Jump to content

2014+ Leveling Kits

bcazier

By bcazier
in Modifications & Accessories

 Share

Recommended Posts

bcbz71 Enthusiast

bcbz71

Posted
Posted

Any of you guys have any shortcuts or pointers on installing the lower blocks of the RC 2.5 level? Didn't find many good quality videos. This kit, as bad as I hate to say it, kicked my a$$ tonight! I got the top spacers in but I pretty much did everything short of disassembling the whole entire front end tonight.

 

After spending a few hours doing my AMP Research steps, I decided to tackle the level also... Now I wish I hadn't! I am admitting defeat and bowing out gracefully! I'm not new to suspension work, but its mostly been limited to coilovers on sports cars, never any lifts or levels.

 

Jack one side up and support with jackstands.

Take off tire.

Disconnect steering joint.

Disconnect brake line on upper control arm

Disconnect sway bar nut or at least back the nut off as far as you can.

Discconnect upper ball joint nut (UCA)

Discconnect top strut nuts

Discconnect bottom strut bolts and pry off nutplates and discard.

 

Put in top spacer but only put the nuts on top of the strut on very loosely so you have play for the bottom.

Put in the bottom spacer with bolts from the top--threads down. I remember having to pry a little to get the holes lined up, but not bad.

 

The hardest part to me was compressing the strut to get the upper ball joint nut started. I hooked a ratchet strap to the top of the strut and the lower control arm until I could get the ball joint nut (UCA) started.

 

http://www.silveradosierra.com/suspension/2-5-rc-level-kit-install-2014-gmc-sierra-t350650.html

  • Like 1
  • Replies 7.7k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Saleenpowr
Saleenpowr

So i put my RC 2" level kit and Toyo 295/55/20's on this weekend. Install was simple, just like on my 2011. It definitely helps to have an extra set of hands when wedging that spacer in there. 295/

Saleenpowr
Saleenpowr

Thanks. Here is one more from yesterday. Considering we're getting 8-10 inches of rain the next two days, I won't be taking any better pics soon.  

FH212
FH212

Mine is finally done! After months of research I went with the RC 2.5" level kit front only, stock rear block. 20"x9" Fuel Nutz w/ +1 offset, 33x12.50x20 Toyo M/T tires. No rubbing, No trimming, yet a

Posted Images

gSwift Enthusiast

gSwift

Posted
Posted (edited)

Jack one side up and support with jackstands.

Take off tire.

Disconnect steering joint.

Disconnect brake line on upper control arm

Disconnect sway bar nut or at least back the nut off as far as you can.

Discconnect upper ball joint nut (UCA)

Discconnect top strut nuts

Discconnect bottom strut bolts and pry off nutplates and discard.

 

Put in top spacer but only put the nuts on top of the strut on very loosely so you have play for the bottom.

Put in the bottom spacer with bolts from the top--threads down. I remember having to pry a little to get the holes lined up, but not bad.

 

The hardest part to me was compressing the strut to get the upper ball joint nut started. I hooked a ratchet strap to the top of the strut and the lower control arm until I could get the ball joint nut (UCA) started.

 

http://www.silveradosierra.com/suspension/2-5-rc-level-kit-install-2014-gmc-sierra-t350650.html

Thanks for the reply. Top spacers were no problem. It was the rear bolt by the axle that had me kinda baffled. The directions said something like, you may have to move the knuckle to one side to gain clearance from the axle, or something like that. The lower control arm was bottomed out as low as it would go, and there's no moving the axle. I'm about ready to just have it done somewhere. I live out in the country so all my friends are 50 plus miles away. So needless to say, I was pretty frustrated! Edited by gSwift
arkenzo Enthusiast

arkenzo

Posted
Posted

Just front spacer.

Did you get a wheel alignment after? Was it necessary for just the top spacer?

2fst4u Enthusiast

2fst4u

Posted
Posted

I used the readylift video on YouTube. It is simple video on how to put there 2.25 leveling kit on but very similar to the rc kit. Took me about 3 hours from start to finish.

2fst4u Enthusiast

2fst4u

Posted
Posted

Sorry forgot to say I used this video to do my rc kit on the 16 gm and worked like a charm.

gSwift Enthusiast

gSwift

Posted
Posted

Well, the ready lift video showed me everything except for the lower block installation...which is what I need. The bolt by the axle seems so long that I see no way of getting the bolt in. I can get it in from the bottom up all day long. I'm beyond frustrated trying to get this lower block in.

arkenzo Enthusiast

arkenzo

Posted
Posted

Well, the ready lift video showed me everything except for the lower block installation...which is what I need. The bolt by the axle seems so long that I see no way of getting the bolt in. I can get it in from the bottom up all day long. I'm beyond frustrated trying to get this lower block in.

Show pics of what you are working with please. I've installed a full RC 2.5 on my previous 2014 Silverado and I managed to do it all with simple tools and a 1/2 ton floor jack lol, i'm willing to guide you but would need to see what you're seeing.

gSwift Enthusiast

gSwift

Posted
Posted

Show pics of what you are working with please. I've installed a full RC 2.5 on my previous 2014 Silverado and I managed to do it all with simple tools and a 1/2 ton floor jack lol, i'm willing to guide you but would need to see what you're seeing.

 

I appreciate the offer and the replies, but I called it quits and put the front end back together. As I mentioned before, i'm certainly not new to suspension work, but this one got the best of me. I'll take it to a local off road shop as bad as I hate to.

gSwift Enthusiast

gSwift

Posted
Posted

Show pics of what you are working with please. I've installed a full RC 2.5 on my previous 2014 Silverado and I managed to do it all with simple tools and a 1/2 ton floor jack lol, i'm willing to guide you but would need to see what you're seeing.

But just to try and clear up what I'm saying. The main thing that was giving me trouble was mounting the bottom block on the bottom of the shock. I calls to put the new bolt in from the top side, and I can get the bolt in on the hole nearest to the front of the truck. But the back hole of the shock is almost directly under the axle. Therefore the is trying to go in at a hard angle but the head of the bolt is hitting the axle.

Tim Rasmussen Enthusiast

Tim Rasmussen

Posted
Posted

But just to try and clear up what I'm saying. The main thing that was giving me trouble was mounting the bottom block on the bottom of the shock. I calls to put the new bolt in from the top side, and I can get the bolt in on the hole nearest to the front of the truck. But the back hole of the shock is almost directly under the axle. Therefore the is trying to go in at a hard angle but the head of the bolt is hitting the axle.

All bolts I put in on my readylift kit had them going in from the bottom up. This allowed for me to reuse the threaded clips that are connected to the shocks that act like a nut you could say. So for u to put them in from the top down makes me wonder how you would be able to use the factory threaded clip? Did the send nuts to go on the bottom of the spindle?

 

I would suggest putting the bolt in from the bottom up. My two cents.

gSwift Enthusiast

gSwift

Posted
Posted (edited)

All bolts I put in on my readylift kit had them going in from the bottom up. This allowed for me to reuse the threaded clips that are connected to the shocks that act like a nut you could say. So for u to put them in from the top down makes me wonder how you would be able to use the factory threaded clip? Did the send nuts to go on the bottom of the spindle?

 

I would suggest putting the bolt in from the bottom up. My two cents.

 

You don't use the threaded clip on the RC kit. You just pop the clips off and then they supply you with new bolts and nuts. Your kit sounds like it makes more sense. And I could go in from the bottom, but the bolt is so long and the lock nut so thick that its jamming into the bottom of the axle.

 

Guess i'll just leave it to the pro's haha

Edited by gSwift
bcbz71 Enthusiast

bcbz71

Posted
Posted (edited)

 

You don't use the threaded clip on the RC kit. You just pop the clips off and then they supply you with new bolts and nuts. Your kit sounds like it makes more sense. And I could go in from the bottom, but the bolt is so long and the lock nut so thick that its jamming into the bottom of the axle.

 

Guess i'll just leave it to the pro's haha

 

The bolts have to go in from the top. I think the problem is that you didn't take off the UCA nut completely and drop the hub.. I had the same issue. I tried to leave it on by one thread and pry the lower spacer in under the strut. Once you take the UCA nut off and the steering tie rod end off, you can articulate the hub any direction you want to get the bolt in.

 

As I think about it, I may have done the bottom spacer before the top spacer. The first side took me forever it seemed, but the second side was like 30 minutes total.

 

Here is my strut down before I took off the UCA and dropped it completely.

post-138034-0-71029700-1459082514_thumb.jpg

post-138034-0-71029700-1459082514_thumb.jpg

post-138034-0-71029700-1459082514_thumb.jpg

post-138034-0-71029700-1459082514_thumb.jpg

Edited by bcbz71
gSwift Enthusiast

gSwift

Posted
Posted

 

The bolts have to go in from the top. I think the problem is that you didn't take off the UCA nut completely and drop the hub.. I had the same issue. I tried to leave it on by one thread and pry the lower spacer in under the strut. Once you take the UCA nut off and the steering tie rod end off, you can articulate the hub any direction you want to get the bolt in.

 

As I think about it, I may have done the bottom spacer before the top spacer. The first side took me forever it seemed, but the second side was like 30 minutes total.

 

Here is my strut down before I took off the UCA and dropped it completely.

 

That may indeed be the issue. I was leaving the UCA nut attached, and by more than a thread or two. It seems as if I had watched a video where they took a couple of shortcuts and left that nut attached. But now that I think about it, I believe they went in from the bottom with the new bolts on the lower spacer.

 

Thanks for the reply! I think i'll give this one more try before I give up.

 

If only I had followed the directions word for word :banghead:

  • Like 1
arkenzo Enthusiast

arkenzo

Posted
Posted

 

 

 

If only I had followed the directions word for word :banghead:

Get'er done!

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,897
    Total Members
    8,960
    Most Online
    ncleg
    Newest Member
    ncleg
    Joined

  • Who's Online   4 Members, 0 Anonymous, 803 Guests (See full list)

  • Latest Articles

  • Posts

    • XY74
      Roll up bed cover experiences

      By XY74 · Posted

      I have a Retrax pro that I first had on my 2020 chevy and transferred it to my current GMC.  It stays in the garage most of the time, so hard for me to judge it's long term weather resistance.  It still works perfectly, been very durable.  It doesn't see oil patch usage, but it's not a mall queen.  It keeps most things mostly dry (small leaks) and the security of it is enough to slow someone down but not keep them out for long.  I would buy one again, it works for me.     
    • fm2176
      New to Me 2010 SLE (Quirks, Issues)

      By fm2176 · Posted

      Thanks to the convenience of Amazon, I was able to get a few things done to the truck today.  I installed Carquest Premium oil and air filters with five quarts of Mobil1 High Mileage 10-30 along with a quart of Pennzoil Platinum 5w-30 I already had.  The latch for the flip up center console lid was broken so I replaced it along with the power mirror switch.  I found my push retainer assortment this morning and reattached the plastic under the bumper and it was only held on with a few screws and retainers.  Then I programmed a new remote keyless entry fob so I can lock my dog in the truck when I take her out with me (I've got to keep the air going for her since it's been in the 100s).  Finally, I ordered some LED interior bulbs and replaced the reading lamps.  The front lights are working fine while one of the back lights only works intermittently and the other not at all.   While under the truck, I found the source of at least one of the noises: the sway bar links need replacing.  I ordered a set of Suspension Dudes links with Code Red bushings.  Never heard of them, but they're made in the USA and have decent reviews.  While making yet another Amazon order, I went ahead and added a set of front tow hooks.  I went with red, since that's the color of the sway bar link and bushings and it should look decent enough on a black and chrome truck.  Speaking of which, it doesn't bug me much, but the passenger side mirror has a chrome cap while the driver side doesn't, so eventually I'll make them match one way or another.  Oh, and I ordered a $20 TPMS reset tool.  No idea if it will do anything for my sensors but it was cheap and will work for the Ford Transit Connect as well.     For tradition's sake, I ordered a new oil change wrench.  I kept the Snap-On 9/16"x15mm GM wrench I bought when I was 18 in the 2006 GMC from the time I bought that truck until the truck was lost.  While I was tempted, there's no need to spend $80 for a new SO wrench, or even $50 with shipping for a used one on Ebay.  I just bought a Duratech 15mm extra-long ratcheting wrench to do the job as needed.  It works, and if I like that wrench enough, I'll buy the set.  
    • Another JR
      Multigate electrical problem

      By Another JR · Posted

      The recall is for exactly this issue - those drain holes combined with the limited environmental capability of the tailgate electronics card inside the tailgate were a problem. The “safety issue” was the potential for the tailgate to spontaneously open, but all kinds of tailgate misbehavior can occur from water contamination of that control card.    There is no real fix yet. The initial recall just disabled the tailgate. Later, when parts became available, they would replace bad parts with new parts of the same bad design. My dealer is going nuts because the few times I let them get their hands on my truck, my tailgate is off due to a slide-in camper installation. They really want to cut my tailgate wires, but I won’t give them the chance. I will let them get their dirty hands on it when a real fix (redesign) is available.  My tailgate, which works just fine with sealant plugging the drain holes, will remain safe in a dry storage crate until then.  
    • JakeD
      Tire fitment

      By JakeD · Posted

      Yes your absolutely right, I been looking at the 4 inch BDS one and it acutely states you can use the stock 20’s just not the 17’s or 18’s, I also didn’t realize that with my 275/60r20 stock wheels I’m already running 33 inch diameter wheel setup lol so I can just run my stock wheels and tires atleast to start.
    • davester
      Tire fitment

      By davester · Posted

      I would expect that to be lift-kit dependent.  If the kit has interference issues w stock wheels, then the kit/manufacturer should indicate that somewhere.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...