Jump to content

Post your 2014+ wheel/tire set-up

BlueWrapper
 Share

Recommended Posts

  • Replies 5k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Full Lock
Full Lock

I'm in... Man I need some new pics if rain would stop messing up my truck ha   305/65 18x9.-12  

DLS-001
DLS-001

Mounted!     18-inch Method Mesh wheels, 275/70/18 BFG All Terrain tires, and a 2.5-inch RC level (front only). Zero rubbing, zero road noise, nice traction on and off road, and no wobbly street

daowens
daowens

Fuel Maverick 20x9 +20 Nitto Trail Grappler 295/55R20 Rough Country 2.5" Leveling Kit No rubbing or trimming        

Posted Images

CptMcSaug Enthusiast

CptMcSaug

Posted
Posted

Anyone have a recommendation for a tire that won't go flat every time you drive past a small cactus in west Texas.

 

 

Sent from the future via a wifi time portal.

Cooper ST MAXX is super chip resistant and nice looking.

Mike1220 Senior Enthusiast

Mike1220

Posted
Posted

Anyone running 285/75r18 tires on a leveling kit? It's roughly 34.5" by 11.5."

I've seen a 285/55/22 on a level kit. Roughly the same dimensions (with some plus or minus to account for differences between manufacturers) but the few I've seen with that set up (285/55/22) didn't have any rubbing issues so I would think that a 285/75/18 would work also. But I have no first hand experience so I can't say for sure if they will work or not. But theoretically, you should be good

Michael94 Enthusiast

Michael94

Posted
Posted

2014 Silverado LT double cab

 

20x9 +18 Fuel hostage

285/55r20 Mickey Thompson ATZ p3

2.25 Readylift Leveling kit

post-128822-0-60534300-1421384560_thumb.jpg

 

Stock 20s powder coated black

LT275/65r20 Studded winter tires

7 inch rough country lift

post-128822-0-08793700-1421384823.jpg

 

20x12 -44 Fuel hostage

35x12.5r20 Toyo MT

Waiting for spring to mount. Hopefully they don't rubb to bad

post-128822-0-69828800-1421384904_thumb.jpg

post-128822-0-98390300-1421384935_thumb.jpg

post-128822-0-60534300-1421384560_thumb.jpg

post-128822-0-08793700-1421384823.jpg

post-128822-0-69828800-1421384904_thumb.jpg

post-128822-0-98390300-1421384935_thumb.jpg

post-128822-0-60534300-1421384560_thumb.jpg

post-128822-0-08793700-1421384823.jpg

post-128822-0-69828800-1421384904_thumb.jpg

post-128822-0-98390300-1421384935_thumb.jpg

post-128822-0-60534300-1421384560_thumb.jpg

post-128822-0-08793700-1421384823.jpg

post-128822-0-69828800-1421384904_thumb.jpg

post-128822-0-98390300-1421384935_thumb.jpg

  • Like 3
justin283 Enthusiast

justin283

Posted
Posted (edited)

Wrangler Duratracs 275/65/20 2.5 RC leveling kit installed. Very slight rubbing, trimmed a few inches off one corner of the wheel liner and it no longer rubs.

qMeFVyD.jpg

Edited by justin283
  • Like 2
diggman08 Enthusiast

diggman08

Posted
Posted

Justin, looks good, those tires are up in the wells pretty good, maybe a 4" lift?

 

I have same lift as you and going with a 34-34.5 x 11 and haven't decided a 4" will be enough.


do you have any front or rear pics?

thetruck454 Enthusiast

thetruck454

Posted
Posted

I had my 20" fuel mavericks swapped out for factory ck190 22" wheels.

 

Sorry the truck is dirty.20150117_164616-1_zpssgz9dshd.jpg20150117_164636_zpsxw6mmiki.jpg

Going a different direction instead of lifting the truck?

never_rested_24-7 Enthusiast

never_rested_24-7

Posted
Posted (edited)

Going a different direction instead of lifting the truck?

Planning on leveling with a Nitto Terra Grappler G2 285/50/22 tire. Ive wanted these 22s forever and I finally found a heck of a deal on a set so I jumped.

 

Also my nfabs will be for sale also.

Edited by never_rested_24-7
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      Correct way to service 2024 l8t allison trans?

      By Chuck FB · Posted

      I have never seen GM instructions for the other trucks as per the HD with the 6 speed or the half tons but had got the impression that the HD trucks with the 6 speed were not having the same problem that the 10 speed and pan presented. Also video that I have seen of the HD 10 speed with the gas engine starting in 2024 model year showed that it was a real struggle to even make it work when pulling down hard on the exhaust after undoing the exhaust hanger bracket on the side of the transmission as after all there is little room for the pipe to even go down behind the Y joint as it soon would hit a frame cross member. Also that they had tried just like I did with the gasket off and no way was that pan coming out any way they tried to manipulate the pan. From that as well as the local transmission shop talking about the pain in the rear issue, I was not expecting my pan to come out because GM shows it was not even intended to come out without dealing with the exhaust piping.    It would be nice to claim, here's what you do and its easy to remove the pan guaranteed on any HD truck with the gas 10 speed but dollars to donuts the next guy trying what I did would not have the same luck as the exhaust was just manufactured slightly different and be pissed off at my claim that the pan comes out with no issue. Its more of a try and see if your particular truck might work like mine did .... or not !. 
    • carkhz316
      Correct way to service 2024 l8t allison trans?

      By carkhz316 · Posted

      Sorry I didn't see this until now, but it works on both the 6 speed and 10 speeds, as well as all the half tons too.
    • 1998sleaze
      Engine vibration after motor mount replacement.

      By 1998sleaze · Posted

      Hello, I have a 2018 GMC Sierra 1500 that I recently changed both motor mounts on due to the driver's side being blown out. After replacement I seem to have a steady vibration that I can feel in the pedals and the back of the seat. At this point I'm convinced that the aftermarket "Anchor" branded mounts I used are not performing as well as OE, the only real reason I ended up using the mounts in question was because my local dealers were out a few months to get a Driver's side mount. I've tried "Neutralizing" the mounts according to the motor mount TSB published for these truck to no avail. My trans mount is also in great shape and seems to be absorbing vibrations swimmingly. As far as I can tell there is no issues idling, my idle RPM is steady and I've recently put GM plugs and wires on, however, I have not cleaned the throttle body or intake valves. Any one else have a similar experience with aftermarket mounts? Patience certainly is a virtue that I wish I exercised here. Thank you!
    • CamGTP
      Winter Returned

      By CamGTP · Posted

      I still saw people out for runs, on their bikes/motorcylces, jeeps with the doors off driving around here the past 2 days. I guess we are just used to it here haha.   Tasted like a bonfire the last 2 days.
    • CamGTP
      6.2L (L9H) Owners - Get all your questions answered here

      By CamGTP · Posted

      The TCM has to be flashed before it can drive.   If you installed it the way it is, it has the OS (operating system/program) from the 2010 truck you got it from. That will not match with the VIN/OS pair that your 2013 truck has.   You can do the full install. Then tow it to a dealership and they can flash the trucks PCM/TCM with the latest program for your VIN.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...