Jump to content

Fender Flares

spenpet

By spenpet
in Modifications & Accessories

Recommended Posts

spenpet Enthusiast

spenpet

Posted
Posted

Hello all!  So I went hunting this weekend and down some gravel roads...and I believe i picked up some paint chips...DOH!!   I don't have overly aggressive tires (285/65r18, on stock rims) but apparently enough to toss some rocks...so...I am looking for some fender flares that aren't too aggressive, just good coverage.  I like the clean look of the Bushwhacker Extend-A-Fender (i prefer to not get the fake bolts).  

 

Do you have any recommendations of something similar?  the Bushwhacker are damn expensive, anything that is comparable but not quite as much?  (or is this the case of you get what you pay for?)

 

anyway, also I have seen some OEM fenders for sale, didn't know if they had any coverage or would just be a hint of a lip sticking out...

 

looking for suggestions!  thanks in advance!

Waaazooo Senior Enthusiast

Waaazooo

Posted
Posted

I’m interested in knowing too. I would think mud flaps would do more that fender flares though. But bushwhacked catalog doesn’t show pocket flares for the standard bed.


Sent from my iPhone using Tapatalk

Bhurt Enthusiast

Bhurt

Posted
Posted

I am in the same boat, and the rock chips are on the front of the rear wheel wells, d'oh.  It looks like the rock gets stuck in the tires and comes out going forward when the tire is turning back down towards the ground.  I have been thinking of using the Husky long john flares on my truck but only having them stick out about 1/2" at the top, just enough to save the paint.  Does anyone have these installed?  They look like just a flat piece of rubber/plastic so they shouldn't to hard to install and adjust to how much a person wants sticking out.  

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      The not as clean as one would assume theme with the new engine oil, that reminds me of comments over the years with mechanics not always being so on board with filling an oil filter, not from the center anyway due to that typically being the clean side of the filter, danger of some contaminant falling into the filter if not careful but the realization now that the oil may not be as pure as one had assumed it would surely be. Yes it would be possible to fill from the small holes but that means messing with something to prop open the anti drain back valve if the filter is so equipped and not damage that valve in the process. Me, I have hardly ever prefilled an engine oil filter however I have prefilled diesel fuel filters with a filter on a fuel bulk tank and for anyone that has messed with diesel engines with filters and units that have a limited or no way of priming them, putting on a dry filter is a bad day to say the least with those crappy systems. But anyway back to not so clean engine oil, indeed perhaps its not so bad after all that I have not made a practice of prefilling oil filters.    As Grumpy Bear commented on keeping things clean, that I really have to wonder what the typical practice is at a dealer or any other shop that changes engine oil, do they make sure to wipe or wash off the oil plug and certainly if it fell into some gunk or onto a dirty floor, or that they wiped the filter mounting flange and didn't go and use some dirty rag and end up adding dirt to the inside of the head of the filter mount. Or be careless in how they stored or handled the new filter and if they were bumping into items under the vehicle with the filter opening facing up and having dirt drop right into the filter and if so right into the threaded center that is on the clean side. The top side, did they clean away the built up gunk that may be around the filler before removing the cap or to be really careful at that point that something right close to the filler hole that was hidden under the caps flange won't fall into the engine. Or did they clean the funnel or was that just laying there covered in oil from the oil change before and dust kicked up from sweeping the floor stuck to the oil and now that will go running into the next persons engine due to just not cleaning the funnel as "they won't know anyway" attitude as that young guy is more worried about taking a break so he can go outside and smoke a joint. Just random points that came to mind when I think about what some hired personnel may do that the shop foreman has no idea of or perhaps the whole attitude of some shops may be "eh ... who cares, they will never know the difference anyway".  
    • CamGTP
      Gas Prices

      By CamGTP · Posted

      $3.69 for 87 octane.   $4.24 for Diesel in town.
    • Atlas
      OCI, not when but why?

      By Atlas · Posted

      On the subject of OLM, Gm's OLM tool may be more "informed" than others brands. I recall OLM's in mid-2000's Chrysler products literally counting down a set number of miles. That's all the OLM appeared to be.    I would actually expect GM to be able to explain the parameters that their OLM takes into account from a high level. No, I would not expect them to disclose their software coding or data analysis around their parameters.   So we're talking about two different topics, so to continue the subject on the other one, I'd be curious to know how much "standard particulate matter" in fresh oil is able to be filtered at first start by a fresh oil filter. How much particulate matter is enough to "matter"?   I.e. how much of a "lever" do we think this equates to (variability in particulate content, in fresh oils, between different makes/brands, some which filter less, and some that filter more).   We can say that more particles = more wear = shorter engine life as a logical statement and use that data with a little marketing to scare people into selecting a more refined/filtered oil. Using a similie, is this like deciding to forego two alcoholic drinks in a lifetime because we're worried about the potential impact on lifespan? Are there numbers which translate the ISO test results into a quantifiable increase in wear for a given engine/use case?
    • chris21
      Brand new to this forum. Questions about re-gearing my 26’ HD

      By chris21 · Posted

      I'm pretty sure it doesn't actually recalibrate the speedometer it just changes the wheel speed sensor inputs to the computer. The truck still thinks it has stock tires.
    • asilverblazer
      OCI, not when but why?

      By asilverblazer · Posted

      I apologize, I missed this post, at risk of going off CURRENT TOPIC.   I'm not saying it is BS, I'm questioning how much information is being held back. GM is NOT going to spell out exactly every parameter in the algorithm. Liability, intellectual property, etc.    I'm not naive enough to believe that it is as simple as revolutions, coolant temperature, miles, time; are you?    I don't do irrational either, and boiling the OLM down to four simple values that I could code in an afternoon (I'm not a coder) is irrational - unless it suits your agenda to ignore it. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...