Jump to content

Black AT4 emblems

Dick Messerly
 Share

Recommended Posts

2000 Enthusiast

2000

Posted
Posted
2 hours ago, Libertas said:

84644535

84644536

 

They are separate part #'s for the Left and the Right.  In the parts catalog, they are listed as F Sleeve

Thank you. 

  • Replies 62
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Dick Messerly
Dick Messerly

Got the new carbon flash black AT4 emblems! They are looking great!!! 

Dick Messerly
Dick Messerly

Also decided to plastidip the gmc emblem I don't get why they don't just make them like this it looks so much better! 

Dick Messerly
Dick Messerly

Sorry it took me so long to get back to you all! I'm actually a salesman at a gmc dealership so I've been putting in the hours for end of the month! The 2 part numbers are 84690478 and 84680479 AT4 em

Posted Images

Libertas Enthusiast

Libertas

Posted
Posted
On 2/29/2020 at 6:14 AM, 2000 said:

Thank you. 

You're welcome.  I just had an exhaust shop put on my Borla exhaust today, and requested they change out my exhaust tips.  Unfortunately, they said they couldn't get to the bolts to do it.  I am faaaaar from mechanically inclined, so now I'm not sure what I'm gonna do.  Might have to check with the dealer to see how much they would soak me to install them. ?

bdup Enthusiast

bdup

Posted
Posted
1 hour ago, Libertas said:

You're welcome.  I just had an exhaust shop put on my Borla exhaust today, and requested they change out my exhaust tips.  Unfortunately, they said they couldn't get to the bolts to do it.  I am faaaaar from mechanically inclined, so now I'm not sure what I'm gonna do.  Might have to check with the dealer to see how much they would soak me to install them. ?

 

Installed my black tips tonight.  It was definitely a struggle getting the first one done, it’s really tight under there. 

 

For me a 10mm ratcheting wrench was key to the removal and reinstall. First remove the top bolt with a 10mm ratchet & extension. Once the top bolt is out, you can pull down on the tip and this will allow more access to the left & right bolts. Remove the inside bolt first and outside bolt second with a 10mm ratcheting wrench. Repeat in reverse order when installing new tips. Don’t fully tighten the left or right bolt until you’ve got both bolts started.

Bjeremi Enthusiast

Bjeremi

Posted
Posted

Ordered mine today.  Thanks for the part numbers guys!

 

 Still want to do something with the GMC logos as well.  Going to go with Bronze Fuel wheels so think I am just going to get rid of as much of the chrome as possible.  

  • 4 months later...
Patrick Barrett New Member

Patrick Barrett

Posted
Posted
On 2/3/2020 at 12:43 AM, Dick Messerly said:

84690478 is the bigger door one 84690479 is the smaller tailgate one. 

Anyone else getting the description as "F Plate" for the door badge? Tailgate one is full description, but door one basically says nothing.

  • 2 weeks later...
2020AT4 Enthusiast

2020AT4

Posted
Posted

Looks sweet on the gray color truck. I went with black for body color, probably wouldn't look at good on mine; wouldn't even be able to see them.

jsarratt New Member

jsarratt

Posted
Posted
On 1/29/2020 at 9:56 PM, Dick Messerly said:

Also decided to plastidip the gmc emblem I don't get why they don't just make them like this it looks so much better! 

IMG_20200129_225607_235.jpg

did you take it off to do it 

  • 3 months later...
cboveda New Member

cboveda

Posted
Posted
On 1/30/2020 at 12:49 AM, Dick Messerly said:

Got the new carbon flash black AT4 emblems! They are looking great!!! 

20200128_160340.jpg

20200128_160332.jpg

Any “how to’s” to line up the replacement emblem?

polarys425 Enthusiast

polarys425

Posted
Posted
On 3/2/2020 at 11:38 PM, Libertas said:

You're welcome.  I just had an exhaust shop put on my Borla exhaust today, and requested they change out my exhaust tips.  Unfortunately, they said they couldn't get to the bolts to do it.  I am faaaaar from mechanically inclined, so now I'm not sure what I'm gonna do.  Might have to check with the dealer to see how much they would soak me to install them. ?

Small air ratchet.... it'll slide right in there.

  • 2 months later...
Musgo Enthusiast

Musgo

Posted
Posted

Those badges look awesome!!!!!   I plasti dipped my 2014 Denali badges black.   The only issue I had was the front would chip and flake from rock strikes.  So I would touch it up every couple months.  Anyone have suggestions on making the front panted emblems more durable?

  • 4 weeks later...
Rgpie75 Enthusiast

Rgpie75

Posted
Posted
I ordered some decal overlays and did mine. 
 
09DDFE58-510B-4D04-9AED-7617E890B562.thumb.jpeg.be582ab312465a3901598e46c724d93d.jpeg

How hard were these to line up when installing? Not a bad option for $20 or so.


Sent from my iPhone using Tapatalk
kpromero Enthusiast

kpromero

Posted
Posted
14 minutes ago, Rgpie75 said:


How hard were these to line up when installing? Not a bad option for $20 or so.


Sent from my iPhone using Tapatalk

I am no expert and found them to be not too bad to apply. They fit just inside the chrome layer and I used a blow dryer to heat up and a credit card to tuck the edges 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • JimCost2014
      Towing In Loose Gravel

      By JimCost2014 · Posted

      If what you are doing works, keep doing it:   4LO (Four-Wheel Drive Low) should only be used in extreme low-speed, high-torque situations such as deep mud, heavy snow, steep rock crawling, or extreme inclines/declines, and you must follow the correct engagement procedure to avoid drivetrain damage. Intended Use Cases Deep mud or snow where traction is extremely poor and you need maximum torque to get unstuck Trucks Only+1. Rock crawling on steep, uneven terrain forum.fullsizechevy.com+1. Extreme inclines or declines where you need to control speed and maintain traction solutionsphere.blog. Heavy towing in low-traction conditions (e.g., deep sand, ice) carclubsusa.com.
    • rdonarski
      Towing In Loose Gravel

      By rdonarski · Posted

      Hi,   I work a steep boat landing that has patchy blacktop going down the hill and soft sand/gravel at the bottom. Due to low water levels, it's not always possible reach the blacktop. I've had to help several people get out this year already and with fall coming, I'm anticipating more. I always use 4L. There was a gentleman there today with a 2500 HD (actually 2 - him and his son both have them) and they were trying to get his son's wake boat out. This gentleman swears that you should use 4H in the soft gravel. Says he was a farmer and you always use higher gear when stuck. I was wonder what your thoughts on this are? If I'm wrong, it would be good to find out before things get busy.
    • Bill Lemmond
      Roll up bed cover experiences

      By Bill Lemmond · Posted

      Looking for feedback from users of roll up aluminum slat bed covers who have had it for more than 3 years. I prefer the aluminum slat style over supported vinyl covers due to security and the capacity to support a light load. The slight loss of bed opening when rolled up is not an issue. Presently have BAK Revolver the "industrial grade vinyl overlay" on mine is shrinking & coming loose at the rear and on both sides in addition to cracking at some of the folding joints. Truck lives outdoors in NC latitude. Can't justify the steep price to replace it with another one if that's the expected lifespan. Do you have a better alternative?
    • Bill Lemmond
      BAK Revolver bed cover

      By Bill Lemmond · Posted

      Thanks, your last sentence is the root of my problem, outdoors truck and southern latitude = UV overload. Looking at replacing with Rough Country powder coated aluminum slat roll up model. 
    • JakeD
      Tire fitment

      By JakeD · Posted

      I’m looking at putting a lift in my 2024 gmc sierra 1500 elevation trim, has anyone had any luck with fitting a bigger tire under the rear for a spare?? Was gonna go with a 4 inch zone lift Also what wheel and tire size setup are you all running? Wondering if I can get away with keeping around the stock size a 33 inch, and just get some new wheels to have enough back spacing then I can just keep my original spare tire I have under the truck now.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...