Jump to content

Recommended Posts

Posted

Spotted 63 antelope while driving today

Posted

GM really compacted everything under the hood of the newer diesels.

Posted

The other driver in my parents accident didn't have valid insurance. He said he called to ask why and they told him he is behind on payments.

 

He told my Dad to have the car checked out and he will make it right(it's an 02, so it's totaled) question is will repairs exceed value competely. Fender, hood work, bumper, air deflector, and labor and paint, I'm betting yes.

  • Like 1
Posted

Lost 3 hours last night pulling the front end off my truck to change out a headlight!!!!!!! I think that who ever came up with this brain child should be required to go and change out at least one in every state on their own dime. Also I would make sure and have them do it in the grass somewhere at night!!!!! Can you tell that I am al little up set about it all? I went ahead and bought all the bulbs and changed them all out so I should be good for another 4 years and 80,000 miles. The good news is it only took about 1 hour to put it all back together. :jester:

I was about to have the same deal with my Wife's Traverse. Headlight went out, so I popped the hood and began removing the plastic shroud. Then found out I couldn't get to all of the headlight bolts. Too tight to reach my hand down there. Then I fired up the trusty YouTube. Now, I can change BOTH headlights in under 15 minutes through the fender well....and that includes getting the 1 tool out, turning the wheels to the left for the passenger side, and then turning them to the right for the driver side.

  • Like 1
Posted

Started heading west, stopped, unhooked camper, and headed back east.

Posted

Spotted 63 antelope while driving today

 

are you rainman?

  • Like 1
Posted

I found my exhaust leak today! Hard to miss, but this was the first time I looked for it...

 

IMAG1015_zpswjiziygl.jpg

 

With this many miles, I should probably do new gaskets. Or do you think I'll have any luck tightening these bolts down? I'm terrified to break the bolts. I would have tried tightening them at the time, but the engine was quite warm when I took the picture.

Posted (edited)

I'd vote new bolts and gaskets. Do it right, do it once.

 

But....yeah, I'd worry about breaking a bolt also.

Edited by SnakeEyes
Posted

How do I get that rear bolt off? It looks more like a stud than a bolt, but then I wonder how the stud would stay "tight".

 

For reference, the right side is closest to the passenger headlight.

Posted

are you rainman?

Not at once, a lot of small groups.

Posted

The truck got to double as a workbench the last couple of days. Building a porch/deck for a neighbor. Sunday was just that...sunny and HOT! Yesterday I didn't get to help out until after work so I didn't help a whole lot.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Latest Articles

  • Posts

    • This is interesting. My quote tagged here is different from my original quote. After I’m driving them longer. That isn’t me. I don’t talk that way. I definitely wouldn’t express myself that way. Interesting.
    • I have the same running boards on my truck and I do agree they are bulky. I also find myself stepping over them when getting in and out of the truck. Besides providing protection to the rocker panels, they aren't very useful.  I will be replacing them soon with the Amp Powersteps. 
    • Monthly payment is only part of the equation. With today's prices and interest rates, I'd look at the total monthly cost: payment, insurance, registration, fuel, maintenance, and expected repairs. A vehicle that fits comfortably into your budget is usually the better choice than stretching for a higher trim. I've also kept my vehicles longer over the past few years. New cars have gotten expensive enough that driving one for 10+ years, while staying on top of maintenance, often ends up being the most cost-effective approach.
    • 10 Ford and Chevy engines proven to reach 300,000 miles   You may note a common 3K OCI on this list of gas motors. I skipped over the diesels. Dh'O. 
    • Thanks newdude!  By the time manual selection is needed, I'm probably too much of a control-freak to depend on the transmission sensing braking to activate automatic downshifting.  I would be anticipating the situation and already be manually downshifting.   This truck replaced a 2004.5 LLY diesel with the Allison 5-speed.  Putting it in T/H made noticeable differences (when the torque converter locked, upshift points, downshift behavior).  On this 2024 gasser with the 10L1000 I haven't been able to detect much, if any, difference.  Ok, I can never tell now when the torque converter locks up.  But I also don't notice differences in shifting.  For downhills, I've probably already manually downshifted by then anyway.  Since it's also more awkward (than the 2004.5) to engage/disengage I don't even bother.  Or maybe it doesn't really matter with just a 3k lb. camper in the bed?   Thanks also for the list of reasons the charging system might select various voltages.  However, what I am seeing doesn't fall into any of those categories.  It very definitely, and very consistently, rises after coasting/braking.  Maybe not immediately, but not very long after coasting/braking.  Very consistently drops voltage when no longer coasting/braking.  It might also be interacting with the camper battery charging (I might disconnect the camper and see if it changes the charging behavior).  I also need to recheck turning on headlights for when I want to force it to charge the camper.   Another JR, in June I converted the camper to LiFePO4.  Since it's not a good idea to try to charge lithiums directly using truck, I installed a Victron Orion XS DC-DC charger (which BTW is AMAZING!!).  Being cheap, I only had to buy that one item (besides the battery, of course) to do the conversion.  The camper OEM 120v battery charger (only 19 years old and works perfectly) and the truck feed the input to the DC-DC charger (not at the same time).  But I didn't want the camper charger feeding back to the truck so I kept the old separator.  I considered replacing the separator with a 30amp diode but that means more work and might add another 1/2 volt drop.  One thing that surprised me was the voltage drop over the long 10awg wire run, so I can only charge smoothly at 8 amps (because the DC-DC charger is completely configurable).  Another reason I don't want an added voltage drop with the diode.  I might also be a little lazy but all this work is being done under the sink with a small cabinet opening.    
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...