Jump to content

Recommended Posts

Posted

My manual reads that the plug outlet on my dash is good for cell phones and mp3 players.  Has anyone tried powering other things like small vacuums or power tools with this outlet?  I've never used it and wondering what it is capable of powering without harm to device or vehicle.

Posted

I’ve powered a hedge trimmer with it.

 

I feel like I’ve powered a few other things but forget what they were. Never had any issues. But definitely a hedge trimmer on multiple occassions.

Posted

Anything that is more than 150 watts or draws more than 15 amps will cause the outlet circuit to shut off as a protection. Power tools and vacuums are likely a no-no

  • Like 1
Posted
7 minutes ago, bkesting said:

Anything that is more than 150 watts or draws more than 15 amps will cause the outlet circuit to shut off as a protection. Power tools and vacuums are likely a no-no

The hedge trimmer I use is 3.3amps, or 363 watts@110volts.

 

You’re talking about 15 amps @ 12 volt, and nobody is going to know what their 110volt tool draws unless they do the math, which most won’t.

Posted
1 minute ago, truckguy82 said:

The hedge trimmer I use is 3.3amps, or 363 watts@110volts.

 

You’re talking about 15 amps @ 12 volt, and nobody is going to know what their 110volt tool draws unless they do the math, which most won’t.

I'm just going off what the owner's manual says:

 

"If equipped with this power outlet, it can be used to plug in electrical equipment that uses a maximum limit of 150 watts.

 

An indicator light on the outlet turns on to show it is in use. The light comes on when the ignition is in ON/RUN, equipment requiring less than 150 watts is plugged into the outlet, and no system fault is detected.

 

The indicator light does not come on when the ignition is in LOCK/OFF or if the equipment is not fully seated into the outlet.

 

If equipment is connected using more than 150 watts or a system fault is detected, a protection circuit shuts off the power supply and the indicator light turns off. To reset the circuit, unplug the item and plug it back in or turn the Retained Accessory Power (RAP) off and then back on.

 

The power outlet is not designed for the following, and may not work properly if they are plugged in:

 

- Equipment with high initial peak wattage, such as compressor-driven refrigerators and electric power tools

- Other equipment requiring an extremely stable power supply, such as microcomputer-controlled electric blankets and touch sensor lamps

- Medical equipment

 

 

Posted

powered a slow cooker on low setting while driving to a party.

I also plugged in the air mattress blower/inflator.

  • Like 1
Posted
20 minutes ago, aseibel said:

powered a slow cooker on low setting while driving to a party.

I also plugged in the air mattress blower/inflator.

Both are actually some handy uses.

I've been struggling to figure out why they would add them.  Most chargers are just USB and can plug into any cig lighter.  

You never really know when you're going to need it guess.  Just handy to have it. 

Posted
19 minutes ago, Logan Lanfear said:

Both are actually some handy uses.

I've been struggling to figure out why they would add them.

So what are some other uses that folks have successfully used this plug for?

Posted

We had a 3 hour drive to Thanksgiving dinner last year, wife plugged in our crockpot and cooked baked beans all the way. Smelled pretty good!!

  • Like 2
  • Haha 2
Posted
21 minutes ago, kevinfranklin said:

So what are some other uses that folks have successfully used this plug for?

Laptop charger.

Posted

My wife plugged in the crockpot,but she put it on high,it did not work. I can't remember if it works on low or not. I do know it worked on keep warm. 

Posted

I have found the 110V plug to be pretty useless. I charger my drill battery with it once and a laptop once. But it cuts off for my Air Pump. I wish you could easily upgrade the inverter to a 400w. Competitor trucks have 400w inverters. 

  • Like 1
Posted

Ya my 17 Ferd has a 400 watt inverter. It’s still pretty junky, modified sine wave. Dumps a ton of noise into the audio system too, only good for laptop.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • That makes sense, and I think you are describing the real product problem. Capturing data is the easy part. If the owner or technician has to manually dig through five minutes of millisecond-level logs, the product has already failed. The device would be at the ECM harness, not at the OBD port, so I agree that data retrieval and event marking need to be thought through carefully. The way I am thinking about the architecture is: The recorder itself should not depend on a phone, app, Bluetooth, Wi-Fi, or cloud connection to capture the event. It should always keep a local rolling buffer and lock the event locally. A button, phone app, or small cabin device would only act as an event marker. If the driver feels a stumble and presses the button 10–30 seconds later, the pre-buffer has to already contain the useful data. For data retrieval, the practical options would be a sealed service USB lead, Wi-Fi download, or a phone/cabin companion device. I would not expect the owner to remove the ECM-side module or work with raw files directly. The cloud or AI side would be for interpretation, not for capturing the event. The truck may have no connection when the issue happens, so the evidence has to be saved locally first. After that, cloud processing could help decode the data, compare it against baselines, and generate a readable report. For the first version, I would keep the automatic triggers conservative and objective: driver event marker bus-off error passive voltage drop / brownout device reset FIFO or queue overflow a normally periodic message disappearing side-to-side communication mismatch, if the topology supports that For “learning normal,” I agree with your point, but I would not want to overclaim it as automatic root-cause diagnosis at first. A realistic first step would be learned baseline comparison for that specific vehicle and operating condition. For example, a value would only be compared against similar conditions: RPM range load / MAP throttle position gear / vehicle speed coolant and oil temperature battery voltage AFM/DFM state, if decoded and validated Then the report could flag things like: this periodic message disappeared compared with its normal timing this value deviated from this vehicle’s normal range under similar conditions the same abnormal pattern repeated after the same type of event the anomaly occurred together with voltage, oil-pressure, misfire, or communication changes But I would still call that “abnormal pattern detected,” not “replace this part,” unless there is enough validated repair data behind it. So the intended product would not be “here is a huge log.” It would need to be an event package: what triggered the capture how much pre/post data was preserved what changed before and after the event whether the device itself reset, overflowed, or saw a bus error selected graphs around the event raw data only as supporting evidence From your perspective, what would make this kind of report useful instead of just another datalog? For example: What are the top 5 parameters or events you would want highlighted first? Would you trust a learned baseline for that specific vehicle, or would you prefer fixed thresholds? How much false-positive flagging would be acceptable before you stopped looking at the reports? What would a one-page report need to show for an independent shop to take it seriously? For misfire, AFM/DFM, oil pressure, or U-code complaints, what would you want the tool to flag automatically?
    • 2024 Silverado 2500 HD LTZ grille no camera Parts list   84603331 84913656 84913657 84913654 84913655 84911567 84911568 85646092 85646093 85797921 85797922   11570637  x10-15   grille/bumper bolts 11546500  x10      grille clips 11571006  x10      push/retainer clips 11546454  x6       nut retainers 11611609  x6       M5 bolts 11610700  x6       molding/trim retainers
    • And use RA's 5% discount code if you buy from them.  google for the code, one is always available.
    • Just don't turn the steering wheel as much?
    • Rockauto bud. I pass local stores for parts.   Findya something online. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...