Jump to content

Tightening front shock nut HELP

danmc96
 Share

Recommended Posts

danmc96 Enthusiast

danmc96

Posted
Posted (edited)

I mistakingly removed the nut on top of my front passenger side shock while installing MotoFab front leveling kit. I got everything back together but the shaft spins and I can’t grab it with anything due to it being sunk into frame. Any ideas on what to use to tighten this up?   I’ll try to snap a pic tomorrow. 

Edited by danmc96
davester Senior Enthusiast

davester

Posted
Posted

Typically, the tip of the shock is used to prevent it from rotating.  Some will have provision for an allen key (or something similar), some will have a machined in square or hex to put a wrench on the end.

Ryguy Enthusiast

Ryguy

Posted
Posted

Wait you removed the top strut bolt that holds the spring down? Did you remove it completely? If so you will need to pull the coil over out and use a spring compressor to re-secure the nut.

CamGTP Senior Enthusiast

CamGTP

Posted
Posted

A vise grips with some rubber hose on the ends would work if you can get it to grab on to the shock piston through the coil spring. Then brap it down with an impact gun.

AJMBLAZER Enthusiast

AJMBLAZER

Posted
Posted

I have had good luck with the weight of the truck pushing down on it and the impact going to town.
 

If you are asking how to reassemble a completely apart strut and coil Then yes, you will need some spring compressors.

  • 8 months later...
andrewb24 Enthusiast

andrewb24

Posted
Posted
On 5/16/2020 at 12:51 AM, danmc96 said:

I mistakingly removed the nut on top of my front passenger side shock while installing MotoFab front leveling kit. I got everything back together but the shaft spins and I can’t grab it with anything due to it being sunk into frame. Any ideas on what to use to tighten this up?   I’ll try to snap a pic tomorrow. 

whats the update on this issue? were you talking about the center nut on the strut?

Gangly Senior Enthusiast

Gangly

Posted
Posted

I did the same thing while not paying attention awhile back.  I had to remove the coil and shock from the vehicle to repair it.

  • 3 years later...
rahool82 Enthusiast

rahool82

Posted
Posted (edited)

Can you tell me how you got the spring out? The top of my strut snapped off and I've tried lowering the control arm as far as it'll go but I can't get pressure off it. I'm thinking my only option are the widow maker spring compressors if I can get them in there and cranked down. Looks like it might work but I'm not exactly rushing to try it lol. Any ideas or tips greatly appreciated!!

Edited by rahool82
asilverblazer Senior Enthusiast

asilverblazer

Posted
Posted (edited)
4 hours ago, rahool82 said:

Can you tell me how you got the spring out? The top of my strut snapped off and I've tried lowering the control arm as far as it'll go but I can't get pressure off it. I'm thinking my only option are the widow maker spring compressors if I can get them in there and cranked down. Looks like it might work but I'm not exactly rushing to try it lol. Any ideas or tips greatly appreciated!!

With weight on the strut, you can wrap/lace the spring (the weight on it keeps it compressed some) with a heavy gauge wire. The more and tighter you get it laced the safer it will be. It should be enough to hold it all together to get it out of the truck. Unless you have a fancy strut compressor, then the dangerous part of getting the wire off while under tension. At least its not going to damage the truck and its not right in your face either.

 

Out of the truck you could take it to a shop too.

Edited by asilverblazer
rahool82 Enthusiast

rahool82

Posted
Posted (edited)
2 hours ago, asilverblazer said:

With weight on the strut, you can wrap/lace the spring (the weight on it keeps it compressed some) with a heavy gauge wire. The more and tighter you get it laced the safer it will be. It should be enough to hold it all together to get it out of the truck. Unless you have a fancy strut compressor, then the dangerous part of getting the wire off while under tension. At least its not going to damage the truck and its not right in your face either.

 

Out of the truck you could take it to a shop too.

Not a bad idea, might do this in addition to the screw down compressors, just for some extra pieces of mind. Thanks!

 

No fancy spring compressors here, just the old beater rentals from autozone

Edited by rahool82
asilverblazer Senior Enthusiast

asilverblazer

Posted
Posted
20 hours ago, rahool82 said:

Not a bad idea, might do this in addition to the screw down compressors, just for some extra pieces of mind. Thanks!

 

No fancy spring compressors here, just the old beater rentals from autozone

Get it out of the truck then using the rent-a-compressor will be easier.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,897
    Total Members
    8,960
    Most Online
    ncleg
    Newest Member
    ncleg
    Joined

  • Who's Online   1 Member, 0 Anonymous, 1,265 Guests (See full list)

  • Latest Articles

  • Posts

    • dna9656
      New to Me 2010 SLE (Quirks, Issues)

      By dna9656 · Posted

      Your tire pressure issue may just be batteries, you can reset them using tge Ing switch (I think) and the owner's  manual. ChatGTP will b e a faster, better help than Google.
    • Another JR
      Towing In Loose Gravel

      By Another JR · Posted

      The thinking is that starting out in a higher gear makes it easier to avoid applying excessive torque when pressing the gas pedal. In a modern 4wd truck with 4 low and a limited slip or locking rear end, I would use 4 low and try to crawl up the ramp. Sometimes if they are too slippery, you have to back up to let the boat have some bouyancy, and then accelerate briskly to get some momentum to help you pull the through the slippery parts. 
    • XY74
      Roll up bed cover experiences

      By XY74 · Posted

      I have a Retrax pro that I first had on my 2020 chevy and transferred it to my current GMC.  It stays in the garage most of the time, so hard for me to judge it's long term weather resistance.  It still works perfectly, been very durable.  It doesn't see oil patch usage, but it's not a mall queen.  It keeps most things mostly dry (small leaks) and the security of it is enough to slow someone down but not keep them out for long.  I would buy one again, it works for me.     
    • fm2176
      New to Me 2010 SLE (Quirks, Issues)

      By fm2176 · Posted

      Thanks to the convenience of Amazon, I was able to get a few things done to the truck today.  I installed Carquest Premium oil and air filters with five quarts of Mobil1 High Mileage 10-30 along with a quart of Pennzoil Platinum 5w-30 I already had.  The latch for the flip up center console lid was broken so I replaced it along with the power mirror switch.  I found my push retainer assortment this morning and reattached the plastic under the bumper and it was only held on with a few screws and retainers.  Then I programmed a new remote keyless entry fob so I can lock my dog in the truck when I take her out with me (I've got to keep the air going for her since it's been in the 100s).  Finally, I ordered some LED interior bulbs and replaced the reading lamps.  The front lights are working fine while one of the back lights only works intermittently and the other not at all.   While under the truck, I found the source of at least one of the noises: the sway bar links need replacing.  I ordered a set of Suspension Dudes links with Code Red bushings.  Never heard of them, but they're made in the USA and have decent reviews.  While making yet another Amazon order, I went ahead and added a set of front tow hooks.  I went with red, since that's the color of the sway bar link and bushings and it should look decent enough on a black and chrome truck.  Speaking of which, it doesn't bug me much, but the passenger side mirror has a chrome cap while the driver side doesn't, so eventually I'll make them match one way or another.  Oh, and I ordered a $20 TPMS reset tool.  No idea if it will do anything for my sensors but it was cheap and will work for the Ford Transit Connect as well.     For tradition's sake, I ordered a new oil change wrench.  I kept the Snap-On 9/16"x15mm GM wrench I bought when I was 18 in the 2006 GMC from the time I bought that truck until the truck was lost.  While I was tempted, there's no need to spend $80 for a new SO wrench, or even $50 with shipping for a used one on Ebay.  I just bought a Duratech 15mm extra-long ratcheting wrench to do the job as needed.  It works, and if I like that wrench enough, I'll buy the set.  
    • Another JR
      Multigate electrical problem

      By Another JR · Posted

      The recall is for exactly this issue - those drain holes combined with the limited environmental capability of the tailgate electronics card inside the tailgate were a problem. The “safety issue” was the potential for the tailgate to spontaneously open, but all kinds of tailgate misbehavior can occur from water contamination of that control card.    There is no real fix yet. The initial recall just disabled the tailgate. Later, when parts became available, they would replace bad parts with new parts of the same bad design. My dealer is going nuts because the few times I let them get their hands on my truck, my tailgate is off due to a slide-in camper installation. They really want to cut my tailgate wires, but I won’t give them the chance. I will let them get their dirty hands on it when a real fix (redesign) is available.  My tailgate, which works just fine with sealant plugging the drain holes, will remain safe in a dry storage crate until then.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...