Jump to content

Is your GMT-900 using oil  

1,555 members have voted

You do not have permission to vote in this poll, or see the poll results. Please sign in or register to vote in this poll.

Recommended Posts

Posted

Thanks !!!

I missed that in the manual.

I was checking it cold. :happysad:

  • 4 weeks later...
Posted

2007 Sierra Z71 AFM 5.3 129K miles mostly highway to and from the jobsites. 2 oil changes ago I ran a quart of Lucas Oil with 5 quarts of Pennzoil 5w30 and the last oil change it seemed to have used less. Some mornings I hear some piston slap on startup but it goes away pretty quick. oil pressure is still solid.

Posted

09 ccsb, 5.3l with VIN code M. i believe this is the Al block. using ~1 quart in 5000miles. went through the pvc breather/ valve cover/ fouled plugs routine at about 40k. Blackbear tune at about that same same, including disabling the afm. oil consumption improved slightly but remains at ~.75 quart per 5k. no formal oil consumption test but am planning to do one. using mobil 1 syn and lucas oil syn oil stabilizer. 65k miles on the truck currently.

  • 1 month later...
  • 2 months later...
Posted

2011 5.3 CC here just crossed 54k miles. No oil usage to date, BUT...

 

Last month truck had thick blue smoke out of the tailpipe on warm start. Twice in two days, and hasn't done it since. Oil level is fine.

 

Noticed that anytime its in V4 I'm getting serious detonation - that at any load, it will kick it back to V8 almost instantly. Also has started idling rough.

 

Going to get the Range device, but in the meantime, 5/100k warranty just expired and I want to ask the dealer to do a top engine clean and investigate? Any suggestions?

Posted

 

 

Last month truck had thick blue smoke out of the tailpipe on warm start. Twice in two days, and hasn't done it since. Oil level is fine.

 

Last month truck had thick blue smoke out of the tailpipe on warm start. Twice in two days, and hasn't done it since. Oil level is fine.

 

Thick puffs of smoke on startup is when my problems started.

Get that Range device to keep your engine in 8-cylinder mode.

  • Like 1
Posted

....

 

Going to get the Range device, but in the meantime, 5/100k warranty just expired and I want to ask the dealer to do a top engine clean and investigate? Any suggestions?

 

Range works great - I've got one in mine.

 

As for the dealership, I'd advise against that. Your warranty expired - no need to go there. The prices are high, and I have yet to see a dealership with top-notch workmanship. Everything is rushed, and billed at top dollar. Find a reputable local garage and go there. You'll thank me later.

  • Like 2
Posted

If you want to run an additive, I'd recommend this. https://www.bgprod.com/catalog/engine/bg-epr-engine-performance-restoration/ I don't usually like running additives, however- BG has been around a long time and seems to have a good track record. I ran BG44K in some older fuel injection vehicles at the recommendation of my auto repair facility, and I was satisfied with the results.

  • Like 1
Posted

Same stuff the dealer uses to do the decarboning procedure on the GDI engines. Stuff actually works, unlike autoparts store crap.

Posted

2011 5.3 CC here just crossed 54k miles. No oil usage to date, BUT...

 

Last month truck had thick blue smoke out of the tailpipe on warm start. Twice in two days, and hasn't done it since. Oil level is fine.

 

Noticed that anytime its in V4 I'm getting serious detonation - that at any load, it will kick it back to V8 almost instantly. Also has started idling rough.

 

Going to get the Range device, but in the meantime, 5/100k warranty just expired and I want to ask the dealer to do a top engine clean and investigate? Any suggestions?

 

Smoke on start up on my 09 Tahoe at 50,000 miles is where my troubles began. I believe the dealer cleaned the engine out per GM instruction. A couple of months later at startup I had no oil pressure. The dealer said it was a spun bearing and they replaced the engine under warranty. I think it had to do with AFM myself.

  • Like 1
  • 1 month later...
Posted

Put in a bottle of motor medic and drove it about 70 miles then changed the oil. (I did this a couple of times ) I quit using Mobil 1 and switched to the cheap Walmart brand. I rarely smokes now and burning cut in half. Not sure why. Maybe somebody here has a theory?

Posted (edited)

I had oil eating issue with a 2006 Cadillac CTS 3.6 I got a year ago with about 52K miles on it. Did a few 1000 mile oil changes, using Amsoil Engine Flush at each change and ditched the M1 5w30 recommended by GM and started using Pennzoil 10w30 conventional (it has the GM 6094 rating recommended in the manual). Oil consumption dramatically decreased and engine runs better than ever. Even will bust the EPA highway mpg rating occasionally.

Edited by Cowpie
  • Like 2
Posted

I had oil eating issue with a 2006 Cadillac CTS 3.6 I got a year ago with about 52K miles on it. Did a few 1000 mile oil changes, using Amsoil Engine Flush at each change and ditched the M1 5w30 recommended by GM and started using Pennzoil 10w30 conventional (it has the GM 6094 rating recommended in the manual). Oil consumption dramatically decreased and engine runs better than ever. Even will bust the EPA highway mpg rating occasionally.

Exactly! I believe the smoke at start up and the oil burning are related to sludge buildup and the use of synthetic oils (Mobil 1 in my case and yours apparently).

 

Those with smoking 5.3's should try flushing and a few short term oil changes then switch to conventional oil. That seems to help tremendously. Not sure why unless it frees up the stuck rings thus reducing blow by?

Posted (edited)

I chose the Pennzoil 10w30 conventional because of its reputation for cleaning up engine internals and the fact that the Petroeum Quality Institue of America tested it and found it had an exceptional additive package and even out did many full synthetics in NOACK performance. And at around $15 for a 5qt jug at my local farm and home store, a good value.

Edited by Cowpie
  • Like 1
  • Thanks 1
  • 2 weeks later...
Posted

From what I understand, the oil consumption issues are due to the rings seize on the AFM cylinders because of lack of maintenance and the conventional oil not holding up over time. GM switched to the Dexos full synthetic, lower viscosity and 8 qt + capacity to minimize the problems that the gen 4 5.3 had. My wife's '07 had the slugs replaced about 15k before we bought it. I run Valoline full synthetic and change the oil every 4500 to 5000 with no issues. I did disable the AFM.

 

There is a TSB on the driver's side valve cover allowing oil to get sacked into the Pcv vacuum line. Ours smoked up the garage on cold startup before we changed it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Disassembly may be Required!   Every blender makes claims but do  you ponder those claims? What was really said? Was it true?  Motive for saying it? What does in infer?  Is that inference true?    Let's do one.    Claim: Made from shear stable base oils.    What was said: Base Oils are shear proof.   Was it true: Yes.  ALL base oils are Newtonian.    Motive / Inference: To imply the fully formulated product is Shear Proof.    Is the Inference true?: Most fully formulated multigrade oils contain Viscosity Modifiers or VM's, sometimes called VII or Viscosity Index Improvers. There are four types. One is in fact shear proof but it also has a bad effect on extreme cold flow and is restricted to use in specialty oils. A second has limited shear called a 0-5 SSI polymer. Meaning its shear is limited to a range of zero to five percent as reported by the ASTM D6278 Shear Stability Index test. A few high end oils, like Torco SR-5, use them and brag about it profusely. Actually all that use it point it out. The last two shear dramatically and are often marketed as a 'feature' of the product aiding the oil to meet fuel standard requirements of ever stricter rules. One shears more than 5% and the other up to 20%. As you make guess, cost is directly linked to shear down and as such the majority of oils use the cheapest organic polymers sold to make grade and pass stringent tests.    PPD's or Pour Point Depressants also shear a bit, only a few percent and hide inside the 0-5 SSI capabilities.    The blender knows he can not out engineer Stribeck. Physics is not a suggestion. But he can wordcraft the unsuspecting toward believing a false claims INFERENCE. This is LEGAL. It is COMMON, and it is EFFECTIVE.         
    • I don't recall ever dealing with one on an '06 and back. It may not even exist on that. I can't remember for sure.   Any kind of ice in or after the evaporator is normally due to low charge with both a clutch-cycling orifice tube system, and a TXV system.
    • Engines wear. It is unavoidable. So the question isn't if it will wear out but rather WHEN it will wear out. That question is about rate and RATE is a HUGE problem for almost everyone; but not in the way we may think.    Unless there is something drastically wrong with your powertrain, wear is exceedingly slow. It doesn't wear out in minutes or hours or days or months but in years or even decades. Ditto sludge and varnish. Humans are an impatient lot so to see the benefit of a truly superior product you may have to wait a very long time. Most will get bored first and trade before they reap the benefit.   Humans are not companionate creatures when it comes to those we do not know. We don't care what happens to the second or third owner as long as it doesn't happen to us or someone we know and actually like.   Sad commentary on humans but it is what it is. That thus, then, there is no advantage...to or for you if the above paragraphs adequately describe you.    BUT if you are a buy and hold type and patient enough to reap the rewards of your labors then that thing that is happening that you haven't yet seen, but will; can be abated by such products. Seals harden and leak with time and lots of it. Rings stick after thousands of miles of a slowly building plaque of varnish.    Then there is this. This didn't happen over night and this poor fellow knew when he removed the cover and not one second before.   Not "aware' isn't the same thing as "isn't happening".        The above was typical of the Ford 361 and 391 bus motors on Bulk Pennzoil Mineral Oil products on 3K mile OCI's at about 60K miles back in the 60's and 70's at the Anamosa School District when my Uncle took over their maintenance program.    This is Pepper at @ 165K on 5K OCI's using Group IV/V Full Synthetics.      HM oils will help the first but not the second.    Then again if one used..... ah, ya know.....
    • Thanks for coming back with an update. 
    • Awesome you got it sorted! That's a new potential issue I'll have to mark in my book of issues. Thanks for the feedback.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...