Jump to content

2014 SLE Fog Light installation...

Bittner58

By Bittner58
in Modifications & Accessories

Recommended Posts

Bittner58 New Member

Bittner58

Posted
Posted

So far I have read lots of great advice in the forums about upgrading the 2014 SLE.

I really want to add fog lights to mine. I understand that this could be done, and shouldn't be too much trouble. I know that I will need to get a new dash switch, the bezel, lights and a wiring harness. I am having trouble finding out if that is all that I will need. Additionally, I was wondering if anyone has done this upgrade, I know people have tried installing the LED SLT headlights with little or no success.

If you can provide any advice, technical information and part numbers, it would be greatly appreciated! Ive been having trouble finding all the info I need.

 

Thanks in advance!

 

-Bryan

yojo Enthusiast

yojo

Posted
Posted

I'm in the same boat..Here is what I have so far. bezels gm#22902334 & 22902335 50.30 each

Bittner58 New Member

Bittner58

Posted
  • Author
Posted

Thank you for the specific part numbers. I would like to have the part numbers for each of the pieces to this puzzle, especially the wiring harness and headlight switch. I would assume once I have those specifics, it is rather easy to put together the rest.

I have found several websites that list parts for GMC's, but have never ordered from any of them, are there any that you would recommend? I would assume that you haven't gone through the dealership for those bezels, as the dealership would probably charge a bit more for some molded ABS plastic...

Any more input by anyone would be greatly appreciated.

  • 1 month later...
  • 8 months later...
Julio13 Enthusiast

Julio13

Posted
Posted

Just bought a kit eBay has fog lights wiring and switch for 58 dollars like the factory fogs

  • 1 month later...
armallard Enthusiast

armallard

Posted
Posted

Did you get these installed? I would like to do this to my 2011 did you put the switch in the dash? and how hard was the wiring? pics and part # would be nice also thanks.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Gkistler
      2015 Sierra Denali L86 cyl 5 misfire at idle

      By Gkistler · Posted

      Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • zibzer2
      Pulsating Noise 4Cyl Mode

      By zibzer2 · Posted

      2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Chuck FB
      Some Assembly is Required

      By Chuck FB · Posted

      Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      He is not saying that an SAE *W20 will have more viscosity than a *W40 due to MORE VII polymers. He is saying that although multiple *W40 may post in the PDS the same or similar 100 C and 150 C viscosities that the blenders choice of modifier TYPE and AMOUNT to get his chosen base to grade will not give identical real world viscosities in shear and at temperature. All will pass the SII test but not all will pass the 100 C HTHS (unpublished value) testing the blender does and relies on to get the required by law "percentage improvement' referenced to his last great work.    Tis the problem with the lie. Once told others are required to support it. 
    • PunchT37
      Parking Brake - Automatic Engagement Questions

      By PunchT37 · Posted

      I have a `25, 1500 that auto sets on incline. Never knew that at first. I have the electronic shifter. Just think if it didn`t do that? Unlike a mechanical shift that you can muscle out of park, how would you get this thing out? That would be a problem.   What I found out later is, I don`t have to push the button to release. Just put it in gear.   Setting parameters? Don`t know if it`s possible.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...