Jump to content

Recommended Posts

Posted

I did a quick search and I think my pinion seal is going bad. I’m having fluid flung onto my gas tank. Also getting a shutter sometimes on certain hills pullin my trailer. I’ve attached fluid 

1590D10E-6726-4015-B438-9006FAB3FAF4.jpeg

FCCFE316-645B-46B7-9522-A5DF40B21D8A.jpeg

Posted (edited)

What is the ziptie for, and what is it holding in place?

 

Wonder if it is a gas leak, just by the way it looks like it is eating the coating away on the piece in the picture?

Edited by JimCost2014
Posted

Looks like a fuel leak. Just fast enough to keep some of the dirt washed clean. Any leaking oil won't be clean to bare metal. It would just keep getting layers of oil and dirt. Gas will keep cleaning.

Posted (edited)

Like the old cheech and chong skit...look smell taste. Do you smell gas?

 

PS...what is up with the white zip ties?

Edited by gemarsh
Posted

If that is diff oil then it  will stink like diff oil.  You can't forget that smell if you ever changed out the fluid before. 

  • Haha 1
Posted
On 9/25/2021 at 5:52 AM, Black02Silverado said:

If that is diff oil then it  will stink like diff oil.  You can't forget that smell if you ever changed out the fluid before. 

It definitely smells like gear oil. Has lubricity like gear oil.   Everything around the pinion is oily. The tank is only wet on the side where the gear oil is being flung. Above the pinion is the bottom of the truck bed and that is wet. Dirty is sticking and making a mess. 
 

Posted

I’ve added more photos. Everything I’ve circled has oil on it. The arrows represent the direction at which the oil is being flung. Looking at the shield over the fuel tank is a give away. And then on the bottom of the bed. It all correlates. 
 

also; I’ve also been experiencing a shutter at times on certain on some interstate hills. Doesn’t do it all the time. Im hoping this is related to low diff fluid and nothing more serious so we will see. 

EA5C9EEC-3008-4ECE-8796-8A0BF035E2C9.jpeg

E9E1E317-BCFF-4E97-83B7-52075576CE5A.jpeg

6E0E60BD-FD0D-42FB-B630-59C8F184E82A.jpeg

307A4891-424A-4613-B11B-E7A37BFB34FF.jpeg

267D64B5-7D01-47D8-8E93-076704569CE6.jpeg

Posted
On 9/24/2021 at 10:20 PM, JimCost2014 said:

What is the ziptie for, and what is it holding in place?

 

Wonder if it is a gas leak, just by the way it looks like it is eating the coating away on the piece in the picture?

Zip tie is holding my solenoid off of my original magnaride shock. I switched to a spring/shock and to bypass the “service suspension” warning  you can remove the solenoids from the original shock and plug them in and trick the sys. I will probably go back to magnaride soon lmao. 
 

  • Thanks 1
Posted

Are you getting the seal replaced? I see in your other pics your right about where it's leaking from.

Posted
On 9/27/2021 at 2:19 PM, zhmorrow said:

Zip tie is holding my solenoid off of my original magnaride shock. I switched to a spring/shock and to bypass the “service suspension” warning  you can remove the solenoids from the original shock and plug them in and trick the sys. I will probably go back to magnaride soon lmao. 
 

That's one strange pinion seal leak.

 

Thanks for the pictures. I have done all the oil changes on the 21, but never bothered to look at the driveshaft. It's good to know that gm did away with that damn melted plastic to retain the caps of the u-joint.

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • It really is comical when people don’t agree or see the reason some people prefer the older vehicles. They become condescending. All the while they may be busting their knuckles on old vehicles. I have found memories of swapping out engines in my old GM cars in a weekend without much hassle. Unlike today. One wrong move a computer will shut you down. Even on something as easy as a brake job. There’s a pretty comical YouTuber called the car wizard. A garage owner who puts it all in perspective. Another Vicegrip garage that’s shows just how tough the old stuff is. 
    • I was around and remember that era very well, so I'm calling b/s on that statement. If they were that bad no police department or taxi company would've bought a single one ... but they were used in both services (and fire) for DECADES. They were bulletproof and proven. Even the early 21st century ones weren't too bad! The early models were legendary.   Mine is proof, but people like atlas are blinded by agenda and refuse to believe facts right before their very eyes.   Even decades after they were built, a new generation started driving them, posting all their builds and shenanigans on Grandmarq.net and Crownvic.net. The failures would show up then, since they all were deep past 100k-150k miles by that point, and younger drivers tend to be a little aggressive, especially with vehicles than can lay a one-tire fire for as long as you hold your foot in it. They've more than proven themselves over the decades.   The only thing that'll really take them out is road salt. The bodies and sheet metal were garbage. A victim of the cheapout FoMoCo and GM have been partaking in before then, and since.   Today it's the stuff that counts - the undercarriage that rots away first!    GMs Caprice was no slouch either. Reliable as a stone ax - the opposite of what they build now.    
    • Let me know how your vehicles do in 10 years. You don't know ******, kid. 😂    There's a reason that Panther platform was used as police, fire, and taxi service for DECADES ... long before you were born, apparently.
    • If your connector also has a big lever to get the connector on and off, you don't want to force the lever either way, as it becomes a bigger problem if you bust the lever or the mechanism it works.
    • It's just useful to disconnect the battery to prevent odd shorting out when unplugging/plugging stuff together.  I also  touch the two cable ends together (after disonnecting) to drain the small amount of stored battery energy in various modules.   I believe the main system where you need to be more concerned with, so you need to do the above and then wait some time, iss when you are working on the air bag system, to prevent inadvertent firing of the air bags.   The in-cab switches are just that, plain switches, it's generally not a problem to swap them in/out.  For my '12, I'll get an error message on the dash if I power up the truck w them unplugged, but that's it (power up= turn the ignition on).   The ITBC located above the spare tire is a computer that manages the trailer brake system.  That is probably more important to have the battery disconnected.  It does have to be programmed to the truck, either before or after it's installed, for it to work.  For my '12, I had a very hard time reinstalling the main connector to it (IDK if yours is the same or not), it turned out the silicon seal was jamming up, preventing it from going on all the way.  I finally got it fully installed by lubing the seal with a bit of dielectric grease, then it slid on and latched in place easily.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...