Jump to content

Recommended Posts

Posted

Thought that this might be a thread of interest and maybe a way for some to keep track of their oil changes. Basically post the vehicle you changed the oil on, at what mileage and how long you go on the oil change. If you follow the oil life monitor (OLM) then post at what percent it was reading at the time of the change. Also what brand oil/weight and oil filter you use.

Here is an example;

7/21/18
2002 Silverado
182,157 total miles on truck
5,147 miles on oil OLM at 0%
Oil AMSOIL Signature Series 10w-30 out SS 0w-20 in
Ea064 filter out and Ea030 filter on
Sent sample off to Dysonanalysis to see how this sample did. Reason for so short is I changed out the oil pan, intake gaskets and rear main seal so there will be some sealant in there somewhere. My oil consumption went to 0 after the intake gasket change. So it must have had a small leak. I use to go through a qt in 5k miles. No more smoke on start up after pulling the trailer either so I'm happy.

Also I have been running E85 for most of this oil change and I want to see what effect it has had on the oil.

  • Like 1
  • 1 month later...
Posted (edited)

10/12/18

2016Suburban

36,228 total miles

15,033 miles on oil OLM at 7%

Oil AMSOIL Signature Series 0w-20

Ea017 filter

Edited by Black02Silverado
  • Like 1
Posted (edited)

10/16/2018

"Pepper" - 2015 Silverado 1500

4.3 Ecotec3

6 quarts Red Line High Performance 0W20

WIX filter WL10255

80,000 miles

5,000 Interval (33% OLM)

Sample sent off to Dyson for UOA. Never done this before. (Thanks Nick!)

 

 

Edited by Grumpy Bear
  • Like 2
Posted (edited)
10/18/18
2014 Chevy Cruze diesel
68,487 miles
7,000 miles on oil  OLM  @ 3%
AMSOIL Signature Series DHD 5w-30
Wix CL10021 oil filter

 

Edited by Black02Silverado
  • 2 months later...
Posted (edited)

12/29/18

2014 Silverado 1500

55,908 miles

4936 miles on oil, OLM @ 40ish%

AMSOIL Sig Series 0w20 out and back in

Wix 57045 oil filter

 

Forgot to add, I only run E85 in this truck unless I travel somewhere it isnt available.  Total I've probably ran 10 or less tanks of normal gas.

Edited by DirtyMarcus
  • Like 1
  • 3 weeks later...
Posted

01/09/2019

Pepper: 2015 Silverado 1500 WT1

4.3 Ecotec3

6 Quarts Red Line 0W20 High Performance

NAPA Platinum filter

Nominal 85,000 miles

5,000 mile interval

38% OLM

No perceivable usage. 

  • Like 2
  • 3 weeks later...
Posted

02/06/19

2019 Silverado CC standard bed

6.2l

2 gallons of AMSOIL OE 0w-20

PF63E oil filter

577 total miles

98% OLM

 

Just my usual early oil change that I do on all my new vehicles.

  • Like 1
Posted
2 hours ago, Black02Silverado said:

02/06/19

2019 Silverado CC standard bed

6.2l

2 gallons of AMSOIL OE 0w-20

PF63E oil filter

577 total miles

98% OLM

 

Just my usual early oil change that I do on all my new vehicles.

At-a-boy Nick!

  • Thanks 1
  • 2 months later...
Posted

5/4/19

2014 Silverado 1500

5.3

60894

4934 on oil, 38% on OLM

Amsoil sig series 0w-20 out and back in

Wix filter 10255 installed

Only running e85 and sending oil out for my engines first oil analysis. 

  • Like 3
Posted (edited)

04/06/2019

2002 Silverado CC standard bed

5.3l

6qts of AMSOIL ALM 5w-20 this time

EaO30 oil filter

5,561 miles on oil

187,717 total miles

0% OLM

 

Here is the UOA.  The oil before this one was AMSOIL's ATM Signature Series 10w-30.

 

2002 UOA May2019.jpeg

Edited by Black02Silverado
  • Like 1
Posted

What are your thoughts on the UOA's? The compare looks very favorable to me. 

 

3 hours ago, Black02Silverado said:

04/06/2019

2002 Silverado CC standard bed

5.3l

6qts of AMSOIL ALM 5w-20 this time

EaO30 oil filter

5,561 miles on oil

187,717 total miles

0% OLM

 

Here is the UOA.  The oil before this one was AMSOIL's ATM Signature Series 10w-30.

 

2002 UOA May2019.jpeg

 

Posted

The results are good.  The oil did it's job well.  The issue is the engine is beating it up. High nitration.  Basically ring blow-by.  I need to check my PCV.  I have not done that in a while.

Also, some how oxidation caused the oil to thicken.  It basically became a 0w-30.

 

I have never had good results with nitration ever since I purchased this truck since new.  Got to wonder what is causing it?  It is tuned with Black Bear and it sees nothing but Exxon 93 and some E85.

Posted
5 hours ago, Black02Silverado said:

The results are good.  The oil did it's job well.  The issue is the engine is beating it up. High nitration.  Basically ring blow-by.  I need to check my PCV.  I have not done that in a while.

Also, some how oxidation caused the oil to thicken.  It basically became a 0w-30.

 

I have never had good results with nitration ever since I purchased this truck since new.  Got to wonder what is causing it?  It is tuned with Black Bear and it sees nothing but Exxon 93 and some E85.

What is considered an acceptable Nitration value? Yours look allot like mine. I saw the W30 like 212F value. 

Posted
2 hours ago, Grumpy Bear said:

What is considered an acceptable Nitration value? Yours look allot like mine. I saw the W30 like 212F value. 

Terry said it should be below 10.  As you can see it has never gotten that low.

  • Thanks 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • Congratulations Isttype, on your gmc. Really like my 2024 2500hd sle doublecab now with 85,500 miles.  I checked the oil today at 4800 miles since last oil change and barely reading on the stick.  I don't care if GM says it's Acceptable adding a quart every 2000 miles because that is 100% BS, It is not a 1966 Harley Shovelhead! Sounds like it's setting up a future failure like I had with my 1500 6.2l. Other than oil consumption problems, I really like the 6.6l gas and 10 speed is really nice.  Towed a light 4000 pound trailer last week and averaged 14 mpg.  I was pretty impressive that a 7300 pound gas truck did 14mpg towing, Later-
    • Long Term Cold Cycle Limited Testing   Back to the 1990's and XOM's million mile test. Since then there have been others and there will be more. Schaeffer's, AMSOIL to name two. Of these Schaeffer's is the stand alone which I will explain in a bit later.    http://papers.sae.org/600190/:   http://papers.sae.org/850215/:   Up to 75% of  engine wear occurs on cold starts. These two links (above) provide the technical reasons for engine wear. In a nut shell, and by a large margin, cylinder wear is what takes out most motors and even with a pre-oiling system that part of the engine is dry enough on cold starts and cold warm up to pierce Stribeck.   So when you put a motor, or a car, on a dyno for a million miles stopping only for oil changes, (yes fuel is uninterrupted) or break down maintenance, you are depriving the test of the most important part of it's wear cycle. Yes a million is then a pretty easy walk even for a mineral oil under those conditions.    How about cleanliness during the long test cycles? Same thing. Varnishes that stick rings and insulate parts are laid down by repetitive 'heat cycles'. It's the cool down the precipitates the varnishes. These long runs also hinder acidic attack caused by cold start richness and less than optimal cold start ring sealing. They hinder water formation and enhance breathing of the crankcase; the petri dish of acid formation, the first step in sludge formation, amalgamation and precipitation. These motors are also monitored and controlled for water and oil temperatures to within the "normal operating range".      https://www.swri.org/sites/default/files/sequence-iiih-test.pdf Note the test sequence in some boutique oils literature for testing, API IIIH, is not the standard used for the ILSAC G7 testing. Does that mean it is irrelevant? No, not as used. As used as a 'visual guide' it makes it's point. The G7 weighted piston deposit minimum is lower.      Back to Schaeffer's. That was a cyclical test of an engine in fleet service and not a dyno mule and if you saw the video it was not mirror clean but wear was low.    There are oils like BioSyn and other 'Renewable" source oils that taught cleanliness and have proven themselves in fleet testing. Havoline an other example.    The newest ILSAC G-7 test prioritize cleanliness, LSPI mitigation and fuel economy OVER WEAR. In comparison Porsche C30 Specification Verses ILSAC G-7 Specification below:      Some will balk that this graph isn't apples to apples and I will challenge that in that this graph represent the SPECIFICATION and not the any One Oil Performance.   It is absolutely possible to minimize wear, maximize cleanliness and mitigate LSPI etc., It just isn't cheap and currently I see none that are not walking toward profit over performance.     
    • I don't think you will need a split, separate product, etc., the OBD port should be able to deliver everything you need. Since your device would be plugged into it all the time, it wouldn't miss anything.    Hardware in this case will be the easiest part of your project - ELM 327 devices will already deliver all the data you need. Reporting/software is where your advantage/marketability is.
    • I do too. I’ll never be stuck again 😂
    • It has happened to me a few times. I carry a jumpstart-tire inflator with me.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...