I just had the transmission rebuilt and it’s doing the same thing. I’m thinking maybe TCM issues? I don’t know but I’m to the point of selling my truck over this 

  • 1 year later...
Podcastville New Member

Podcastville

Posted
Posted

This was happening to my 2015 gmc sierra. The occasional clunk turned into more frequent clunks, especially when under load at low rpms. Turns out I need a new transmission at 51k miles. Well that's what the dealership says atleast.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Buckwild27
      Gas Prices

      By Buckwild27 · Posted

      I agree. 
    • Atlas
      Gas Prices

      By Atlas · Posted

      87 down as low as $5.14 here... winning!
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Progress... sort of.   Intake is disassembled, spider is out, fuel lines removed. Used a torch on the stripped screw with the lower intake off, much easier when I've got the intake sitting on my workbench, I made it talk. Walked right out with a pair of vice grips once it was nice and toasty hot.   New parts are piling up on my service cart waiting to be installed. Distributor, temperature sensor, new gaskets, fuel line kit, themostat, water neck.   My new pickle is I don't want to spend $600 on a replacement spider. I'm not sure IT is bad. I'm probably splitting hairs. Or it's $300 to send mine away and another 3 weeks of the truck just sitting. I have half a mind to assemble everything with the old spider to see if I can get away with just replacing the fuel pressure regulator to be safe. The obvious issue was the gushing high pressure fuel line which will be replaced. Getting to the spider really isn't that hard, and now I know what I'm doing , swapping it would be a breeze should it absolutely need one. Stupid, or smart?   The part that gives me pause is replacing the distributor. Well, it's already out. And I didn't mark it, whoopsie! Engine was at TDC when I removed it, I know that, so upon correct reinstall the metal tip on the rotor should point to the TDC mark on the distributor because that's where it was pointing on the old distributor. Worst case I'm a tooth off and have to re-stab it.   But then, what? I assume the truck will start. It doesn't appear the timing can be set. Here's the problem: These distributors can't be rotated but a degree or two, by design. What I read is Cam ****** needs to be -2 to +2 degrees, ideally at 0 (and checked/set above 1000 rpm). There should be enough wiggle to get that properly set, but checking the reported value is another potential issue. My Actron 9185 scanner says it supports enhanced GM PIDs and Cam ****** is one of them but it's unclear that I'll be able to correctly see it over OBD 1.5. I can see why people end up junking these things with life left in them. They're an absolute nightmare with tweener-year diagnostics/electronics and unobtanium parts.   Fingers crossed it starts and idles nicely. There can be hope, right? I'ma buy a lottery ticket the same day just in case.   Next steps..DO IT. I have not installed an intake before so I've been reading and watching a lot. Some say NO RTV except on china walls, some say DO RTV on water ports but not fuel/air intake. 1/4 or 3/8 bead on China walls? I think my strategy will be, obviously, RTV china walls with overlap on the gasket corners. Chapstick-style RTV the water ports. Leave intake ports dry. The only set of intake gaskets I could find locally are Edelbrock performance gaskets (uh...for an asthmatic 190hp V6? LOL) so we'll see how they do.   #NoToolLeftBehind. It took an hour, but my recovery mission for my deep 10mm socket was successful. It had rolled down the bellhousing and wedged itself between what I think are the fuel lines? I couldn't see it at all, but with a junk antenna I had laying around, I blindly went poking/sweeping for it, heard it clink, raised the truck, and caught a sliver glimpse of chrome with a flashlight way up there in Narnia. I had pushed it farther along the lines holding it captive, but within access of severely improvised tools, poking and cursing at it to finally knock it free to where I could get a fingertip on it to bring it home.    Not much to see.      
    • RyanbabZ71
      Gas Prices

      By RyanbabZ71 · Posted

      Thats crazy considering im right next door (Indiana)
    • Black02Silverado
      New Retail & Commercial Promo

      By Black02Silverado · Posted

      For a limited time, retail and commercial accounts receive an AMSOIL Vinyl Tool Tray with their order of $500 or more when they use code TRAY726 at checkout. The promotion runs through July 21, 2026.   Order at https://syntheticadvantage.com   Want to use AMSOIL in your business or sell at your store, apply here.  https://www.amsoil.com/business-opportunities/?zo=521390  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...