Jump to content

Cargo Lights on with Reverse Lights

El Conquistador
 Share

Recommended Posts

  • Replies 357
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

El Conquistador
El Conquistador

Okay so I was inspired by 2 threads here, one being the fog lights on with high beams, which I did and love. The other is a thread about putting a switch in the bed by the tailgate to turn on the car

Crooks
Crooks

Did you jam it in far enough? She will take it

morrislee
morrislee

Hello,   Good idea, but I took your step little different. I have the puddle light and I tapped into that.     This way, when vehicle is in "run" position, puddle lights and the cargo lights w

Posted Images

iamdanieltuck Enthusiast

iamdanieltuck

Posted
Posted

I bypassed the not working in drive function using a PAC tr7 module triggered by the cargo light momentary ground and have it activating the cargo light relay. Simple and effective. I can write it up better later if anyone is interested.

 

 

 

I'm with Derbaby, someone help us figure out how to get the towing mirror lights and the cargo lights to come on while in Drive without shifting to Neutral.

 

Thank you again to those who've figured out how to get the fog lights to stay on with high beams and the cargo lights with reverse lights, now, just this last missing piece of the puzzle.

 

Sent from my iPhone using Tapatalk

iamdanieltuck Enthusiast

iamdanieltuck

Posted
Posted

I am looking into a solution that only requires a wire. It seems the in drive interrupts the + signal to activate the relay. If I'm right, it will only take running a wire from driver side in front of door to passenger side fuse box and putting a diode in to prevent feed back to bcm. I tapped my low amp + input to the back of the passenger fuse panel control wire for the cargo light relay (which plugs into the back of that fuse panel).

 

 

Sent from my iPhone using Tapatalk

C4Ranch Enthusiast

C4Ranch

Posted
Posted

Hello,

 

Good idea, but I took your step little different. I have the puddle light and I tapped into that.

 

attachicon.gif2014-11-26 16.22.17.jpg

 

This way, when vehicle is in "run" position, puddle lights and the cargo lights will be completely off (as would the cargo light switch would too)

 

I also have a overhead canopy light, so it HAS to be off when backing up.

 

I have attached the diagram, REMEMBER, the orientation of the diagram is with the plug out, and the plug end facing you with clip fastener facing up!

 

attachicon.gif2014-11-26 09.01.06.png

 

**** TIP****

I have had trouble keeping the leads of the diode in the wire socket, I end up sanding it sharp so I can get it in deeper next to the exposed area of the wire. IT ALSO HELPS if you wiggle the wire to the opposite direction it is leaning on to and insert the leads in that side. Wiggle the wire to the other side allows it to push back and keep the leads of the diode in the pressured position to maintain a solid connection.

I've been wanting to turn my cargo lights/trailer mirror lights on while driving so I can see my rear tires in the dark on the trail.

 

Looking at the diagram above, I wonder if I could tap off the child safety switch to make it switch activated? The switch is useless to me right now.

 

Thoughts?

iamdanieltuck Enthusiast

iamdanieltuck

Posted
Posted

I did it with a latching relay. I posted how I did it in the 2500 forum

 

 

I've been wanting to turn my cargo lights/trailer mirror lights on while driving so I can see my rear tires in the dark on the trail.

 

Looking at the diagram above, I wonder if I could tap off the child safety switch to make it switch activated? The switch is useless to me right now.

 

Thoughts?

 

Sent from my iPhone using Tapatalk

6.2Midnight Enthusiast

6.2Midnight

Posted
Posted (edited)

Then just follow the instructions in this thread. I thought you meant about working in drive

 

 

 

Sent from my iPhone using Tapatalk

I'm with you, I want mine to come on while in drive as well... Edited by 6.2Midnight

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.3k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,716
    Total Members
    8,960
    Most Online
    BDS my HD
    Newest Member
    BDS my HD
    Joined

  • Who's Online   0 Members, 0 Anonymous, 476 Guests (See full list)

    • There are no registered users currently online

  • Latest Articles

  • Posts

    • BDS my HD
      Brand new to this forum. Questions about re-gearing my 26’ HD

      By BDS my HD · Posted

      Hello hello looking forward to expanding my knowledge of the 2026 2500 HD that I just bought.   Truck has 3500 miles on it four-wheel-drive crew cab and I’m about to put a 6 1/2 inch BDS lift on it 18 x 10 -25 offset with 37’s   Already have the wheels and tires just waiting on the lift install in about three weeks   Question what surprises am I not gonna be happy with?  I’m not new to lifted trucks so I know that acceleration towing gas mileage all that is affected..   Question is those of you that have this truck this powertrain with a 10 speed Allison and have done the mods that I’m doing,,, how bad is it? Is that Allison constantly gonna be hunting for the right gear to go into? And what about towing, acceleration, fuel consumption as mentioned?    Lastly how come I can’t find any ring pinion gear set up for these axles and when could I expect to see them?   I apologize if there’s any typos I’m doing speech to text on my iPhone.    
    • linc45bn
      2013 2500HD 6.0L intermittent no crank no start

      By linc45bn · Posted

      I've got a 2013 2500 6.0L Flexfuel. Drove the truck earlier today with no issues. Went to run an errand tonight and noticed key fob wouldn't work. Figured battery was dead, so replaced fob batter. Still wasn't working. Grabbed my other set of keys with the other fob and that one wasn't working either. So I manually unlock truck and insert key. Interior lights come on, dashboard lights up, turn key and truck starts. Turn truck off, like a moron, and try starting again. This time no crank, no click, no nothing. Lights still come on and dash lights up, but now I'm getting a service 4wheel drive, service tire monitor, etc. Check voltage on battery and Im showing 12.2v. Throw my battery charger on it and give it 15 mins and try starting again. But still no crank no start. Decide maybe its a bad battery, run to autozone grab a new one and put it in. Same issue. Disconnect battery and let it sit for 15 mins. Try again and still nothing. I had managed to roll the windows down earlier as its a humid night, but now I can't get them to roll up. Power locks are also not working now. Then randomly I try the key again, and it fires right up. Immediately I roll up the windows as we have nothing but rain forecast this week. I shut it back off wait 30 seconds and start up again. Worked a 2nd time. So turn it off, start putting things back together. Try one more time, and back to no crank no start. And now the car alarm starts going off. Had to disconnect battery and leave it that way for the night as I don't think my neighbors would appreciate my alarm going off again tonight. Any thoughts or help would be appreciated. 
    • Grumpy Bear
      first oil change - 2026 2500HD gas

      By Grumpy Bear · Posted

      No one will care for you like you care for you. Do what you can for as long as you can. IMHO of course. 
    • Grumpy Bear
      Oil Consumption

      By Grumpy Bear · Posted

      How about them NICKS!!! 
    • Peoplemvr
      GMC 1500 Illuminated Front Grill Emblem REPLACEMENT.

      By Peoplemvr · Posted

      Hi there.  Long time lurker, first post.    i have read the previous posts regarding the water ingress problem with this emblem.  I bought my 1500 SLT the  summer of 2025 new and after reading the MANY problems with these emblems failing I decided to install one anyways.  As per a YouTube video, I sealed ( or tried to) this sign with silicone sealant around the outer perimeter joint and the holes that were already somewhat sealed on the rear plate of the emblem.  And installed the connector assembly using dielectric grease on the connectors. The installation looked great and worked well for about 4 months……then FAILURE.  Grrrrrr…… I live in the great white north and wash my truck weekly in an automatic car wash  to keep the salt off.  Let me tell you that removing the old, failed emblem is a whole different animal than removing the OEM individual letters without removing the grill assembly. Mainly because the illuminated logo is built differently than the original letters which  you can remove the red surface lettering with a knife or some kind of blade which gives access to the tabs which hold the logo onto the grill. So I had to essentially destroyed the old emblem to remove it. Doing so killed my chance of doing somekind of autopsy on the failed , old logo.  But there was plenty of water inside when I ripped it apart.  Prior to installing the new assembly I tried it with the old harness and it works fine.   Does anyone have any insight as to where the water is getting into this emblem? I intend to seal the new logo with slow curing epoxy this time around using a syringe.  I think this newer emblem may be an updated unit which I hope GM got the vendor to fix. It has an October 2025 date on it.    If this one  fails,  I am just going to revert back to the non-illuminated letters….AFTER PULLING THE GRILL.    Any thoughts on sealing with epoxy would be appreciated. Thx!   Doug  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...