Jump to content

Recommended Posts

Posted
3 hours ago, Vblock said:

Not sure if this is the correct place to post or not but I’ve read through a lot of this thread and haven’t seen anything related to my question. For you guys running 35 in tires what engine and gears do you have? I have 33’s but really want 35’s I just don’t wanna put too much stress on the tranny. I have a 2017 Silverado LT Z71 5.3 with 3.42 gears. Will 35’s be too much? 

I have a 2015 Silverado, same engine and gears. 
The difference in town wasn’t noticeable with the 35” tires and 6” lift. On the the interstate tranny downshifts more for slight grades. The big difference was losing 5mpg . But I knew this going in so not a surprise. The folks with 3:08 gears say they notice a loss of get up a go. I believe you’ll be fine as most of us are. In the future I got plans to re gear to a 4:10 . From what I read and my local shops recommendations that should put less stain on the Powertrain and give back some of the performance. Hope this helps 

Posted
8 hours ago, Hutch72 said:

I have a 2015 Silverado, same engine and gears. 
The difference in town wasn’t noticeable with the 35” tires and 6” lift. On the the interstate tranny downshifts more for slight grades. The big difference was losing 5mpg . But I knew this going in so not a surprise. The folks with 3:08 gears say they notice a loss of get up a go. I believe you’ll be fine as most of us are. In the future I got plans to re gear to a 4:10 . From what I read and my local shops recommendations that should put less stain on the Powertrain and give back some of the performance. Hope this helps 

Yes it does! Do you have a tune? I know it’s not a permanent solution to the bigger tires and the tranny but I have a custom tune so I was wondering if once I do up the tires and get a new custom tune it would help as well till I got a re gear. 

Posted
5 hours ago, Vblock said:

Yes it does! Do you have a tune? I know it’s not a permanent solution to the bigger tires and the tranny but I have a custom tune so I was wondering if once I do up the tires and get a new custom tune it would help as well till I got a re gear. 

Yes I have the edge tuner . It adjusts the speedo for bigger tires, de activated the AFM. I used the edge values for the trans shift points It cleaned up some of the sluggish shifts and downshifts smoother. I have the throttle management as well set at 20%. Also a cold air intake , I’d say is a waste of money but it all works together. A good tuner is a great buy. I recommend the hand held , some complain about dead battery with the ones plugged into the obd port. 

Posted
1 hour ago, Hutch72 said:

Yes I have the edge tuner . It adjusts the speedo for bigger tires, de activated the AFM. I used the edge values for the trans shift points It cleaned up some of the sluggish shifts and downshifts smoother. I have the throttle management as well set at 20%. Also a cold air intake , I’d say is a waste of money but it all works together. A good tuner is a great buy. I recommend the hand held , some complain about dead battery with the ones plugged into the obd port. 

I have a diablosport i3 with a custom tune from lew so he tweaks all that stuff for me. 

Posted
1 hour ago, Vblock said:

I have a diablosport i3 with a custom tune from lew so he tweaks all that stuff for me. 

I’ve read good reviews about lew. What lift and tire/ wheel setup are you going to do?

Posted
1 hour ago, Hutch72 said:

I’ve read good reviews about lew. What lift and tire/ wheel setup are you going to do?

I have 33x12.5 on 20x10s with a -24 offset on a level right now. I wanna do either a 4 or 4.5 lift with 35s. Lift will depend on how much money I wanna spend. It will either be the 4 in BDS or 4.5 zone.

AEF8186F-2859-4A2D-A839-C78AB1754B51.jpeg

  • Like 1
Posted
1 hour ago, Vblock said:

I have 33x12.5 on 20x10s with a -24 offset on a level right now. I wanna do either a 4 or 4.5 lift with 35s. Lift will depend on how much money I wanna spend. It will either be the 4 in BDS or 4.5 zone.

AEF8186F-2859-4A2D-A839-C78AB1754B51.jpeg

That bds system will put a smile on your face. Amazing how a 35” tire fits those 4” lifts. 

  • Like 1
Posted
3 minutes ago, big papa said:

Zone 4.5"  

20190427_153754 (2).jpg

The ability to keep factory wheels is a big bonus. Very nice truck.

Posted

The truck came with ugly 17s.  I bought aftermarket copy 22s.  I love not having crap thrown all over the side of my truck.

 

  • Like 1
Posted
That bds system will put a smile on your face. Amazing how a 35” tire fits those 4” lifts. 
Agreed[emoji106]

Sent from my LG-G710 using Tapatalk

Posted
On 6/12/2013 at 5:46 PM, plunk77 said:

saw on facebook Rough Country has released its leveling kit and 2.5" lift for the 2014. they look exactly the same as for the previous generation. But, they have a video that shows a new silverado with a 2.5" on it. although its a little low for me, it looks amazing

 

 

http://www.roughcountry.com/suspension/4wd-chevy/1500-leveling-lift-kit_1303.php

A shout to plunk77 for starting this thread almost 7 years ago. So many pages of info and great pictures. So glad this thread never died.

  • Like 2
Posted
Looks great!
 
i have 275/70r18 K02s on mine. 
 
rides like a slug considering I have the 3.08 gears. You didn’t have to change out your rear shocks for the 6.5 lift? I didn’t think the Bilsteins would be long enough



I got you. When I ordered my truck, I went with the biggest gear ratio they offered at the time. Yes, I contacted Bilstein and they provided me the part number, to order the right rear shock. I went on eBay and ordered it for around $175 shipped. I knew I was going to lift my truck, prior to leveling it, so I went ahead and got the rear shock to allow me to just swap them out.
  • 3 weeks later...
Posted
On 2/22/2020 at 11:35 PM, GrizzTheCat said:

Please help. My knowledge on lifts is very limited. Would you recommend a 4.5 inch lift or a 6 inch lift for mine? I have Bilstein 5100s on it, would I be able to keep them?

6A9FB5D1-4D67-428C-B6C8-5B87E5ACBB34.jpeg

hey man whats the set up you have on your truck in this picture. i like it 

Posted
7 hours ago, fireguy476 said:

hey man whats the set up you have on your truck in this picture. i like it 

-275/70r18 BFG K02 tires

-Bilstein 5100s 2.5 inch struts and matching rear shocks

-I had the OE wheels painted as close to the shade of gray on body paint

-I debadged the truck minus tailgate Bow tie

-Added black Z71 badges to doors and grille

-Bought OE illuminated bow tie package which comes with illuminated grille bow tie and regular black for tailgate

-I’ve had 2 front end collisions so I had body shop swap the lower chrome mustache to the black one

-Took off the lower valance 2inch air dam

-20 percent window tint in front to match factory rears

-Windshield tint bra

-Added an OE drivers grab handle 

-Put on 4 inch black carbon running boards from Tyger

 

 

 

 

EA918489-580F-4F88-A7D7-3D5B605E06DD.jpeg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Google converting 98 4.3 spider injection to carburetor if all else fails. 
    • That computer lies!
    • My centre console USB ports haven’t been working and the one in the glovebox is starting to act up. When I plug my phone into the cord the radio will go black and stop playing, and the CarPlay is inconsistent.   I checked the fuses and they were fine. I changed the USB port out and still nothing. Hoping for some advice on what I should be looking at.  
    • The truck is a 1995 Chevrolet S10 Blazer, 4.3 VIN "W" engine. :cracks knuckles:   On a whim - because I needed a headache - this truck was for sale so I stopped to take a look. Doesn't run. Well, it does, but barely. Long crank, choppy idle, bad misfire(s), it REEKS of fuel. I can DO this..I'm thinking. Diamond in the rough. One owner until last year. A young guy is selling it, he bought it 6 months ago. It stranded him more than once, he's got a newborn. It was in the shop 10 days ago and he "thinks" they said it needs a new fuel injection system. He can't put any more money into it, needs it gone. I was thinking of upgrading my Macbook, which is a total want, not a need. For less than the price of a new laptop I can have fun for months tinkering on this truck and enjoying it. I'm taking this truck home. The guy was beyond thrilled, his wife was there, she thanked me profusely, I could tell they were hurting. They seemed like good people in a bind.   Some parts, a wash, maybe a set of tires, and I can have a few months of fun and then turn it for beer money (or the next project).   Sure enough, there's a work order from a shop last week in the INCHES of paperwork on this truck dating back to when the first owner bought it. They put a new distributor in it, fuel injection work describes basically opening the plenum and putting it back together. He said he couldn't afford any more work so he had them button it up and that's when he put it up for sale.   I'm not well versed in 4.3. I did discover 1995 uses the 1992-1995 SCPI "Spider" injector which is riddled with issues from splitting lines, clogged or cracked poppet valves and plastic spider legs that crumble over time. Cool. I'll just order me a ne---. Oh, the auto parts store doesn't have it? Rock Auto doesn't have it. eBay? $$$$$$ for used. These are UNAVAILABLE period end of story unless you know "a guy" who's still got one in a box somewhere.   Can't upgrade to the '96-'04 injector, it's a different plenum, wiring/pinout and sensor config.   There are a few kinda "know a guy" -guy rebuild services for these injectors out there for about $350. Okay, Okay... I'd like to know if anyone has used them? Anyone got a lead on these crappy 92-95 spiders?   I also don't want to send MY spider to Narnia and back without knowing if that's truly the problem. I guess I'll need to pull apart the plenum and do some digging.   I was also thrown for a loop. This 1995 model year truck has an OBD-II connector. The interface is decidedly not OBD-II. I can read and reset trouble codes and view live data, but there's not a lot of data. Like misfire count and on what cylinder, that's not there. It's OBD-1.5.   Nothing is ever easy. Now it makes sense why this guy wanted to disappear this thing for cheap. I'm guessing the shop told him the injector is toast, the part is unobtainable and they're not going to sort sending the thing to a rando offering rebuild service on craigslist, and the kid likely can't be without a working car for 3 weeks even if they'd facilitate that.   Experience with these early SCPI's? Stories? Things to check? Sympathy? (..Nah...)   This can sit until I sort it. But I haven't had a problem with a vehicle I couldn't easily solve in a long time.    
    • I have four that read by the dash 8 to 10% better than miles/pump calculations and I have one that is spot on. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...