Jump to content

Recommended Posts

Posted

Can you do measurements of the amount of lift it adds, the rancho page says that it will make your truck able to run 35s but doesn't say what it needs to be paired with if anything.

 

I found only one video of a guy running 35s with them.

 

 

Sent from my iPhone using Tapatalk

35 won't work I ran my 305/55/r20 with the stock wheels and they run a little and now with my 20x10 they still rub a little that why I think 35 won't clear I bought the Rancho Struts thinking I would be able to clear the tires

 

 

SuperAllTerrain

Posted

35 won't work I ran my 305/55/r20 with the stock wheels and they run a little and now with my 20x10 they still rub a little that why I think 35 won't clear I bought the Rancho Struts thinking I would be able to clear the tires

 

 

SuperAllTerrain

Still not sure how this guy did it.

 

About 1 minute in

 

 

Sent from my iPhone using Tapatalk

Posted

RANCHO RS999901

Has anyone used this to replace the entire strut assembly to level my truck? I can do this easily. Otherwise I was going to go with the Bilstein shock replacement and have to get a spring compressor and all. Thanks.

thats the exact set up I did on my truck love it and did it in 30 mins my dad did the same thing and he loves it

 

 

SuperAllTerrain

Posted

Still not sure how this guy did it.

 

About 1 minute in

 

 

Sent from my iPhone using Tapatalk

He hammered and ground the hell out of his fenders. It's in his comments on the YouTube video.

 

"Take a grinder and big hammer to the back fender about 1" or less, and with the front you need a heat gun to move the molding or just cut the plastic"

 

 

Sent from my iPhone using Tapatalk

Posted

He hammered and ground the hell out of his fenders. It's in his comments on the YouTube video.

 

"Take a grinder and big hammer to the back fender about 1" or less, and with the front you need a heat gun to move the molding or just cut the plastic"

 

 

Sent from my iPhone using Tapatalk

Plus the control arms?

 

 

Sent from my iPhone using Tapatalk

Posted

Plus the control arms?

 

 

Sent from my iPhone using Tapatalk

I'm not sure what you're asking? But changing control arms won't really allow you to stuff a larger tire.

 

Some MIGHT allow you to fit a slightly wider one if you're having issues with a large positive offset and rubbing tires on the alum/stamped steel control arms. But only if the new control arm shape doesn't stick out quite as far where that rubbing occurs.

 

You might need the new UCAs to take advantage of any extended travel you might have with the new height, if any.

 

 

Sent from my iPhone using Tapatalk

  • Like 1
Posted

Without reading 373373 pages, if I'm looking for 2", is it better to space above, space below, or split the difference to minimize harsh suspension travel.

  • Like 1
Posted

Without reading 373373 pages, if I'm looking for 2", is it better to space above, space below, or split the difference to minimize harsh suspension travel.

Dont think it matters much, think most 2 inch are lower and easier to install. 2.5 and up seem to be both.

Posted

Question for you guys. I cut off the service perches when I put my King coilovers on. Im probably going back to the stock set up but I wont have the perches anymore. Will my truck be ok without them in the stock configuration?

 

 

Sent from my iPhone using Tapatalk

Posted

I have a 2.5'' leveling kit installed on my 2015. It's a bottom U spacer only. Truck kreaks and moans at low speed under 25mph. Sounds like shit and rides pretty rough on the terrible SC roads where I live. I think its due to the limited down travel it has caused? Anyways I had a shop look at it and they said they couldn't figure it out as to why it made the noise. Im getting pretty fed up with it. I am looking at changing it up somehow but do not know what to get. I am thinking maybe the fox 2.0 coilers will solve the problem but they are pricey and would hate to install them and the noise continues. also looking at RC 3.5'' with uca's but have heard mixed reviews. Any suggestions appreciated.

 

thanks,

Posted

Mine and my dads. Both have 2.25" readylift level. He's running 285/75 Toyo at2s and I'm running 285/75 Toyo MTs. 127263daaac1496ab2fc7b8169490935.jpg

 

 

Sent from my iPhone using Tapatalk

 

any spacers used on this setup? any rub?

Posted

 

any spacers used on this setup? any rub?

No spacers, very minor rub on sway bars at a hard full lock with the MTs, no rub with the at2s. The tire shop zip tied the fender carpets. Both trucks have been "off road" crossing creeks, smaller water bars, and small ditches. I'm sure if I did major off roading like some guys on here I might have more problems, but I take it easy on my truck. I have atvs to get to the "backwoods."

 

 

Sent from my iPhone using Tapatalk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,980
    Total Members
    8,960
    Most Online
    Fishboat
    Newest Member
    Fishboat
    Joined
  • Who's Online   5 Members, 0 Anonymous, 550 Guests (See full list)


  • Latest Articles

  • Posts

    • Hey guys, sorry for the confusison about this. This wasn't my experainnce, it was copied and pasted fom the net. 
    • The problem with failure rates or increase failures are there’s people who don’t have a problem. What are you doing wrong they say. We had 4 5.7 GM diesel’s in the family when they came out. One was flawless. My uncle who happened to be the most abusive. Early rotary engines were known to use oil. I abused my first car so bad in six months I replaced the clutch, transmission and rear end. It didn’t use oil. My brother in law has a 2013 Tahoe and an older Yukon. The Yukon has 280K miles. The Tahoe around 175K. He runs them to about 300K. If his lifters fail before that time he would consider it a failure. My Hondas, I know people hate it when I mention them. Identical engines. One with cylinder deactivation one doesn’t have it. One shudders when the eco light goes on or off. Cylinder deactivation. But wait! According to the web. It can happen with lock up too. So now people in the know are changing the oil and transmission fluid more often. Then you read it could be a programing issue. So what do you do? There’s lots of money involved. I see three ways to deal with it. One only works if you don’t drive lots of miles. Lease, never get out of warranty. Or only buy older vehicles with a good track record. They all have bad runs. Usually when there’s a change. Even Toyota and Honda. 
    • Question @diyer2 on this line if you please. Are you saying the shudder is the system turning on and off at the frequency of the shudder? Guess I'm asking if you are saying you have seen it do this with the bi-direction scan tool in graph mode? If so have you been able to discern the 'trigger'. Something is telling to cycle rapidly.    My truck just started doing this recently. 197K on the clock. My response has been M5 anything under 55 mph. I treat it like a lugging stick shift. Gear down and let it spin a bit. Engauge M5, then tow mode and then M6 lets the trans stay in 5th but the AFM is active. Smooth like Skippy.    My thought was that as a machine ages the friction gets lower and as the system is load based, the lower friction would allow it to turn on at ever lower rpm until it reaches the lugging point. And yes I am ignorant of any minimum rpm requirement for the system. If you know that would be useful information.    As you know I run a Scan-Gauge II which allows me to watch the On/Off of the signal to the VLOM. While in the shudder mode I'm not seeing is cycle at that frequency or at all for that matter outside the triggers @newdude posted a few years back. Now is it possible that the refresh rate isn't fast enough to catch it? Maybe. It is why I asked my first question about graphing and trigging parameter.     As we have observed from members here the failure point is all over the map miles wise as you note yourself in your opening post. That by itself begs a few questions like fellows that comment on these lifters failing even after the system has been disabled. Long after. 😬   https://www.enginelabs.com/news/tech-tips-replacing-ls-active-fuel-management-lifters-with-melling/   The Gen5 lifters operate the same as the LS versions. In fact they are the same lifter.    https://www.enginelabs.com/tech-stories/sorting-out-gen-v-lt-lifter-failure-with-a-simple-valvetrain-fix/        
    • UPDATE 2: Steering wheel control backlights and control of the cluster can supposedly be achieved by adding a wire to pin 20 of the cluster and tapping it to pin 2 of the main clock spring harness. I'm going to give it a shot - will update  
    • GM Global A pickups 2019-2022 can do OTA programming for the radio.  GM VIP (GM Global B) can do OTAs for almost every module on board.  So a 2022.5 and newer pickup can do OTAs for recalls like the 2.7 fuel flow recall.  EVs get OTAs that improve one pedal driving, radio issues, HVAC issues, updated battery management software, etc.     So age of the vehicle/what GM electrical platform its on will alter what amount of updates can be pushed on OTAs.  
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...